syslib.c

标准arm vxworks bsp 模板

     */

#endif /* INCLUDE_CACHE_SUPPORT */


#if defined(INCLUDE_MMU)

    /* TODO -Install the appropriate MMU library and translation routines */

#endif /* defined(INCLUDE_MMU) */

    return;
    }

/*******************************************************************************
*
* sysHwInit - initialize the CPU board hardware
*
* This routine initializes various features of the board.
* It is the first board-specific C code executed, and runs with
* interrupts masked in the processor.
* This routine resets all devices to a quiescent state, typically
* by calling driver initialization routines.
*
* NOTE: Because this routine will be called from sysToMonitor, it must
* shutdown all potential DMA master devices.  If a device is doing DMA
* at reboot time, the DMA could interfere with the reboot. For devices
* on non-local busses, this is easy if the bus reset or sysFail line can
* be asserted.
*
* NOTE: This routine should not be called directly by the user application.
*
* RETURNS: N/A
*/

void sysHwInit (void)
    {
    /*
     * TODO - add initialization code for all devices and
     * for the interrupt controller.
     * Note: the interrupt controller should mask all interrupts here.
     * Interrupts are unmasked later on a per-device basis:
     *     device                     where unmasked
     *     ------                     --------------
     * abort switch, clock            sysHwInit2()
     * serial                         sysSerialHwInit2()
     * SCSI                           sysScsiInit()
     * LAN                            sysLanIntEnable()
     */

    /* install the IRQ/SVC interrupt stack splitting routine */

    _func_armIntStackSplit = sysIntStackSplit;

#if defined(INCLUDE_PCI)

    /* TODO - PCI hardware setup/reset */

#endif  /* INCLUDE_PCI */

#ifdef INCLUDE_SERIAL
    /* initialise the serial devices */
    sysSerialHwInit ();      /* initialise serial data structure */
#endif /* INCLUDE_SERIAL */
    }

/*******************************************************************************
*
* sysHwInit2 - additional system configuration and initialization
*
* This routine connects system interrupts and does any additional
* configuration necessary.  Note that this is called from
* sysClkConnect() in the timer driver.
*
* RETURNS: N/A
*
*/

void sysHwInit2 (void)
    {
    static BOOL initialised = FALSE;

    if (initialised)
    	return;

    /*
     * TODO - connect timer and abort vector interrupts and enable
     * those interrupts as needed.
     */

    /* initialise the interrupt library and interrupt driver */

    /* connect sys clock interrupt and auxiliary clock interrupt */

#ifdef INCLUDE_SERIAL
    /* connect serial interrupt */
    sysSerialHwInit2();
#endif /* INCLUDE_SERIAL */

#if defined (INCLUDE_PCI)
#if defined (INCLUDE_DEC21X40END) || defined (INCLUDE_FEI82557END)

    /* TODO - any secondary PCI setup */

    /* map all appropriate Ethernet PCI device memory and I/O addresses */

#endif  /* INCLUDE_DEC21X40END/FEI82557END */

#if defined (INCLUDE_USB)
    /* Low level init for usb */
    sysUsbPciInit();
#endif
#endif  /* INCLUDE_PCI */

    initialised = TRUE;

    }

/*******************************************************************************
*
* sysPhysMemTop - get the address of the top of physical memory
*
* This routine returns the address of the first missing byte of memory,
* which indicates the top of memory.
*
* Normally, the user specifies the amount of physical memory with the
* macro LOCAL_MEM_SIZE in config.h.  BSPs that support run-time
* memory sizing do so only if the macro LOCAL_MEM_AUTOSIZE is defined.
* If not defined, then LOCAL_MEM_SIZE is assumed to be, and must be, the
* true size of physical memory.
*
* NOTE: Do no adjust LOCAL_MEM_SIZE to reserve memory for application
* use.  See sysMemTop() for more information on reserving memory.
*
* RETURNS: The address of the top of physical memory.
*
* SEE ALSO: sysMemTop()
*/

char * sysPhysMemTop (void)
    {
    static char * physTop = NULL;

    if (physTop == NULL)
	{
#ifdef LOCAL_MEM_AUTOSIZE

        /* TODO - If auto-sizing is possible, this would be the spot.  */

#	error   "Dynamic memory sizing not supported"

#else
	/* Don't do autosizing, if size is given */

	physTop = (char *)(LOCAL_MEM_LOCAL_ADRS + LOCAL_MEM_SIZE);

#endif /* LOCAL_MEM_AUTOSIZE */
	}

    return physTop;
    }

/*******************************************************************************
*
* sysMemTop - get the address of the top of VxWorks memory
*
* This routine returns a pointer to the first byte of memory not
* controlled or used by VxWorks.
*
* The user can reserve memory space by defining the macro USER_RESERVED_MEM
* in config.h.  This routine returns the address of the reserved memory
* area.  The value of USER_RESERVED_MEM is in bytes.
*
* RETURNS: The address of the top of VxWorks memory.
*/

char * sysMemTop (void)
    {
    static char * memTop = NULL;

    if (memTop == NULL)
	{
	memTop = sysPhysMemTop () - USER_RESERVED_MEM;
	}

    return memTop;
    }

/*******************************************************************************
*
* sysToMonitor - transfer control to the ROM monitor
*
* This routine transfers control to the ROM monitor.  It is usually called
* only by reboot() -- which services ^X -- and bus errors at interrupt
* level.  However, in some circumstances, the user may wish to introduce a
* new <startType> to enable special boot ROM facilities.
*
* RETURNS: Does not return.
*/

STATUS sysToMonitor
    (
    int startType	/* passed to ROM to tell it how to boot */
    )
    {
    FUNCPTR	pRom;
    UINT32 *	p = (UINT32 *)ROM_TEXT_ADRS;

#ifdef INCLUDE_SERIAL
    sysSerialReset ();	/* put serial devices into quiet state */
#endif

    /*
     * Examine ROM - if it's a VxWorks boot ROM, jump to the warm boot entry
     * point; otherwise jump to the start of the ROM.
     * A VxWorks boot ROM begins
     *    MOV	R0,#BOOT_COLD
     *    B	...
     *    DCB	"Copyright"
     * We check the first and third words only. This could be tightened up
     * if required (see romInit.s).
     */

    if (p[0] == 0xE3A00002 && p[2] == 0x79706F43)
	pRom = (FUNCPTR)(ROM_TEXT_ADRS + 4);	/* warm boot address */
    else
	pRom = (FUNCPTR)ROM_TEXT_ADRS;		/* start of ROM */

#if defined(CPU_720T)  || defined(CPU_720T_T) || \
    defined(CPU_740T)  || defined(CPU_740T_T) || \
    defined(CPU_920T)  || defined(CPU_920T_T) || \
    defined(CPU_940T)  || defined(CPU_940T_T) || \
    defined(CPU_946ES) || defined(CPU_946ES_T)

    VM_ENABLE(FALSE);	/* disable the MMU, cache(s) and write-buffer */
#endif

#if defined(CPU_920T) || defined(CPU_920T_T)
    /*
     * On 920T, can have the I-cache enabled once the MMU has been
     * disabled, so, unlike the other processors, disabling the MMU does
     * not disable the I-cache.  This would not be a problem, as the
     * 920T boot ROM initialisation code disables and flushes both caches.
     * However, in case we are, in fact, using a 7TDMI boot ROM,
     * disable and flush the I-cache here, or else the boot process may
     * fail.
     */

    cacheDisable (INSTRUCTION_CACHE);
#endif /* defined(CPU_920T/920T_T) */

    (*pRom)(startType);	/* jump to boot ROM */

    return OK;		/* in case we ever continue from ROM monitor */
    }

/****************************************************************************
*
* sysProcNumGet - get the processor number
*
* This routine returns the processor number for the CPU board, which is
* set with sysProcNumSet().
*
* RETURNS: The processor number for the CPU board.
*
* SEE ALSO: sysProcNumSet()
*/

int sysProcNumGet (void)
    {
    return 0;
    }

/****************************************************************************
*
* sysProcNumSet - set the processor number
*
* Set the processor number for the CPU board.  Processor numbers should be
* unique on a single backplane.
*
* NOTE
* By convention, only processor 0 should dual-port its memory.
*
* RETURNS: N/A
*
* SEE ALSO: sysProcNumGet()
*/

void sysProcNumSet
    (
    int procNum		/* processor number */
    )
    {
    sysProcNum = procNum;
    }

/******************************************************************************
*
* sysLedsReadWrite - read/write the state of the LEDs on the board
*
* This routine can be used to read and write the state of the four LEDs
* on the board. The current state is ANDed and EORed with the supplied
* parameters. Bits 0..3 control LEDs 0..3. A 1 switches the LED on; a 0 off.
*
* RETURNS: previous state of LEDs.
*/

int sysLedsReadWrite
    (
    int and,
    int eor
    )
    {
    UINT32	 	current, previous;
    int			oldLevel;

    oldLevel = intLock();

    /* read current value from hardware and mask off undefined bits */

    current = *((volatile UINT32 *)LED_LIGHTS) & LED_LEDS_MASK;

    previous = current;
    current = (current & and) ^ eor;

    /* wait for display status to be idle */

    while (*((volatile UINT32 *)LED_ALPHA) & LED_STATUS)
	;

    /* set new value */

    *((volatile UINT32 *)LED_LIGHTS) = current;

    intUnlock (oldLevel);
    return previous;
    }

#ifdef INCLUDE_FLASH
/******************************************************************************
*
* sysFlashWriteEnable - enable write access to the Flash memory
*
* This routine is used by flashMem.c to enable write access to the
* Flash memory.
*
* RETURNS: N/A
*/

void sysFlashWriteEnable (void)
     {
     /* TODO - Enable Vpp and write access */
     }

/******************************************************************************
*
* sysFlashWriteDisable - disable write access to the Flash memory
*
* This routine is used by flashMem.c to disable write access to the
* Flash memory.
*
* RETURNS: N/A
*/

void sysFlashWriteDisable (void)
     {
     /* TODO - Disable Vpp and write access */
     }
#endif /* INCLUDE_FLASH */