hal_diag.c

开放源码实时操作系统源码.

//=============================================================================
//
//      hal_diag.c
//
//      HAL diagnostic I/O code
//
//=============================================================================
//####ECOSGPLCOPYRIGHTBEGIN####
// -------------------------------------------
// This file is part of eCos, the Embedded Configurable Operating System.
// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
// Copyright (C) 2002, 2003 Gary Thomas
//
// eCos is free software; you can redistribute it and/or modify it under
// the terms of the GNU General Public License as published by the Free
// Software Foundation; either version 2 or (at your option) any later version.
//
// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
// WARRANTY; without even the implied warranty of MERCHANTABILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// You should have received a copy of the GNU General Public License along
// with eCos; if not, write to the Free Software Foundation, Inc.,
// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
//
// As a special exception, if other files instantiate templates or use macros
// or inline functions from this file, or you compile this file and link it
// with other works to produce a work based on this file, this file does not
// by itself cause the resulting work to be covered by the GNU General Public
// License. However the source code for this file must still be made available
// in accordance with section (3) of the GNU General Public License.
//
// This exception does not invalidate any other reasons why a work based on
// this file might be covered by the GNU General Public License.
//
// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
// at http://sources.redhat.com/ecos/ecos-license/
// -------------------------------------------
//####ECOSGPLCOPYRIGHTEND####
//=============================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):   hmt
// Contributors:hmt, gthomas
// Date:        1999-06-08
// Purpose:     HAL diagnostic output
// Description: Implementations of HAL diagnostic I/O support.
//
//####DESCRIPTIONEND####
//
//=============================================================================

#include <pkgconf/hal.h>

#include <cyg/infra/cyg_type.h>         // base types
#include <cyg/infra/cyg_trac.h>         // tracing macros
#include <cyg/infra/cyg_ass.h>          // assertion macros

#include <cyg/hal/hal_io.h>             // IO macros
#include <cyg/hal/hal_diag.h>
#include <cyg/hal/hal_misc.h>           // cyg_hal_is_break()
#include <cyg/hal/hal_intr.h>           // Interrupt macros
#include <cyg/hal/drv_api.h>

#if defined(CYGDBG_HAL_DEBUG_GDB_INCLUDE_STUBS)
#include <cyg/hal/hal_stub.h>           // hal_output_gdb_string
#endif

#include <cyg/hal/ppc_regs.h>

//=============================================================================
// Serial driver
//=============================================================================

//-----------------------------------------------------------------------------
// There are two serial ports.
#define CYG_DEV_SERIAL_BASE_A    0xF0004500 // port A
#define CYG_DEV_SERIAL_BASE_B    0xF0004600 // port B

//-----------------------------------------------------------------------------
// Default baud rate is 38400
#define _MEMCLK (CYGHWR_HAL_POWERPC_MEM_SPEED*1000000)
#define _BAUD   CYGNUM_HAL_VIRTUAL_VECTOR_CONSOLE_CHANNEL_BAUD
#define CYG_DEV_SERIAL_RS232_T1_VALUE_B38400  (((_MEMCLK/16)/_BAUD) >> 8)
#define CYG_DEV_SERIAL_RS232_T2_VALUE_B38400  (((_MEMCLK/16)/_BAUD) & 0xFF)

//-----------------------------------------------------------------------------
// Define the serial registers. The 8245 has a 16552 UART builtin.
//
#define CYG_DEV_SERIAL_RBR   0x00  // receiver buffer register, read, dlab = 0
#define CYG_DEV_SERIAL_THR   0x00 // transmitter holding register, write, dlab = 0
#define CYG_DEV_SERIAL_DLL   0x00 // divisor latch (LS), read/write, dlab = 1
#define CYG_DEV_SERIAL_IER   0x01 // interrupt enable register, read/write, dlab = 0
#define CYG_DEV_SERIAL_DLM   0x01 // divisor latch (MS), read/write, dlab = 1
#define CYG_DEV_SERIAL_IIR   0x02 // interrupt identification register, read, dlab = 0
#define CYG_DEV_SERIAL_FCR   0x02 // fifo control register, write, dlab = 0
#define CYG_DEV_SERIAL_AFR   0x02 // alternate function register, read/write, dlab = 1
#define CYG_DEV_SERIAL_LCR   0x03 // line control register, read/write
#define CYG_DEV_SERIAL_MCR   0x04
#define CYG_DEV_SERIAL_MCR_A 0x04
#define CYG_DEV_SERIAL_MCR_B 0x04
#define CYG_DEV_SERIAL_LSR   0x05 // line status register, read
#define CYG_DEV_SERIAL_MSR   0x06 // modem status register, read
#define CYG_DEV_SERIAL_SCR   0x07 // scratch pad register
#define CYG_DEV_SERIAL_DCR   0x11 // device control (UART vs DUART)

// The interrupt enable register bits.
#define SIO_IER_ERDAI   0x01            // enable received data available irq
#define SIO_IER_ETHREI  0x02            // enable THR empty interrupt
#define SIO_IER_ELSI    0x04            // enable receiver line status irq
#define SIO_IER_EMSI    0x08            // enable modem status interrupt

// The interrupt identification register bits.
#define SIO_IIR_IP      0x01            // 0 if interrupt pending
#define SIO_IIR_ID_MASK 0x0e            // mask for interrupt ID bits
#define ISR_Tx  0x02
#define ISR_Rx  0x04

// The line status register bits.
#define SIO_LSR_DR      0x01            // data ready
#define SIO_LSR_OE      0x02            // overrun error
#define SIO_LSR_PE      0x04            // parity error
#define SIO_LSR_FE      0x08            // framing error
#define SIO_LSR_BI      0x10            // break interrupt
#define SIO_LSR_THRE    0x20            // transmitter holding register empty
#define SIO_LSR_TEMT    0x40            // transmitter register empty
#define SIO_LSR_ERR     0x80            // any error condition

// The modem status register bits.
#define SIO_MSR_DCTS  0x01              // delta clear to send
#define SIO_MSR_DDSR  0x02              // delta data set ready
#define SIO_MSR_TERI  0x04              // trailing edge ring indicator
#define SIO_MSR_DDCD  0x08              // delta data carrier detect
#define SIO_MSR_CTS   0x10              // clear to send
#define SIO_MSR_DSR   0x20              // data set ready
#define SIO_MSR_RI    0x40              // ring indicator
#define SIO_MSR_DCD   0x80              // data carrier detect

// The line control register bits.
#define SIO_LCR_WLS0   0x01             // word length select bit 0
#define SIO_LCR_WLS1   0x02             // word length select bit 1
#define SIO_LCR_STB    0x04             // number of stop bits
#define SIO_LCR_PEN    0x08             // parity enable
#define SIO_LCR_EPS    0x10             // even parity select
#define SIO_LCR_SP     0x20             // stick parity
#define SIO_LCR_SB     0x40             // set break
#define SIO_LCR_DLAB   0x80             // divisor latch access bit

// The FIFO control register
#define SIO_FCR_FEN    0x01             // enable xmit and rcvr fifos
#define SIO_FCR_RFR    0x02             // clear RCVR FIFO
#define SIO_FCR_TFR    0x04             // clear XMIT FIFO

// DUART control
#define SIO_DCR_SDM    0x01             // Special DUART mode


//-----------------------------------------------------------------------------
typedef struct {
    cyg_uint8* base;
    cyg_int32 msec_timeout;
    int isr_vector;
} channel_data_t;

//-----------------------------------------------------------------------------
static void
init_serial_channel(const channel_data_t* __ch_data)
{
    cyg_uint8* base = __ch_data->base;
    cyg_uint8 lcr, iir;

    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_IER, 0);

    // Disable and clear FIFOs (need to enable to clear).
    HAL_READ_UINT8(base+CYG_DEV_SERIAL_IIR, iir);
    if ((iir & 0xC0) == 0) {
        HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_FCR, (SIO_FCR_FEN | SIO_FCR_RFR | SIO_FCR_TFR));
        HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_FCR, 0);
    }

    // 8-1-no parity.
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_LCR, SIO_LCR_WLS0 | SIO_LCR_WLS1);

    // Set speed to 38400.
    HAL_READ_UINT8(base+CYG_DEV_SERIAL_LCR, lcr);
    lcr |= SIO_LCR_DLAB;
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_LCR, lcr);


    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_DLL,
                    CYG_DEV_SERIAL_RS232_T2_VALUE_B38400);
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_DLM,
                    CYG_DEV_SERIAL_RS232_T1_VALUE_B38400);
    lcr &= ~SIO_LCR_DLAB;
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_LCR, lcr);

    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_DCR, SIO_DCR_SDM);

    // Enable FIFOs (and clear them).
    if ((iir & 0xC0) == 0) {
        HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_FCR, (SIO_FCR_FEN | SIO_FCR_RFR | SIO_FCR_TFR));
    }
}

static void
cyg_hal_plf_serial_error(void *__ch_data, cyg_uint8 lsr)
{
    // Ignore?
}

static cyg_bool
cyg_hal_plf_serial_getc_nonblock(void* __ch_data, cyg_uint8* ch)
{
    cyg_uint8* base = ((channel_data_t*)__ch_data)->base;
    cyg_uint8 lsr;

    HAL_READ_UINT8(base+CYG_DEV_SERIAL_LSR, lsr);
    if ((lsr & SIO_LSR_ERR) != 0) {
        cyg_hal_plf_serial_error(__ch_data, lsr);
    }
    if ((lsr & SIO_LSR_DR) == 0)
        return false;

    HAL_READ_UINT8(base+CYG_DEV_SERIAL_RBR, *ch);

    return true;
}