dif_stack.m

用matlab语言写的地震偏移成像软件集,很有用的东东呵

%  DIF_STACK: create a diffraction stack from vrms(x,t) and a ZOS image
%
%  Diffraction stack algorithm with averaging and cosine weighting parameter
%  choices. A version with fewer parameter choices is available as
%  difstack_simp.m
%
%  This function takes in a ZOS exploding reflector image and sums along
%  hyperbolas T^2=T0^2+4x^2/V^2 where V=vrms(x,t) and T0= the time position
%  of the current sample. the output is the migrated stack.
%
%  This code is based upon the algorithm of J. Bancroft pg 4.14 in his book
%  "A Practical Understanding of Pre and Post Stack Migration" (2006)
%
%  [migdata,tsamp,xsamp]=dif_stack(ERM_seis,vrmsmat,dt,dx,params)
%
%  ERM_seis.....the input exploding reflector model
%  vrmsmat......RMS velocities Vrms(x,t) from vz2vt from 2way times
%  dt...........time sample rate (eg.  0.0005)
%  dx...........spatial sample rate(eg.  5)
%               these should co-respond to the values used to build
%               the velocity model and the ZOS image
%
%  migdata......the migrated seismic stack
%  xsamp........is the vector of horizontal grid positions for V(x,t),Vrms(x,t)
%  tsamp........is the vector of timesamples used for V(x,t), Vrms(x,t)
%  params.......a vector of 2 parameter choices for the diffraction stack
%               [params(1),params(2)]
%  params(1)....controls whether or not a weight factor T_0/T is applied to
%               the summed amplitude  = 1 if weighted, = 0 if not(default=1)
%  params(2)....controls whether or not a the sum of the amplitudes is
%               averaged by the number of samples in the arpeture
%               = 1 for averaging, = 0 for no averaging (default =1)
%
%  Zoron Rodriguez, John C. Bancroft,  November 2007
%
% NOTE: It is illegal for you to use this software for a purpose other
% than non-profit education or research UNLESS you are employed by a CREWES
% Project sponsor. By using this software, you are agreeing to the terms
% detailed in this software's Matlab source file.

% BEGIN TERMS OF USE LICENSE
% This SOFTWARE is maintained by the CREWES Project at the Department
% of Geology and Geophysics of the University of Calgary, Calgary,
% Alberta, Canada.  The copyright and ownership is jointly held by
% its author (identified above) and the CREWES Project.  The CREWES
% project may be contacted via email at:  [e-mail]
%
% The term 'SOFTWARE' refers to the Matlab source code, translations to
% any other computer language, or object code
%
% Terms of use of this SOFTWARE
%
% 1) Use of this SOFTWARE by any for-profit commercial organization is
%    expressly forbidden unless said organization is a CREWES Project
%    Sponsor.
%
% 2) A CREWES Project sponsor may use this SOFTWARE under the terms of the
%    CREWES Project Sponsorship agreement.
%
% 3) A student or employee of a non-profit educational institution may
%    use this SOFTWARE subject to the following terms and conditions:
%    - this SOFTWARE is for teaching or research purposes only.
%    - this SOFTWARE may be distributed to other students or researchers
%      provided that these license terms are included.
%    - reselling the SOFTWARE, or including it or any portion of it, in any
%      software that will be resold is expressly forbidden.
%    - transfering the SOFTWARE in any form to a commercial firm or any
%      other for-profit organization is expressly forbidden.
%
% END TERMS OF USE LICENSE

function [migdata,tsamp,xsamp]=dif_stack(seis1,vrmsmat,dt,dx,params)

if(nargin<5)
   params=zeros(1,2);
   params(1)=1; % set default parameter for cosine weighting
   params(2)=1; % set default parameter for
end
if (nargin<4)
  error('Not enough inputs, type help difstack and re-read instructions');
end
[vt,vx]=size(vrmsmat);
[st,sx]=size(seis1);
if ([vt,vx]~=[st,sx])
   error (' RMS velocity matrix must have the same dimensions as the exploding reflector model both in columns (traces) and rows (time samples)')
end

if (params(1)~=1&params(1)~=0)
   error(' choose params(1) as 1 for cosine weighting or 0 for no weighting type help difstack for help')
end
if (params(2)~=1&params(2)~=0)
   error(' choose params(2) as 1 for amplitude averaging or 0 for no averaging type help difstack for help')
end

migdata=zeros(size(vrmsmat));  % creat a storage array for the migrated section
A=sx;   % arperture for sumation
xsamp=dx*(0:vx-1); %return for plotting
tsamp=dt*(0:vt-1); %return for plotting

%%%%%%%%%%%%%%%%%%%%%%%%Migration Loops%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%  4 loops, similar in content but differ depending on the choice of
%  averaging and wieghting parameters params(1) and params(2)
%  runs faster this way rather than checking conditions in the loop
%  which runs much slower.  It is better to set the parameters before
%  starting the loop.
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
if params(1)==1&params(2)==1   %averaging and weighting
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
t_migloop=clock;  %get the current time before migration starts
disp('Migrating data by diffraction stack method')
for t=1:vx      %loop over traces
    t_trace=clock;  % get clock time for the current trace
     for s=1:vt   %loop over samples in the trace
        V=vrmsmat(s,t); % grab the local vrms at that position
        To=s*dt;       %define diffaction apex time
        sum=0;         %initialize sum
        count=0;       % counter for averaging the value of the sum by the number of samples in the sum
        for n=-A:A  % loop over the migration aperture
            x=n*dx; % move out by n steps
            T=sqrt((To)^2+(2*x/V)^2); % calculate the time T at movout x
            m=round(T/dt); % take the floor or ceilling of this point as the time sample position to take
            k=t+n;  %start at the trace + the moveout number of samples
            if (m<vt&k>0&k<=sx) %check bounds
                    W=To/T;    %weight the value of the diffraction point
                sum=sum+W*seis1(m,k);  %cumulative sum
            end
            count=count+1;  % increment the counter of the number of samples  in the sum
        end

            migdata(s,t)=sum/count; %put the sum at the apex of the diffraction and average by the number of samples in the sum
     end
       if (t==1|t==10|rem(t,25)==0)
         t_elapsed=etime(clock,t_migloop); %  get the elapsed time
         disp(['Positions migrated for Trace ', num2str(t), ' of ', num2str(vx), '  total time elapsed is ', num2str(t_elapsed),' seconds with ', num2str((vx/t-1)*t_elapsed),' seconds remaining']);
       end
end

t_elapsed=etime(clock,t_migloop); %  get the elapsed time
disp(['Diffraction stack migration completed in ', num2str(t_elapsed),' seconds']);
end
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
if params(1)==0 & params(2)==1    % no weighting but averaging
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
t_migloop=clock;  %get the current time before migration starts
disp('Migrating data by diffraction stack method')
for t=1:vx      %loop over traces
    t_trace=clock;  % get clock time for the current trace
        for s=1:vt   %loop over samples in the trace
        V=vrmsmat(s,t); % grab the local vrms at that position
        To=s*dt;       %define diffaction apex time
        sum=0;         %initialize sum
        count=0;       % counter for averaging the value of the sum by the number of samples in the sum
        for n=-A:A  % loop over the migration aperture
            x=n*dx; % move out by n steps
            T=sqrt((To)^2+(2*x/V)^2); % calculate the time T at movout x
            m=round(T/dt); % take the floor or ceilling of this point as the time sample position to take
            k=t+n;  %start at the trace + the moveout number of samples
            if (m<vt&k>0&k<=sx) %check bounds
                    %W=To/T;    %weight the value of the diffraction point
                    W=1; % no weighting
                    sum=sum+W*seis1(m,k);  %cumulative sum
            end
            count=count+1;  % increment the counter of the number of samples  in the sum
        end

            migdata(s,t)=sum/count; %put the sum at the apex of the diffraction and average by the number of samples in the sum
     end
       if (t==1|t==10|rem(t,25)==0)
         t_elapsed=etime(clock,t_migloop); %  get the elapsed time
         disp(['Positions migrated for Trace ', num2str(t), ' of ', num2str(vx), '  total time elapsed is ', num2str(t_elapsed),' seconds with ', num2str((vx/t-1)*t_elapsed),' seconds remaining']);
       end
end

t_elapsed=etime(clock,t_migloop); %  get the elapsed time
disp(['Diffraction stack migration completed in ', num2str(t_elapsed),' seconds']);
end
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
if params(1)==0 & params(2)==0    % no weighting and no averaging
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
t_migloop=clock;  %get the current time before migration starts
disp('Migrating data by diffraction stack method')
for t=1:vx      %loop over traces
    t_trace=clock;  % get clock time for the current trace
        for s=1:vt   %loop over samples in the trace
        V=vrmsmat(s,t); % grab the local vrms at that position
        To=s*dt;       %define diffaction apex time
        sum=0;         %initialize sum
        count=0;       % counter for averaging the value of the sum by the number of samples in the sum
        for n=-A:A  % loop over the migration aperture
            x=n*dx; % move out by n steps
            T=sqrt((To)^2+(2*x/V)^2); % calculate the time T at movout x
            m=round(T/dt); % take the floor or ceilling of this point as the time sample position to take
            k=t+n;  %start at the trace + the moveout number of samples
            if (m<vt&k>0&k<=sx) %check bounds
                %W=To/T;    %weight the value of the diffraction point
                W=1; % no weighting

                sum=sum+W*seis1(m,k);  %cumulative sum
            end
            %count=count+1;  % increment the counter of the number of samples  in the sum
        end

            migdata(s,t)=sum;        %put the sum at the apex of the diffraction
     end
       if (t==1|t==10|rem(t,25)==0)
         t_elapsed=etime(clock,t_migloop); %  get the elapsed time
         disp(['Positions migrated for Trace ', num2str(t), ' of ', num2str(vx), '  total time elapsed is ', num2str(t_elapsed),' seconds with ', num2str((vx/t-1)*t_elapsed),' seconds remaining']);
       end
end

t_elapsed=etime(clock,t_migloop); %  get the elapsed time
disp(['Diffraction stack migration completed in ', num2str(t_elapsed),' seconds']);

end
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
if params(1)==1 & params(2)==0    %  weighting and no averaging
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
t_migloop=clock;  %get the current time before migration starts
disp('Migrating data by diffraction stack method')
for t=1:vx      %loop over traces
    t_trace=clock;  % get clock time for the current trace
    for s=1:vt   %loop over samples in the trace
        V=vrmsmat(s,t); % grab the local vrms at that position
        To=s*dt;       %define diffaction apex time
        sum=0;         %initialize sum
        count=0;       % counter for averaging the value of the sum by the number of samples in the sum
        for n=-A:A  % loop over the migration aperture
            x=n*dx; % move out by n steps
            T=sqrt((To)^2+(2*x/V)^2); % calculate the time T at movout x
            m=round(T/dt); % take the floor or ceilling of this point as the time sample position to take
            k=t+n;  %start at the trace + the moveout number of samples
            if (m<vt&k>0&k<=sx) %check bounds
                    W=To/T;    %weight the value of the diffraction point
                    %W=1; % no weighting

                    sum=sum+W*seis1(m,k);  %cumulative sum
            end
            %count=count+1;  % increment the counter of the number of samples  in the sum
        end

            migdata(s,t)=sum;        %put the sum at the apex of the diffraction
     end
       if (t==1|t==10|rem(t,25)==0)
         t_elapsed=etime(clock,t_migloop); %  get the elapsed time
         disp(['Positions migrated for Trace ', num2str(t), ' of ', num2str(vx), '  total time elapsed is ', num2str(t_elapsed),' seconds with ', num2str((vx/t-1)*t_elapsed),' seconds remaining']);
       end
end

t_elapsed=etime(clock,t_migloop); %  get the elapsed time
disp(['Diffraction stack migration completed in ', num2str(t_elapsed),' seconds']);

end