conf_usb.h

ATMEL at90usb128 usb HID source code for win-avr

//! @file conf_usb.h,v
//!
//! Copyright (c) 2006 Atmel.
//!
//! Please read file license.txt for copyright notice.
//!
//! This file contains the possible external configuration of the USB
//!
//!
//! @version 1.1 at90usb128-demo-hidgen-std-2_0_0 $Id: conf_usb.h,v 1.1 2007/01/05 12:56:56 rletendu Exp $
//!
//! @todo
//! @bug
#ifndef _CONF_USB_H_
#define _CONF_USB_H_

//! @defgroup usb_general_conf USB application configuration
//!
//! @{


   // _________________ USB MODE CONFIGURATION ____________________________
   //
   //! @defgroup USB_op_mode USB operating modes configuration
   //! defines to enable device or host usb operating modes
   //! supported by the application
   //! @{

      //! @brief ENABLE to activate the host software library support
      //!
      //! Possible values ENABLE or DISABLE
      #define USB_HOST_FEATURE            DISABLED

      //! @brief ENABLE to activate the device software library support
      //!
      //! Possible values ENABLE or DISABLE
      #define USB_DEVICE_FEATURE          ENABLED

   //! @}

   // _________________ USB REGULATOR CONFIGURATION _______________________
   //
   //! @defgroup USB_reg_mode USB regulator configuration
   //! @{

   //! @brief Enable the internal regulator for USB pads
   //!
   //! When the application voltage is lower than 3.5V, to optimize power consumption
   //! the internal USB pads regulatr can be disabled.
#ifndef USE_USB_PADS_REGULATOR
   #define USE_USB_PADS_REGULATOR   ENABLE      // Possible values ENABLE or DISABLE
#endif
   //! @}

   // _________________ HOST MODE CONFIGURATION ____________________________
   //
   //! @defgroup USB_host_mode_cfg USB host operating mode configuration
   //!
   //! @{

   #define HID_CLASS          0x03
   #define MS_CLASS           0x08

   //!   @brief VID/PID supported table list
   //!
   //!   This table contains the VID/PID that are supported by the reduced host application
   //!   VID_PID_TABLE format definition:
   //!
   //!   #define VID_PID_TABLE      {VID1, number_of_pid_for_this_VID1, PID11_value,..., PID1X_Value \n
   //!                              ...\n
   //!                              ,VIDz, number_of_pid_for_this_VIDz, PIDz1_value,..., PIDzX_Value}
   #define VID_PID_TABLE            {0x03EB, 2, 0x201C, 0x2014 \
                                    ,0x0123, 3, 0x2000, 0x2100, 0x1258}

   //!   @brief CLASS/SUBCLASS_PROTOCOL supported table list
   //!
   //!   This table contains the CLASS/SUBCLASS/PROTOCOL that is supported by the reduced host application
   //!   This table definition allows to extended the reduced application device support to an entire Class/
   //!   /subclass/protocol instead of a simple VID/PID table list.
   //!
   //!   CLASS_SUBCLASS_PROTOCOL format definition: \n
   //!   #define CLASS_SUBCLASS_PROTOCOL  {CLASS1, SUB_CLASS1,PROTOCOL1, \n
   //!                                     ...\n
   //!                                     CLASSz, SUB_CLASSz,PROTOCOLz}
   #define CLASS_SUBCLASS_PROTOCOL     {0x0A, 0x00, 0x00, \
                                       0x00, 0x00, 0x00,\
                                       0xFF,0x00,0x00}

   //! The size of RAM buffer reserved of descriptors manipulation
   #define SIZEOF_DATA_STAGE        250

   //! The address that will be assigned to the connected device
   #define DEVICE_ADDRESS           0x05

   //! The host controller will be limited to the strict VID/PID list.
   //! When enabled, if the device PID/VID does not belongs  to the supported list,
   //! the host controller library will not go to deeper configuration, but to error state.
   #define HOST_STRICT_VID_PID_TABLE      DISABLE

   //! Try to configure the host pipe according to the device descriptors received
   #define HOST_AUTO_CFG_ENDPOINT         ENABLE

   //! Host start of frame interrupt always enable
   #define HOST_CONTINUOUS_SOF_INTERRUPT  DISABLE

   //! When Host error state detected, goto unattached state
   #define HOST_ERROR_RESTART             ENABLE

   //! Force WDT reset upon ID pin change
   #define ID_PIN_CHANGE_GENERATE_RESET   DISABLE

   //! NAK handshake in 1/4sec (250ms) before timeout
   #define NAK_TIMEOUT_DELAY              1

   #if (HOST_AUTO_CFG_ENDPOINT==FALSE)
      //! If no auto configuration of EP, map here user function
      #define        User_configure_endpoint()
   #endif

   //! @defgroup host_cst_actions USB host custom actions
   //!
   //! @{
   // write here the action to associate to each USB host event
   // be carefull not to waste time in order not disturbing the functions
   #define Usb_id_transition_action()
   #define Host_device_disconnection_action()
   #define Host_device_connection_action()
   #define Host_sof_action()
   #define Host_suspend_action()                      host_suspend_action();
   #define Host_hwup_action()
   #define Host_device_not_supported_action()
   #define Host_device_supported_action()
   #define Host_device_error_action()
   //! @}

extern void host_suspend_action(void);
   //! @}


// _________________ DEVICE MODE CONFIGURATION __________________________

   //! @defgroup USB_device_mode_cfg USB device operating mode configuration
   //!
   //! @{
      
#define Usb_unicode(a)			((U16)(a))      

#define NB_ENDPOINTS          2  // number of endpoints in the application
#define EP_HID_IN             1
#define EP_HID_OUT            2



   //! @defgroup device_cst_actions USB device custom actions
   //!
   //! @{
   // write here the action to associate to each USB event
   // be carefull not to waste time in order not disturbing the functions
#define Usb_sof_action()         sof_action();
#define Usb_wake_up_action()
#define Usb_resume_action()
#define Usb_suspend_action()
#define Usb_reset_action()
#define Usb_vbus_on_action()
#define Usb_vbus_off_action()
#define Usb_set_configuration_action()
   //! @}

extern void sof_action(void);
   //! @}

//! @}

#endif // _CONF_USB_H_