spidev.c

来自「linux 内核源代码」· C语言 代码 · 共 597 行

/*
 * spidev.c -- simple synchronous userspace interface to SPI devices
 *
 * Copyright (C) 2006 SWAPP
 *	Andrea Paterniani <[e-mail]>
 * Copyright (C) 2007 David Brownell (simplification, cleanup)
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

#include <linux/init.h>
#include <linux/module.h>
#include <linux/ioctl.h>
#include <linux/fs.h>
#include <linux/device.h>
#include <linux/list.h>
#include <linux/errno.h>
#include <linux/mutex.h>
#include <linux/slab.h>

#include <linux/spi/spi.h>
#include <linux/spi/spidev.h>

#include <asm/uaccess.h>


/*
 * This supports acccess to SPI devices using normal userspace I/O calls.
 * Note that while traditional UNIX/POSIX I/O semantics are half duplex,
 * and often mask message boundaries, full SPI support requires full duplex
 * transfers.  There are several kinds of of internal message boundaries to
 * handle chipselect management and other protocol options.
 *
 * SPI has a character major number assigned.  We allocate minor numbers
 * dynamically using a bitmask.  You must use hotplug tools, such as udev
 * (or mdev with busybox) to create and destroy the /dev/spidevB.C device
 * nodes, since there is no fixed association of minor numbers with any
 * particular SPI bus or device.
 */
#define SPIDEV_MAJOR			153	/* assigned */
#define N_SPI_MINORS			32	/* ... up to 256 */

static unsigned long	minors[N_SPI_MINORS / BITS_PER_LONG];


/* Bit masks for spi_device.mode management.  Note that incorrect
 * settings for CS_HIGH and 3WIRE can cause *lots* of trouble for other
 * devices on a shared bus:  CS_HIGH, because this device will be
 * active when it shouldn't be;  3WIRE, because when active it won't
 * behave as it should.
 *
 * REVISIT should changing those two modes be privileged?
 */
#define SPI_MODE_MASK		(SPI_CPHA | SPI_CPOL | SPI_CS_HIGH \
				| SPI_LSB_FIRST | SPI_3WIRE | SPI_LOOP)

struct spidev_data {
	struct device		dev;
	struct spi_device	*spi;
	struct list_head	device_entry;

	struct mutex		buf_lock;
	unsigned		users;
	u8			*buffer;
};

static LIST_HEAD(device_list);
static DEFINE_MUTEX(device_list_lock);

static unsigned bufsiz = 4096;
module_param(bufsiz, uint, S_IRUGO);
MODULE_PARM_DESC(bufsiz, "data bytes in biggest supported SPI message");

/*-------------------------------------------------------------------------*/

/* Read-only message with current device setup */
static ssize_t
spidev_read(struct file *filp, char __user *buf, size_t count, loff_t *f_pos)
{
	struct spidev_data	*spidev;
	struct spi_device	*spi;
	ssize_t			status = 0;

	/* chipselect only toggles at start or end of operation */
	if (count > bufsiz)
		return -EMSGSIZE;

	spidev = filp->private_data;
	spi = spidev->spi;

	mutex_lock(&spidev->buf_lock);
	status = spi_read(spi, spidev->buffer, count);
	if (status == 0) {
		unsigned long	missing;

		missing = copy_to_user(buf, spidev->buffer, count);
		if (count && missing == count)
			status = -EFAULT;
		else
			status = count - missing;
	}
	mutex_unlock(&spidev->buf_lock);

	return status;
}

/* Write-only message with current device setup */
static ssize_t
spidev_write(struct file *filp, const char __user *buf,
		size_t count, loff_t *f_pos)
{
	struct spidev_data	*spidev;
	struct spi_device	*spi;
	ssize_t			status = 0;
	unsigned long		missing;

	/* chipselect only toggles at start or end of operation */
	if (count > bufsiz)
		return -EMSGSIZE;

	spidev = filp->private_data;
	spi = spidev->spi;

	mutex_lock(&spidev->buf_lock);
	missing = copy_from_user(spidev->buffer, buf, count);
	if (missing == 0) {
		status = spi_write(spi, spidev->buffer, count);
		if (status == 0)
			status = count;
	} else
		status = -EFAULT;
	mutex_unlock(&spidev->buf_lock);

	return status;
}

static int spidev_message(struct spidev_data *spidev,
		struct spi_ioc_transfer *u_xfers, unsigned n_xfers)
{
	struct spi_message	msg;
	struct spi_transfer	*k_xfers;
	struct spi_transfer	*k_tmp;
	struct spi_ioc_transfer *u_tmp;
	struct spi_device	*spi = spidev->spi;
	unsigned		n, total;
	u8			*buf;
	int			status = -EFAULT;

	spi_message_init(&msg);
	k_xfers = kcalloc(n_xfers, sizeof(*k_tmp), GFP_KERNEL);
	if (k_xfers == NULL)
		return -ENOMEM;

	/* Construct spi_message, copying any tx data to bounce buffer.
	 * We walk the array of user-provided transfers, using each one
	 * to initialize a kernel version of the same transfer.
	 */
	mutex_lock(&spidev->buf_lock);
	buf = spidev->buffer;
	total = 0;
	for (n = n_xfers, k_tmp = k_xfers, u_tmp = u_xfers;
			n;
			n--, k_tmp++, u_tmp++) {
		k_tmp->len = u_tmp->len;

		total += k_tmp->len;
		if (total > bufsiz) {
			status = -EMSGSIZE;
			goto done;
		}

		if (u_tmp->rx_buf) {
			k_tmp->rx_buf = buf;
			if (!access_ok(VERIFY_WRITE, (u8 __user *)
						(uintptr_t) u_tmp->rx_buf,
						u_tmp->len))
				goto done;
		}
		if (u_tmp->tx_buf) {
			k_tmp->tx_buf = buf;
			if (copy_from_user(buf, (const u8 __user *)
						(uintptr_t) u_tmp->tx_buf,
					u_tmp->len))
				goto done;
		}
		buf += k_tmp->len;

		k_tmp->cs_change = !!u_tmp->cs_change;
		k_tmp->bits_per_word = u_tmp->bits_per_word;
		k_tmp->delay_usecs = u_tmp->delay_usecs;
		k_tmp->speed_hz = u_tmp->speed_hz;
#ifdef VERBOSE
		dev_dbg(&spi->dev,
			"  xfer len %zd %s%s%s%dbits %u usec %uHz\n",
			u_tmp->len,
			u_tmp->rx_buf ? "rx " : "",
			u_tmp->tx_buf ? "tx " : "",
			u_tmp->cs_change ? "cs " : "",
			u_tmp->bits_per_word ? : spi->bits_per_word,
			u_tmp->delay_usecs,
			u_tmp->speed_hz ? : spi->max_speed_hz);
#endif
		spi_message_add_tail(k_tmp, &msg);
	}

	status = spi_sync(spi, &msg);
	if (status < 0)
		goto done;

	/* copy any rx data out of bounce buffer */
	buf = spidev->buffer;
	for (n = n_xfers, u_tmp = u_xfers; n; n--, u_tmp++) {
		if (u_tmp->rx_buf) {
			if (__copy_to_user((u8 __user *)
					(uintptr_t) u_tmp->rx_buf, buf,
					u_tmp->len)) {
				status = -EFAULT;
				goto done;
			}
		}
		buf += u_tmp->len;
	}
	status = total;

done:
	mutex_unlock(&spidev->buf_lock);
	kfree(k_xfers);
	return status;
}

static int
spidev_ioctl(struct inode *inode, struct file *filp,
		unsigned int cmd, unsigned long arg)
{
	int			err = 0;
	int			retval = 0;
	struct spidev_data	*spidev;
	struct spi_device	*spi;
	u32			tmp;
	unsigned		n_ioc;
	struct spi_ioc_transfer	*ioc;

	/* Check type and command number */
	if (_IOC_TYPE(cmd) != SPI_IOC_MAGIC)
		return -ENOTTY;

	/* Check access direction once here; don't repeat below.
	 * IOC_DIR is from the user perspective, while access_ok is
	 * from the kernel perspective; so they look reversed.
	 */
	if (_IOC_DIR(cmd) & _IOC_READ)
		err = !access_ok(VERIFY_WRITE,
				(void __user *)arg, _IOC_SIZE(cmd));
	if (err == 0 && _IOC_DIR(cmd) & _IOC_WRITE)
		err = !access_ok(VERIFY_READ,
				(void __user *)arg, _IOC_SIZE(cmd));
	if (err)
		return -EFAULT;

	spidev = filp->private_data;
	spi = spidev->spi;

	switch (cmd) {
	/* read requests */
	case SPI_IOC_RD_MODE:
		retval = __put_user(spi->mode & SPI_MODE_MASK,
					(__u8 __user *)arg);
		break;
	case SPI_IOC_RD_LSB_FIRST:
		retval = __put_user((spi->mode & SPI_LSB_FIRST) ?  1 : 0,
					(__u8 __user *)arg);
		break;
	case SPI_IOC_RD_BITS_PER_WORD:
		retval = __put_user(spi->bits_per_word, (__u8 __user *)arg);
		break;
	case SPI_IOC_RD_MAX_SPEED_HZ:
		retval = __put_user(spi->max_speed_hz, (__u32 __user *)arg);
		break;

	/* write requests */
	case SPI_IOC_WR_MODE:
		retval = __get_user(tmp, (u8 __user *)arg);
		if (retval == 0) {
			u8	save = spi->mode;

			if (tmp & ~SPI_MODE_MASK) {
				retval = -EINVAL;
				break;
			}

			tmp |= spi->mode & ~SPI_MODE_MASK;
			spi->mode = (u8)tmp;
			retval = spi_setup(spi);
			if (retval < 0)
				spi->mode = save;
			else
				dev_dbg(&spi->dev, "spi mode %02x\n", tmp);
		}
		break;
	case SPI_IOC_WR_LSB_FIRST:
		retval = __get_user(tmp, (__u8 __user *)arg);
		if (retval == 0) {
			u8	save = spi->mode;

			if (tmp)
				spi->mode |= SPI_LSB_FIRST;
			else
				spi->mode &= ~SPI_LSB_FIRST;
			retval = spi_setup(spi);
			if (retval < 0)
				spi->mode = save;
			else
				dev_dbg(&spi->dev, "%csb first\n",
						tmp ? 'l' : 'm');
		}
		break;
	case SPI_IOC_WR_BITS_PER_WORD:
		retval = __get_user(tmp, (__u8 __user *)arg);
		if (retval == 0) {
			u8	save = spi->bits_per_word;

			spi->bits_per_word = tmp;
			retval = spi_setup(spi);
			if (retval < 0)
				spi->bits_per_word = save;
			else
				dev_dbg(&spi->dev, "%d bits per word\n", tmp);
		}
		break;
	case SPI_IOC_WR_MAX_SPEED_HZ:
		retval = __get_user(tmp, (__u32 __user *)arg);
		if (retval == 0) {
			u32	save = spi->max_speed_hz;

			spi->max_speed_hz = tmp;
			retval = spi_setup(spi);
			if (retval < 0)
				spi->max_speed_hz = save;
			else
				dev_dbg(&spi->dev, "%d Hz (max)\n", tmp);
		}
		break;

	default:
		/* segmented and/or full-duplex I/O request */
		if (_IOC_NR(cmd) != _IOC_NR(SPI_IOC_MESSAGE(0))
				|| _IOC_DIR(cmd) != _IOC_WRITE)
			return -ENOTTY;

		tmp = _IOC_SIZE(cmd);
		if ((tmp % sizeof(struct spi_ioc_transfer)) != 0) {
			retval = -EINVAL;
			break;
		}
		n_ioc = tmp / sizeof(struct spi_ioc_transfer);
		if (n_ioc == 0)
			break;

		/* copy into scratch area */
		ioc = kmalloc(tmp, GFP_KERNEL);
		if (!ioc) {
			retval = -ENOMEM;
			break;
		}
		if (__copy_from_user(ioc, (void __user *)arg, tmp)) {
			kfree(ioc);
			retval = -EFAULT;
			break;
		}

		/* translate to spi_message, execute */
		retval = spidev_message(spidev, ioc, n_ioc);
		kfree(ioc);
		break;
	}
	return retval;
}

static int spidev_open(struct inode *inode, struct file *filp)
{
	struct spidev_data	*spidev;
	int			status = -ENXIO;

	mutex_lock(&device_list_lock);

	list_for_each_entry(spidev, &device_list, device_entry) {
		if (spidev->dev.devt == inode->i_rdev) {
			status = 0;
			break;
		}
	}
	if (status == 0) {
		if (!spidev->buffer) {
			spidev->buffer = kmalloc(bufsiz, GFP_KERNEL);
			if (!spidev->buffer) {
				dev_dbg(&spidev->spi->dev, "open/ENOMEM\n");
				status = -ENOMEM;
			}
		}
		if (status == 0) {
			spidev->users++;
			filp->private_data = spidev;
			nonseekable_open(inode, filp);
		}
	} else
		pr_debug("spidev: nothing for minor %d\n", iminor(inode));

	mutex_unlock(&device_list_lock);
	return status;
}

static int spidev_release(struct inode *inode, struct file *filp)
{
	struct spidev_data	*spidev;
	int			status = 0;

	mutex_lock(&device_list_lock);
	spidev = filp->private_data;
	filp->private_data = NULL;
	spidev->users--;
	if (!spidev->users) {
		kfree(spidev->buffer);
		spidev->buffer = NULL;
	}
	mutex_unlock(&device_list_lock);

	return status;
}

static struct file_operations spidev_fops = {
	.owner =	THIS_MODULE,
	/* REVISIT switch to aio primitives, so that userspace
	 * gets more complete API coverage.  It'll simplify things
	 * too, except for the locking.
	 */
	.write =	spidev_write,
	.read =		spidev_read,
	.ioctl =	spidev_ioctl,
	.open =		spidev_open,
	.release =	spidev_release,
};

/*-------------------------------------------------------------------------*/

/* The main reason to have this class is to make mdev/udev create the
 * /dev/spidevB.C character device nodes exposing our userspace API.
 * It also simplifies memory management.
 */

static void spidev_classdev_release(struct device *dev)
{
	struct spidev_data	*spidev;

	spidev = container_of(dev, struct spidev_data, dev);
	kfree(spidev);
}

static struct class spidev_class = {
	.name		= "spidev",
	.owner		= THIS_MODULE,
	.dev_release	= spidev_classdev_release,
};

/*-------------------------------------------------------------------------*/

static int spidev_probe(struct spi_device *spi)
{
	struct spidev_data	*spidev;
	int			status;
	unsigned long		minor;

	/* Allocate driver data */
	spidev = kzalloc(sizeof(*spidev), GFP_KERNEL);
	if (!spidev)
		return -ENOMEM;

	/* Initialize the driver data */
	spidev->spi = spi;
	mutex_init(&spidev->buf_lock);

	INIT_LIST_HEAD(&spidev->device_entry);

	/* If we can allocate a minor number, hook up this device.
	 * Reusing minors is fine so long as udev or mdev is working.
	 */
	mutex_lock(&device_list_lock);
	minor = find_first_zero_bit(minors, N_SPI_MINORS);
	if (minor < N_SPI_MINORS) {
		spidev->dev.parent = &spi->dev;
		spidev->dev.class = &spidev_class;
		spidev->dev.devt = MKDEV(SPIDEV_MAJOR, minor);
		snprintf(spidev->dev.bus_id, sizeof spidev->dev.bus_id,
				"spidev%d.%d",
				spi->master->bus_num, spi->chip_select);
		status = device_register(&spidev->dev);
	} else {
		dev_dbg(&spi->dev, "no minor number available!\n");
		status = -ENODEV;
	}
	if (status == 0) {
		set_bit(minor, minors);
		dev_set_drvdata(&spi->dev, spidev);
		list_add(&spidev->device_entry, &device_list);
	}
	mutex_unlock(&device_list_lock);

	if (status != 0)
		kfree(spidev);

	return status;
}

static int spidev_remove(struct spi_device *spi)
{
	struct spidev_data	*spidev = dev_get_drvdata(&spi->dev);

	mutex_lock(&device_list_lock);

	list_del(&spidev->device_entry);
	dev_set_drvdata(&spi->dev, NULL);
	clear_bit(MINOR(spidev->dev.devt), minors);
	device_unregister(&spidev->dev);

	mutex_unlock(&device_list_lock);

	return 0;
}

static struct spi_driver spidev_spi = {
	.driver = {
		.name =		"spidev",
		.owner =	THIS_MODULE,
	},
	.probe =	spidev_probe,
	.remove =	__devexit_p(spidev_remove),

	/* NOTE:  suspend/resume methods are not necessary here.
	 * We don't do anything except pass the requests to/from
	 * the underlying controller.  The refrigerator handles
	 * most issues; the controller driver handles the rest.
	 */
};

/*-------------------------------------------------------------------------*/

static int __init spidev_init(void)
{
	int status;

	/* Claim our 256 reserved device numbers.  Then register a class
	 * that will key udev/mdev to add/remove /dev nodes.  Last, register
	 * the driver which manages those device numbers.
	 */
	BUILD_BUG_ON(N_SPI_MINORS > 256);
	status = register_chrdev(SPIDEV_MAJOR, "spi", &spidev_fops);
	if (status < 0)
		return status;

	status = class_register(&spidev_class);
	if (status < 0) {
		unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
		return status;
	}

	status = spi_register_driver(&spidev_spi);
	if (status < 0) {
		class_unregister(&spidev_class);
		unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
	}
	return status;
}
module_init(spidev_init);

static void __exit spidev_exit(void)
{
	spi_unregister_driver(&spidev_spi);
	class_unregister(&spidev_class);
	unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
}
module_exit(spidev_exit);

MODULE_AUTHOR("Andrea Paterniani, <[e-mail]>");
MODULE_DESCRIPTION("User mode SPI device interface");
MODULE_LICENSE("GPL");