bfin_serial_5xx.h

来自「linux 内核源代码」· C头文件 代码 · 共 153 行

#include <linux/serial.h>
#include <asm/dma.h>
#include <asm/portmux.h>

#define NR_PORTS		2

#define OFFSET_THR              0x00	/* Transmit Holding register            */
#define OFFSET_RBR              0x00	/* Receive Buffer register              */
#define OFFSET_DLL              0x00	/* Divisor Latch (Low-Byte)             */
#define OFFSET_IER              0x04	/* Interrupt Enable Register            */
#define OFFSET_DLH              0x04	/* Divisor Latch (High-Byte)            */
#define OFFSET_IIR              0x08	/* Interrupt Identification Register    */
#define OFFSET_LCR              0x0C	/* Line Control Register                */
#define OFFSET_MCR              0x10	/* Modem Control Register               */
#define OFFSET_LSR              0x14	/* Line Status Register                 */
#define OFFSET_MSR              0x18	/* Modem Status Register                */
#define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
#define OFFSET_GCTL             0x24	/* Global Control Register              */

#define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
#define UART_GET_DLL(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLL))
#define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
#define UART_GET_DLH(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLH))
#define UART_GET_IIR(uart)      bfin_read16(((uart)->port.membase + OFFSET_IIR))
#define UART_GET_LCR(uart)      bfin_read16(((uart)->port.membase + OFFSET_LCR))
#define UART_GET_LSR(uart)      bfin_read16(((uart)->port.membase + OFFSET_LSR))
#define UART_GET_GCTL(uart)     bfin_read16(((uart)->port.membase + OFFSET_GCTL))

#define UART_PUT_CHAR(uart,v)   bfin_write16(((uart)->port.membase + OFFSET_THR),v)
#define UART_PUT_DLL(uart,v)    bfin_write16(((uart)->port.membase + OFFSET_DLL),v)
#define UART_PUT_IER(uart,v)    bfin_write16(((uart)->port.membase + OFFSET_IER),v)
#define UART_PUT_DLH(uart,v)    bfin_write16(((uart)->port.membase + OFFSET_DLH),v)
#define UART_PUT_LCR(uart,v)    bfin_write16(((uart)->port.membase + OFFSET_LCR),v)
#define UART_PUT_GCTL(uart,v)   bfin_write16(((uart)->port.membase + OFFSET_GCTL),v)

#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS)
# define CONFIG_SERIAL_BFIN_CTSRTS

# ifndef CONFIG_UART0_CTS_PIN
#  define CONFIG_UART0_CTS_PIN -1
# endif

# ifndef CONFIG_UART0_RTS_PIN
#  define CONFIG_UART0_RTS_PIN -1
# endif

# ifndef CONFIG_UART1_CTS_PIN
#  define CONFIG_UART1_CTS_PIN -1
# endif

# ifndef CONFIG_UART1_RTS_PIN
#  define CONFIG_UART1_RTS_PIN -1
# endif
#endif
/*
 * The pin configuration is different from schematic
 */
struct bfin_serial_port {
        struct uart_port        port;
        unsigned int            old_status;
#ifdef CONFIG_SERIAL_BFIN_DMA
	int			tx_done;
	int			tx_count;
	struct circ_buf		rx_dma_buf;
	struct timer_list       rx_dma_timer;
	int			rx_dma_nrows;
	unsigned int		tx_dma_channel;
	unsigned int		rx_dma_channel;
	struct work_struct	tx_dma_workqueue;
#else
	struct work_struct 	cts_workqueue;
#endif
#ifdef CONFIG_SERIAL_BFIN_CTSRTS
	int		cts_pin;
	int 		rts_pin;
#endif
};

struct bfin_serial_port bfin_serial_ports[NR_PORTS];
struct bfin_serial_res {
	unsigned long	uart_base_addr;
	int		uart_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
	unsigned int	uart_tx_dma_channel;
	unsigned int	uart_rx_dma_channel;
#endif
#ifdef CONFIG_SERIAL_BFIN_CTSRTS
	int	uart_cts_pin;
	int	uart_rts_pin;
#endif
};

struct bfin_serial_res bfin_serial_resource[] = {
#ifdef CONFIG_SERIAL_BFIN_UART0
	{
	0xFFC00400,
	IRQ_UART0_RX,
#ifdef CONFIG_SERIAL_BFIN_DMA
	CH_UART0_TX,
	CH_UART0_RX,
#endif
#ifdef CONFIG_BFIN_UART0_CTSRTS
	CONFIG_UART0_CTS_PIN,
	CONFIG_UART0_RTS_PIN,
#endif
	},
#endif
#ifdef CONFIG_SERIAL_BFIN_UART1
	{
	0xFFC02000,
	IRQ_UART1_RX,
#ifdef CONFIG_SERIAL_BFIN_DMA
	CH_UART1_TX,
	CH_UART1_RX,
#endif
#ifdef CONFIG_BFIN_UART1_CTSRTS
	CONFIG_UART1_CTS_PIN,
	CONFIG_UART1_RTS_PIN,
#endif
	},
#endif
};

int nr_ports = ARRAY_SIZE(bfin_serial_resource);

#define DRIVER_NAME "bfin-uart"

static void bfin_serial_hw_init(struct bfin_serial_port *uart)
{

#ifdef CONFIG_SERIAL_BFIN_UART0
	peripheral_request(P_UART0_TX, DRIVER_NAME);
	peripheral_request(P_UART0_RX, DRIVER_NAME);
#endif

#ifdef CONFIG_SERIAL_BFIN_UART1
	peripheral_request(P_UART1_TX, DRIVER_NAME);
	peripheral_request(P_UART1_RX, DRIVER_NAME);
#endif

#ifdef CONFIG_SERIAL_BFIN_CTSRTS
	if (uart->cts_pin >= 0) {
		gpio_request(uart->cts_pin, DRIVER_NAME);
		gpio_direction_input(uart->cts_pin);
	}

	if (uart->rts_pin >= 0) {
		gpio_request(uart->rts_pin, DRIVER_NAME);
		gpio_direction_output(uart->rts_pin);
	}
#endif
}