jk0061119_eeprom._h

Modbus RTU 的C语言程序

#pragma  data:eeprom
 //char  Voltage_grade_110_220=110;
 char  Address_JK=0x03;
 //char  Flag_COM0_Protocol_eeprom=0;
/////////////////////// 110V电压等级
 char  Voltage_GL_Join_110_Hbyte=0x06;///113v  1543 0x0607
 char  Voltage_GL_Join_110_Lbyte=0x07;
 char  Voltage_GL_Quit_110_Hbyte=0x05;///107v  1461  0x05B5
 char  Voltage_GL_Quit_110_Lbyte=0xB5;
 //char  Voltage_HM_220_High_Hbyte=0x0D; ///262  3577  0x0DF8
 //char  Voltage_HM_220_High_Lbyte=0xF8;
 //char  Voltage_HM_220_Low_Hbyte=0x0A;  ///198  2703  0x0A8F
 //char  Voltage_HM_220_Low_Lbyte=0x8F;
 //char  Voltage_KM_220_High_Hbyte=0x0C;////243  3318   0x0CF5
 //char  Voltage_KM_220_High_Lbyte=0xF5;
 //char  Voltage_KM_220_Low_Hbyte=0x0A;////198   2703   0x0A8F
 //char  Voltage_KM_220_Low_Lbyte=0x8F;
/////////////////////////////////////////////////////
 char  EEprom_array[50]={0x02,0xEE,0x01,0x2c,0x00,0x3c,0x00,0x96,
                         0x07,0x0A,0x05,0x48,0x06,0x74,0x05,0x48,0x00,0x64,0x08,0x70,
						 0x02,0x58,0x00,0xb4,0x00,0x64,0x00,0x64,0x00,0x64,0x00,0x64,0x00,0x64,
						0x00,0x64,0x00,0x03,0x00,0x32,0x06,0x3D,0x06,0x9C};
/////////////////
//char  Password_Level_0_Hbyte=0x15;///5555
 //char  Password_Level_0_Lbyte=0xB3;
 //char  Password_Level_1_Hbyte=0x10;////4321    0x10E1
 //char  Password_Level_1_Lbyte=0xE1;
 char  Password_Level_2_Hbyte=0x08;///// 2222  0x08AE
 char  Password_Level_2_Lbyte=0xAE;
 //char  v_HM_data_potentiometer_Hbyte=0x13;
 //char  v_HM_data_potentiometer_Lbyte=0x88;
 //char  v_KM_data_potentiometer_Hbyte=0x13;
// char  v_KM_data_potentiometer_Lbyte=0x88;
// char  v_MK_data_potentiometer_Hbyte=0x13;
 //char  v_MK_data_potentiometer_Lbyte=0x88;
// char  v_Bat_data_potentiometer_Hbyte=0x13;
 //char  v_Bat_data_potentiometer_Lbyte=0x88;
 //char  A_KM_Load_Current_potentiometer_Hbyte=0x00;
 //char  A_KM_Load_Current_potentiometer_Lbyte=0x64;
 //char  A_CD_Current_potentiometer_Hbyte=0x00;
 //char  A_CD_Current_potentiometer_Lbyte=0x64;
//////////////////充电电流参数设定
 //char  A_Current_Sensor_Hbyte=0x00;//// 100A  0x0064
 //char  A_Current_Sensor_Lbyte=0x64;
 //char  A_Current_BypassSensor_Hbyte=0x02;//// 750A   0x02EE
 //char  A_Current_BypassSensor_Lbyte=0xEE;
 //char  A_Current_JC_Hbyte=0x01;////均充电流值 300A  0x012c
 //char  A_Current_JC_Lbyte=0x2c;////均充电流值
 //char  A_Current_FC_Hbyte=0x00;////浮充电流值   60A    0x003c
 //char  A_Current_FC_Lbyte=0x3c;////浮充电流值
 //char  A_Current_FC_Change_JC_Hbyte=0x00;////浮充转均充电流值//150A 0x0096
 //char  A_Current_FC_Change_JC_Lbyte=0x96;
/////////////////////////////////////////////////////////
/////////////////定时变量
 //char  Time_Interval_JC_Hbyte=0x08;//  2160h
 //char  Time_Interval_JC_Lbyte=0x70;
 //char  Time_Limited_JC_Hbyte=0x02;//600m
 //char  Time_Limited_JC_Lbyte=0x58;
// char  Time_Delay_JC_Hbyte=0x00;//180m
 //char  Time_Delay_JC_Lbyte=0xb4;
///////////////////////////////////////////////
 
/////////////////////////////////////////////////////////
//////////////  LCD显示固定数据库
 char HM[4]={0xBA,0xCF,0xC4,0xB8};//合母
 char KM[4]={0xBF,0xD8,0xC4,0xB8};//控母
 char DY[5]={0xB5,0xE7,0xD1,0xB9,0x3A};//电压
 char CD[4]={0xB3,0xE4,0xB5,0xE7};//充电
 char DL[5]={0xB5,0xE7,0xC1,0xF7,0x3A};//电流
 ///////////////////////////////////////////////
 char ZC[4]={0xD6,0xF7,0xB4,0xB0};//主窗
 char XX[4]={0xD0,0xC5,0xCF,0xA2};//信息
 char CS[4]={0xB2,0xCE,0xCA,0xFD};//参数
 char SZ[5]={0xC9,0xE8,0xD6,0xC3,0x3A};//设置
 char SJ[4]={0xCA,0xC2,0xBC,0xFE};//事件
 char CX[4]={0xB2,0xE9,0xD1,0xAF};//查询
 char BB[4]={0xB0,0xE6,0xB1,0xBE};//版本
 char MM[5]={0xC3,0xDC,0xC2,0xEB,0x3A};//密码
 char JC[4]={0xBE,0xF9,0xB3,0xE4};//均充
 char FC[4]={0xB8,0xA1,0xB3,0xE4};//浮充
 char ZH[4]={0xD7,0xAA,0xBB,0xBB};//转换
 char GY[5]={0xB9,0xFD,0xD1,0xB9,0x3A};//过压
 char QY[5]={0xC7,0xB7,0xD1,0xB9,0x3A};//欠压 
 char JG[5]={0xBC,0xE4,0xB8,0xF4,0x3A};//间隔
 char YS[5]={0xD1,0xD3,0xCA,0xB1,0x3A};//延时
 char XS[5]={0xCF,0xDE,0xCA,0xB1,0x3A};//限时
 char JZ[5]={0xD0,0xA3,0xD7,0xBC,0x3A};//校准
 char JZXS[5]={0xCF,0xB5,0xCA,0xFD,0x3A};//系数
 char CGQ[7]={0xB4,0xAB,0xB8,0xD0,0xC6,0xF7,0x3A};//传感器
 char FLQ[7]={0xB7,0xD6,0xC1,0xF7,0xC6,0xF7,0x3A};//分流器
 char QSR[6]={0xC7,0xEB,0xCA,0xE4,0xC8,0xE8};//请输入
 char DQZT[9]={0xB5,0xB1,0xC7,0xB0,0xD7,0xB4,0xCC,0xAC,0x3A};//当前状态
 char QHW[7]={0xC7,0xD0,0xBB,0xBB,0xCE,0xAA,0x3A};//切换为
 //char ZY[4]={0xD7,0xA2,0xD2,0xE2};//注意
 ////////////////////////////////////////////////////
 char XTZFC[10]={0xCF,0xB5,0xCD,0xB3,0xD7,0xAA,0xB8,0xA1,0xB3,0xE4};//系统转浮充
 char XTZJC[10]={0xCF,0xB5,0xCD,0xB3,0xD7,0xAA,0xBE,0xF9,0xB3,0xE4};//系统转均充
 char JLGZ[8]={0xBD,0xBB,0xC1,0xF7,0xB9,0xCA,0xD5,0xCF};//交流故障
 char JLGDZC[12]={0xBD,0xBB,0xC1,0xF7,0xB9,0xA9,0xB5,0xE7,0xD5,0xFD,0xB3,0xA3};//交流供电正常
 //***char MKGZ[8]={0xC4,0xA3,0xBF,0xE9,0xB9,0xCA,0xD5,0xCF};//模块故障
 char MKGZ[14]={0xB5,0xE7,0xB3,0xD8,0xD5,0xFD,0xC8,0xDB,0xD0,0xBE,0xC8,0xDB,0xB6,0xCF};//电池正熔芯熔断
 //***char MKGZZC[12]={0xC4,0xA3,0xBF,0xE9,0xB9,0xA4,0xD7,0xF7,0xD5,0xFD,0xB3,0xA3};//模块工作正常
 char MKGZZC[12]={0xBC,0xEC,0xB2,0xE9,0xC8,0xDB,0xD0,0xBE,0xD5,0xFD,0xB3,0xA3};//检查熔芯正常
 //***char JYGZ[8]={0xBE,0xF8,0xD4,0xB5,0xB9,0xCA,0xD5,0xCF};//绝缘故障
  char JYGZ[14]={0xB5,0xE7,0xB3,0xD8,0xB8,0xBA,0xC8,0xDB,0xD0,0xBE,0xC8,0xDB,0xB6,0xCF};//电池正熔芯熔断
 //***char JCJYZC[12]={0xBC,0xEC,0xB2,0xE9,0xBE,0xF8,0xD4,0xB5,0xD5,0xFD,0xB3,0xA3};//检查绝缘正常
  char JCJYZC[12]={0xBC,0xEC,0xB2,0xE9,0xC8,0xDB,0xD0,0xBE,0xD5,0xFD,0xB3,0xA3};//检查熔芯正常
 char KMGY[8]={0xBF,0xD8,0xC4,0xB8,0xB9,0xFD,0xD1,0xB9};//控母过压
 char KMQY[8]={0xBF,0xD8,0xC4,0xB8,0xC7,0xB7,0xD1,0xB9};//控母欠压
 char KMDYZC[12]={0xBF,0xD8,0xC4,0xB8,0xB5,0xE7,0xD1,0xB9,0xD5,0xFD,0xB3,0xA3};//控母电压正常 
 char HMGY[8]={0xBA,0xCF,0xC4,0xB8,0xB9,0xFD,0xD1,0xB9};//合母过压
 char HMQY[8]={0xBA,0xCF,0xC4,0xB8,0xC7,0xB7,0xD1,0xB9};//合母欠压
 char HMDYZC[12]={0xBA,0xCF,0xC4,0xB8,0xB5,0xE7,0xD1,0xB9,0xD5,0xFD,0xB3,0xA3};//合母电压正常 
 //char WSJ[6]={0xCE,0xDE,0xCA,0xC2,0xBC,0xFE};//无事件
 char  WSJ[10]="本页无记录";
 //char HM1HZ[10]={0xBA,0xCF,0xC4,0xB8,0x31,0x23,0xBA,0xCF,0xD5,0xA2};//合母1合闸
 //char HM1TY[10]={0xBA,0xCF,0xC4,0xB8,0x31,0x23,0xCD,0xA3,0xD4,0xCB};//合母1停运
 //char HM2HZ[10]={0xBA,0xCF,0xC4,0xB8,0x32,0x23,0xBA,0xCF,0xD5,0xA2};//合母2合闸
 //char HM2TY[10]={0xBA,0xCF,0xC4,0xB8,0x32,0x23,0xCD,0xA3,0xD4,0xCB};//合母2停运
//////////////
////请输入密码:
 char password_in_1[16]={0xC7,0xEB,0xCA,0xE4,0xC8,0xEB,0xC3,0xDC,0xC2,0xEB,0x3A,0x20,0x20,0x20,0x20,0x20};
 char password_in_2[16]={0x20,0x20,0x20,0x20,0x20,0x20,0x0F,0x0F,0x0F,0x0F,0x20,0x20,0x20,0x20,0x20,0x20};
///////////////////密码错误
 char password_error_1[16]={0xC3,0xDC,0xC2,0xEB,0xB4,0xED,0xCE,0xF3,0x20,0x13,0x20,0x20,0x20,0x20,0x20,0x20};
 char password_error_2[16]={0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0xC7,0xEB,0xD6,0xD8,0xCA,0xD4,0x20,0x21}; 
 char password_error_3[16]={0xBB,0xF2,0xD6,0xC2,0xB5,0xE7,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20};
 //////////////////////////////////////////////
 /////////////////软件版本信息
 char Copyright[16]={0x43,0x6F,0x70,0x79,0x72,0x69,0x67,0x68,0x74,0x20,0x20,0x20,0x76,0x31,0x2E,0x32};
 char GTMBU[16]={0x20,0x20,0xB6,0xAB,0xD6,0xA5,0xB0,0xD7,0xD4,0xC6,0xC1,0xE2,0xBB,0xFA,0x20,0x20};
 char TEL[16]={0x54,0x65,0x6C,0x3A,0x30,0x32,0x30,0x5F,0x32,0x36,0x32,0x36,0x31,0x36,0x32,0x35};
 char FAX[16]={0x46,0x61,0x78,0x3A,0x30,0x32,0x30,0x5F,0x32,0x36,0x32,0x36,0x31,0x32,0x39,0x30};
#pragma  data:data
//////////////////////