file_storage.c

ARM S3C2410 USB SLAVE LINUX驱动

/*
 * file_storage.c -- File-backed USB Storage Gadget, for USB development
 *
 * Copyright (C) 2003-2005 Alan Stern
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions, and the following disclaimer,
 *    without modification.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. The names of the above-listed copyright holders may not be used
 *    to endorse or promote products derived from this software without
 *    specific prior written permission.
 *
 * ALTERNATIVELY, this software may be distributed under the terms of the
 * GNU General Public License ("GPL") as published by the Free Software
 * Foundation, either version 2 of that License or (at your option) any
 * later version.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
 * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */


/*
 * The File-backed Storage Gadget acts as a USB Mass Storage device,
 * appearing to the host as a disk drive.  In addition to providing an
 * example of a genuinely useful gadget driver for a USB device, it also
 * illustrates a technique of double-buffering for increased throughput.
 * Last but not least, it gives an easy way to probe the behavior of the
 * Mass Storage drivers in a USB host.
 *
 * Backing storage is provided by a regular file or a block device, specified
 * by the "file" module parameter.  Access can be limited to read-only by
 * setting the optional "ro" module parameter.  The gadget will indicate that
 * it has removable media if the optional "removable" module parameter is set.
 *
 * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI),
 * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected
 * by the optional "transport" module parameter.  It also supports the
 * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03),
 * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by
 * the optional "protocol" module parameter.  In addition, the default
 * Vendor ID, Product ID, and release number can be overridden.
 *
 * There is support for multiple logical units (LUNs), each of which has
 * its own backing file.  The number of LUNs can be set using the optional
 * "luns" module parameter (anywhere from 1 to 8), and the corresponding
 * files are specified using comma-separated lists for "file" and "ro".
 * The default number of LUNs is taken from the number of "file" elements;
 * it is 1 if "file" is not given.  If "removable" is not set then a backing
 * file must be specified for each LUN.  If it is set, then an unspecified
 * or empty backing filename means the LUN's medium is not loaded.
 *
 * Requirements are modest; only a bulk-in and a bulk-out endpoint are
 * needed (an interrupt-out endpoint is also needed for CBI).  The memory
 * requirement amounts to two 16K buffers, size configurable by a parameter.
 * Support is included for both full-speed and high-speed operation.
 *
 * Module options:
 *
 *	file=filename[,filename...]
 *				Required if "removable" is not set, names of
 *					the files or block devices used for
 *					backing storage
 *	ro=b[,b...]		Default false, booleans for read-only access
 *	removable		Default false, boolean for removable media
 *	luns=N			Default N = number of filenames, number of
 *					LUNs to support
 *	stall			Default determined according to the type of
 *					USB device controller (usually true),
 *					boolean to permit the driver to halt
 *					bulk endpoints
 *	transport=XXX		Default BBB, transport name (CB, CBI, or BBB)
 *	protocol=YYY		Default SCSI, protocol name (RBC, 8020 or
 *					ATAPI, QIC, UFI, 8070, or SCSI;
 *					also 1 - 6)
 *	vendor=0xVVVV		Default 0x0525 (NetChip), USB Vendor ID
 *	product=0xPPPP		Default 0xa4a5 (FSG), USB Product ID
 *	release=0xRRRR		Override the USB release number (bcdDevice)
 *	buflen=N		Default N=16384, buffer size used (will be
 *					rounded down to a multiple of
 *					PAGE_CACHE_SIZE)
 *
 * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "ro",
 * "removable", "luns", and "stall" options are available; default values
 * are used for everything else.
 *
 * The pathnames of the backing files and the ro settings are available in
 * the attribute files "file" and "ro" in the lun<n> subdirectory of the
 * gadget's sysfs directory.  If the "removable" option is set, writing to
 * these files will simulate ejecting/loading the medium (writing an empty
 * line means eject) and adjusting a write-enable tab.  Changes to the ro
 * setting are not allowed when the medium is loaded.
 *
 * This gadget driver is heavily based on "Gadget Zero" by David Brownell.
 */


/*
 *				Driver Design
 *
 * The FSG driver is fairly straightforward.  There is a main kernel
 * thread that handles most of the work.  Interrupt routines field
 * callbacks from the controller driver: bulk- and interrupt-request
 * completion notifications, endpoint-0 events, and disconnect events.
 * Completion events are passed to the main thread by wakeup calls.  Many
 * ep0 requests are handled at interrupt time, but SetInterface,
 * SetConfiguration, and device reset requests are forwarded to the
 * thread in the form of "exceptions" using SIGUSR1 signals (since they
 * should interrupt any ongoing file I/O operations).
 *
 * The thread's main routine implements the standard command/data/status
 * parts of a SCSI interaction.  It and its subroutines are full of tests
 * for pending signals/exceptions -- all this polling is necessary since
 * the kernel has no setjmp/longjmp equivalents.  (Maybe this is an
 * indication that the driver really wants to be running in userspace.)
 * An important point is that so long as the thread is alive it keeps an
 * open reference to the backing file.  This will prevent unmounting
 * the backing file's underlying filesystem and could cause problems
 * during system shutdown, for example.  To prevent such problems, the
 * thread catches INT, TERM, and KILL signals and converts them into
 * an EXIT exception.
 *
 * In normal operation the main thread is started during the gadget's
 * fsg_bind() callback and stopped during fsg_unbind().  But it can also
 * exit when it receives a signal, and there's no point leaving the
 * gadget running when the thread is dead.  So just before the thread
 * exits, it deregisters the gadget driver.  This makes things a little
 * tricky: The driver is deregistered at two places, and the exiting
 * thread can indirectly call fsg_unbind() which in turn can tell the
 * thread to exit.  The first problem is resolved through the use of the
 * REGISTERED atomic bitflag; the driver will only be deregistered once.
 * The second problem is resolved by having fsg_unbind() check
 * fsg->state; it won't try to stop the thread if the state is already
 * FSG_STATE_TERMINATED.
 *
 * To provide maximum throughput, the driver uses a circular pipeline of
 * buffer heads (struct fsg_buffhd).  In principle the pipeline can be
 * arbitrarily long; in practice the benefits don't justify having more
 * than 2 stages (i.e., double buffering).  But it helps to think of the
 * pipeline as being a long one.  Each buffer head contains a bulk-in and
 * a bulk-out request pointer (since the buffer can be used for both
 * output and input -- directions always are given from the host's
 * point of view) as well as a pointer to the buffer and various state
 * variables.
 *
 * Use of the pipeline follows a simple protocol.  There is a variable
 * (fsg->next_buffhd_to_fill) that points to the next buffer head to use.
 * At any time that buffer head may still be in use from an earlier
 * request, so each buffer head has a state variable indicating whether
 * it is EMPTY, FULL, or BUSY.  Typical use involves waiting for the
 * buffer head to be EMPTY, filling the buffer either by file I/O or by
 * USB I/O (during which the buffer head is BUSY), and marking the buffer
 * head FULL when the I/O is complete.  Then the buffer will be emptied
 * (again possibly by USB I/O, during which it is marked BUSY) and
 * finally marked EMPTY again (possibly by a completion routine).
 *
 * A module parameter tells the driver to avoid stalling the bulk
 * endpoints wherever the transport specification allows.  This is
 * necessary for some UDCs like the SuperH, which cannot reliably clear a
 * halt on a bulk endpoint.  However, under certain circumstances the
 * Bulk-only specification requires a stall.  In such cases the driver
 * will halt the endpoint and set a flag indicating that it should clear
 * the halt in software during the next device reset.  Hopefully this
 * will permit everything to work correctly.  Furthermore, although the
 * specification allows the bulk-out endpoint to halt when the host sends
 * too much data, implementing this would cause an unavoidable race.
 * The driver will always use the "no-stall" approach for OUT transfers.
 *
 * One subtle point concerns sending status-stage responses for ep0
 * requests.  Some of these requests, such as device reset, can involve
 * interrupting an ongoing file I/O operation, which might take an
 * arbitrarily long time.  During that delay the host might give up on
 * the original ep0 request and issue a new one.  When that happens the
 * driver should not notify the host about completion of the original
 * request, as the host will no longer be waiting for it.  So the driver
 * assigns to each ep0 request a unique tag, and it keeps track of the
 * tag value of the request associated with a long-running exception
 * (device-reset, interface-change, or configuration-change).  When the
 * exception handler is finished, the status-stage response is submitted
 * only if the current ep0 request tag is equal to the exception request
 * tag.  Thus only the most recently received ep0 request will get a
 * status-stage response.
 *
 * Warning: This driver source file is too long.  It ought to be split up
 * into a header file plus about 3 separate .c files, to handle the details
 * of the Gadget, USB Mass Storage, and SCSI protocols.
 */


#undef DEBUG
#undef VERBOSE
#undef DUMP_MSGS

#include <linux/config.h>

#include <asm/system.h>
#include <asm/uaccess.h>

#include <linux/bitops.h>
#include <linux/blkdev.h>
#include <linux/compiler.h>
#include <linux/completion.h>
#include <linux/dcache.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/fcntl.h>
#include <linux/file.h>
#include <linux/fs.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/limits.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/pagemap.h>
#include <linux/rwsem.h>
#include <linux/sched.h>
#include <linux/signal.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/string.h>
#include <linux/suspend.h>
#include <linux/utsname.h>
#include <linux/wait.h>

#include <linux/usb_ch9.h>
#include <linux/usb_gadget.h>

#include "gadget_chips.h"


/*-------------------------------------------------------------------------*/

#define DRIVER_DESC		"File-backed Storage Gadget"
#define DRIVER_NAME		"g_file_storage"
#define DRIVER_VERSION		"20 October 2004"

static const char longname[] = DRIVER_DESC;
static const char shortname[] = DRIVER_NAME;

MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_AUTHOR("Alan Stern");
MODULE_LICENSE("Dual BSD/GPL");

/* Thanks to NetChip Technologies for donating this product ID.
 *
 * DO NOT REUSE THESE IDs with any other driver!!  Ever!!
 * Instead:  allocate your own, using normal USB-IF procedures. */
#define DRIVER_VENDOR_ID	0x0525	// NetChip
#define DRIVER_PRODUCT_ID	0xa4a5	// Linux-USB File-backed Storage Gadget


/*
 * This driver assumes self-powered hardware and has no way for users to
 * trigger remote wakeup.  It uses autoconfiguration to select endpoints
 * and endpoint addresses.
 */


/*-------------------------------------------------------------------------*/

#define xprintk(f,level,fmt,args...) \
	dev_printk(level , &(f)->gadget->dev , fmt , ## args)
#define yprintk(l,level,fmt,args...) \
	dev_printk(level , &(l)->dev , fmt , ## args)

//#define	DEBUG
#ifdef DEBUG
#define DBG(fsg,fmt,args...) \
	xprintk(fsg , KERN_DEBUG , fmt , ## args)
#define LDBG(lun,fmt,args...) \
	yprintk(lun , KERN_DEBUG , fmt , ## args)
#define MDBG(fmt,args...) \
	printk(KERN_DEBUG DRIVER_NAME ": " fmt , ## args)
#else
#define DBG(fsg,fmt,args...) \
	do { } while (0)
#define LDBG(lun,fmt,args...) \
	do { } while (0)
#define MDBG(fmt,args...) \
	do { } while (0)
#undef VERBOSE
#undef DUMP_MSGS
#endif /* DEBUG */

//#define VERBOSE
#ifdef VERBOSE
#define VDBG	DBG
#define VLDBG	LDBG
#else
#define VDBG(fsg,fmt,args...) \
	do { } while (0)
#define VLDBG(lun,fmt,args...) \
	do { } while (0)
#endif /* VERBOSE */

#define ERROR(fsg,fmt,args...) \
	xprintk(fsg , KERN_ERR , fmt , ## args)
#define LERROR(lun,fmt,args...) \
	yprintk(lun , KERN_ERR , fmt , ## args)

#define WARN(fsg,fmt,args...) \
	xprintk(fsg , KERN_WARNING , fmt , ## args)
#define LWARN(lun,fmt,args...) \
	yprintk(lun , KERN_WARNING , fmt , ## args)

#define INFO(fsg,fmt,args...) \
	xprintk(fsg , KERN_INFO , fmt , ## args)
#define LINFO(lun,fmt,args...) \
	yprintk(lun , KERN_INFO , fmt , ## args)

#define MINFO(fmt,args...) \
	printk(KERN_INFO DRIVER_NAME ": " fmt , ## args)


/*-------------------------------------------------------------------------*/

/* Encapsulate the module parameter settings */

#define MAX_LUNS	8

	/* Arggh!  There should be a module_param_array_named macro! */
static char		*file[MAX_LUNS] = {NULL, };
static int		ro[MAX_LUNS] = {0, };

static struct {
	int		num_filenames;
	int		num_ros;
	unsigned int	nluns;

	int		removable;
	int		can_stall;

	char		*transport_parm;
	char		*protocol_parm;
	unsigned short	vendor;
	unsigned short	product;
	unsigned short	release;
	unsigned int	buflen;

	int		transport_type;
	char		*transport_name;
	int		protocol_type;
	char		*protocol_name;

} mod_data = {					// Default values
	.transport_parm		= "BBB",
	.protocol_parm		= "SCSI",
	.removable		= 0,
	.can_stall		= 1,
	.vendor			= DRIVER_VENDOR_ID,
	.product		= DRIVER_PRODUCT_ID,
	.release		= 0xffff,	// Use controller chip type
	.buflen			= 16384,
	};


module_param_array(file, charp, &mod_data.num_filenames, S_IRUGO);
MODULE_PARM_DESC(file, "names of backing files or devices");

module_param_array(ro, bool, &mod_data.num_ros, S_IRUGO);
MODULE_PARM_DESC(ro, "true to force read-only");

module_param_named(luns, mod_data.nluns, uint, S_IRUGO);
MODULE_PARM_DESC(luns, "number of LUNs");

module_param_named(removable, mod_data.removable, bool, S_IRUGO);
MODULE_PARM_DESC(removable, "true to simulate removable media");

module_param_named(stall, mod_data.can_stall, bool, S_IRUGO);
MODULE_PARM_DESC(stall, "false to prevent bulk stalls");


/* In the non-TEST version, only the module parameters listed above
 * are available. */
#ifdef CONFIG_USB_FILE_STORAGE_TEST

module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO);
MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)");

module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO);
MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, "
		"8070, or SCSI)");

module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO);
MODULE_PARM_DESC(vendor, "USB Vendor ID");

module_param_named(product, mod_data.product, ushort, S_IRUGO);
MODULE_PARM_DESC(product, "USB Product ID");

module_param_named(release, mod_data.release, ushort, S_IRUGO);
MODULE_PARM_DESC(release, "USB release number");

module_param_named(buflen, mod_data.buflen, uint, S_IRUGO);
MODULE_PARM_DESC(buflen, "I/O buffer size");

#endif /* CONFIG_USB_FILE_STORAGE_TEST */


/*-------------------------------------------------------------------------*/

/* USB protocol value = the transport method */
#define USB_PR_CBI	0x00		// Control/Bulk/Interrupt
#define USB_PR_CB	0x01		// Control/Bulk w/o interrupt
#define USB_PR_BULK	0x50		// Bulk-only

/* USB subclass value = the protocol encapsulation */
#define USB_SC_RBC	0x01		// Reduced Block Commands (flash)
#define USB_SC_8020	0x02		// SFF-8020i, MMC-2, ATAPI (CD-ROM)
#define USB_SC_QIC	0x03		// QIC-157 (tape)
#define USB_SC_UFI	0x04		// UFI (floppy)
#define USB_SC_8070	0x05		// SFF-8070i (removable)
#define USB_SC_SCSI	0x06		// Transparent SCSI