example_2833xgpiosetup.c

TI公司TMS320F2883x浮点DSP的详细应用例程

// TI File $Revision: /main/8 $
// Checkin $Date: August 10, 2007   09:05:39 $
//###########################################################################
//
// FILE:    Example_2833xGpioSetup.c
//
// TITLE:   DSP2833x Device GPIO Setup
//
// ASSUMPTIONS:
//
//    This program requires the DSP2833x header files.
//
//    Two different examples are included. Select the example
//    to execute before compiling using the #define statements
//    found at the top of the code.
//
//    As supplied, this project is configured for "boot to SARAM"
//    operation.  The 2833x Boot Mode table is shown below.
//    For information on configuring the boot mode of an eZdsp,
//    please refer to the documentation included with the eZdsp,
//
//       $Boot_Table:
//
//         GPIO87   GPIO86     GPIO85   GPIO84
//          XA15     XA14       XA13     XA12
//           PU       PU         PU       PU
//        ==========================================
//            1        1          1        1    Jump to Flash
//            1        1          1        0    SCI-A boot
//            1        1          0        1    SPI-A boot
//            1        1          0        0    I2C-A boot
//            1        0          1        1    eCAN-A boot
//            1        0          1        0    McBSP-A boot
//            1        0          0        1    Jump to XINTF x16
//            1        0          0        0    Jump to XINTF x32
//            0        1          1        1    Jump to OTP
//            0        1          1        0    Parallel GPIO I/O boot
//            0        1          0        1    Parallel XINTF boot
//            0        1          0        0    Jump to SARAM	    <- "boot to SARAM"
//            0        0          1        1    Branch to check boot mode
//            0        0          1        0    Boot to flash, bypass ADC cal
//            0        0          0        1    Boot to SARAM, bypass ADC cal
//            0        0          0        0    Boot to SCI-A, bypass ADC cal
//                                              Boot_Table_End$
//
// DESCRIPTION:
//
//
//    Configures the 2833x GPIO into two different configurations
//    This code is verbose to illustrate how the GPIO could be setup.
//    In a real application, lines of code can be combined for improved
//    code size and efficency.
//
//    This example only sets-up the GPIO.. nothing is actually done with
//    the pins after setup.
//
//    In general:
//
//       All pullup resistors are enabled.  For ePWMs this may not be desired.
//       Input qual for communication ports (eCAN, SPI, SCI, I2C) is asynchronous
//       Input qual for Trip pins (TZ) is asynchronous
//       Input qual for eCAP and eQEP signals is synch to SYSCLKOUT
//       Input qual for some I/O's and interrupts may have a sampling window
//
//
//###########################################################################
// $TI Release: DSP2833x Header Files V1.01 $
// $Release Date: September 26, 2007 $
//###########################################################################

#include "DSP2833x_Device.h"     // DSP2833x Headerfile Include File
#include "DSP2833x_Examples.h"   // DSP2833x Examples Include File

// Select the example to compile in.  Only one example should be set as 1
// the rest should be set as 0.

#define EXAMPLE1 1  // Basic pinout configuration example
#define EXAMPLE2 0  // Communication pinout example

// Prototype statements for functions found within this file.
void Gpio_setup1(void);
void Gpio_setup2(void);

void main(void)
{

// Step 1. Initialize System Control:
// PLL, WatchDog, enable Peripheral Clocks
// This example function is found in the DSP2833x_SysCtrl.c file.
   InitSysCtrl();

// Step 2. Initalize GPIO:
// This example function is found in the DSP2833x_Gpio.c file and
// illustrates how to set the GPIO to it's default state.
   // InitGpio(); Skipped for this example

// Step 3. Clear all interrupts and initialize PIE vector table:
// Disable CPU interrupts
   DINT;

// Initialize PIE control registers to their default state.
// The default state is all PIE interrupts disabled and flags
// are cleared.
// This function is found in the DSP2833x_PieCtrl.c file.
   InitPieCtrl();

// Disable CPU interrupts and clear all CPU interrupt flags:
   IER = 0x0000;
   IFR = 0x0000;

// Initialize the PIE vector table with pointers to the shell Interrupt
// Service Routines (ISR).
// This will populate the entire table, even if the interrupt
// is not used in this example.  This is useful for debug purposes.
// The shell ISR routines are found in DSP2833x_DefaultIsr.c.
// This function is found in DSP2833x_PieVect.c.
   InitPieVectTable();


// Step 4. Initialize all the Device Peripherals:
// This function is found in DSP2833x_InitPeripherals.c
// InitPeripherals(); // Not required for this example

// Step 5. User specific code:

#if EXAMPLE1

    // This example is a basic pinout
    Gpio_setup1();

#endif  // - EXAMPLE1

#if EXAMPLE2

    // This example is a communications pinout
    Gpio_setup2();

#endif

}


void Gpio_setup1(void)
{
   // Example 1:
   // Basic Pinout.
   // This basic pinout includes:
   // PWM1-3, ECAP1, ECAP2, TZ1-TZ4, SPI-A, EQEP1, SCI-A, I2C
   // and a number of I/O pins

   // These can be combined into single statements for improved
   // code efficiency.

   // Enable PWM1-3 on GPIO0-GPIO5
   EALLOW;
   GpioCtrlRegs.GPAPUD.bit.GPIO0 = 0;   // Enable pullup on GPIO0
   GpioCtrlRegs.GPAPUD.bit.GPIO1 = 0;   // Enable pullup on GPIO1
   GpioCtrlRegs.GPAPUD.bit.GPIO2 = 0;   // Enable pullup on GPIO2
   GpioCtrlRegs.GPAPUD.bit.GPIO3 = 0;   // Enable pullup on GPIO3
   GpioCtrlRegs.GPAPUD.bit.GPIO4 = 0;   // Enable pullup on GPIO4
   GpioCtrlRegs.GPAPUD.bit.GPIO5 = 0;   // Enable pullup on GPIO5
   GpioCtrlRegs.GPAMUX1.bit.GPIO0 = 1;  // GPIO0 = PWM1A
   GpioCtrlRegs.GPAMUX1.bit.GPIO1 = 1;  // GPIO1 = PWM1B
   GpioCtrlRegs.GPAMUX1.bit.GPIO2 = 1;  // GPIO2 = PWM2A
   GpioCtrlRegs.GPAMUX1.bit.GPIO3 = 1;  // GPIO3 = PWM2B
   GpioCtrlRegs.GPAMUX1.bit.GPIO4 = 1;  // GPIO4 = PWM3A
   GpioCtrlRegs.GPAMUX1.bit.GPIO5 = 1;  // GPIO5 = PWM3B

   // Enable an GPIO output on GPIO6, set it high
   GpioCtrlRegs.GPAPUD.bit.GPIO6 = 0;   // Enable pullup on GPIO6
   GpioDataRegs.GPASET.bit.GPIO6 = 1;   // Load output latch
   GpioCtrlRegs.GPAMUX1.bit.GPIO6 = 0;  // GPIO6 = GPIO6
   GpioCtrlRegs.GPADIR.bit.GPIO6 = 1;   // GPIO6 = output

   // Enable eCAP1 on GPIO7
   GpioCtrlRegs.GPAPUD.bit.GPIO7 = 0;   // Enable pullup on GPIO7
   GpioCtrlRegs.GPAQSEL1.bit.GPIO7 = 0; // Synch to SYSCLOUT
   GpioCtrlRegs.GPAMUX1.bit.GPIO7 = 3;  // GPIO7 = ECAP2

   // Enable GPIO outputs on GPIO8 - GPIO11, set it high
   GpioCtrlRegs.GPAPUD.bit.GPIO8 = 0;   // Enable pullup on GPIO8
   GpioDataRegs.GPASET.bit.GPIO8 = 1;   // Load output latch
   GpioCtrlRegs.GPAMUX1.bit.GPIO8 = 0;  // GPIO8 = GPIO8
   GpioCtrlRegs.GPADIR.bit.GPIO8 = 1;   // GPIO8 = output

   GpioCtrlRegs.GPAPUD.bit.GPIO9 = 0;   // Enable pullup on GPIO9
   GpioDataRegs.GPASET.bit.GPIO9 = 1;   // Load output latch
   GpioCtrlRegs.GPAMUX1.bit.GPIO9 = 0;  // GPIO9 = GPIO9
   GpioCtrlRegs.GPADIR.bit.GPIO9 = 1;   // GPIO9 = output

   GpioCtrlRegs.GPAPUD.bit.GPIO10 = 0;  // Enable pullup on GPIO10
   GpioDataRegs.GPASET.bit.GPIO10 = 1;  // Load output latch
   GpioCtrlRegs.GPAMUX1.bit.GPIO10 = 0; // GPIO10 = GPIO10
   GpioCtrlRegs.GPADIR.bit.GPIO6 = 1;   // GPIO10 = output

   GpioCtrlRegs.GPAPUD.bit.GPIO11 = 0;  // Enable pullup on GPIO11
   GpioCtrlRegs.GPAMUX1.bit.GPIO11 = 0; // GPIO11 = GPIO11
   GpioCtrlRegs.GPADIR.bit.GPIO11 = 1;  // GPIO11 = output

   // Enable Trip Zone inputs on GPIO12 - GPIO15
   GpioCtrlRegs.GPAPUD.bit.GPIO12 = 0;   // Enable pullup on GPIO12
   GpioCtrlRegs.GPAPUD.bit.GPIO13 = 0;   // Enable pullup on GPIO13
   GpioCtrlRegs.GPAPUD.bit.GPIO14 = 0;   // Enable pullup on GPIO14
   GpioCtrlRegs.GPAPUD.bit.GPIO15 = 0;   // Enable pullup on GPIO15
   GpioCtrlRegs.GPAQSEL1.bit.GPIO12 = 3; // asynch input
   GpioCtrlRegs.GPAQSEL1.bit.GPIO13 = 3; // asynch input
   GpioCtrlRegs.GPAQSEL1.bit.GPIO14 = 3; // asynch input
   GpioCtrlRegs.GPAQSEL1.bit.GPIO15 = 3; // asynch input
   GpioCtrlRegs.GPAMUX1.bit.GPIO12 = 1;  // GPIO12 = TZ1
   GpioCtrlRegs.GPAMUX1.bit.GPIO13 = 1;  // GPIO13 = TZ2
   GpioCtrlRegs.GPAMUX1.bit.GPIO14 = 1;  // GPIO14 = TZ3
   GpioCtrlRegs.GPAMUX1.bit.GPIO15 = 1;  // GPIO15 = TZ4

   // Enable SPI-A on GPIO16 - GPIO19
   GpioCtrlRegs.GPAPUD.bit.GPIO16 = 0;   // Enable pullup on GPIO16
   GpioCtrlRegs.GPAPUD.bit.GPIO17 = 0;   // Enable pullup on GPIO17
   GpioCtrlRegs.GPAPUD.bit.GPIO18 = 0;   // Enable pullup on GPIO18
   GpioCtrlRegs.GPAPUD.bit.GPIO19 = 0;   // Enable pullup on GPIO19
   GpioCtrlRegs.GPAQSEL2.bit.GPIO16 = 3; // asynch input
   GpioCtrlRegs.GPAQSEL2.bit.GPIO17 = 3; // asynch input
   GpioCtrlRegs.GPAQSEL2.bit.GPIO18 = 3; // asynch input
   GpioCtrlRegs.GPAQSEL2.bit.GPIO19 = 3; // asynch input
   GpioCtrlRegs.GPAMUX2.bit.GPIO16 = 1;  // GPIO16 = SPICLKA
   GpioCtrlRegs.GPAMUX2.bit.GPIO17 = 1;  // GPIO17 = SPIS0MIA
   GpioCtrlRegs.GPAMUX2.bit.GPIO18 = 1;  // GPIO18 = SPICLKA
   GpioCtrlRegs.GPAMUX2.bit.GPIO19 = 1;  // GPIO19 = SPISTEA

   // Enable EQEP1 on GPIO20 - GPIO23
   GpioCtrlRegs.GPAPUD.bit.GPIO20 = 0;   // Enable pullup on GPIO20
   GpioCtrlRegs.GPAPUD.bit.GPIO21 = 0;   // Enable pullup on GPIO21