system.c

ads下2410的测试程序

/*-----------------------------------------------------------------------------------------------
Project       :           test for 2410 hardware
Author        :           [e-mail]
Creation Date :           04-04-15
Revision      :           none 
-------------------------------------------------------------------------------------------------*/




#define  SYSTEM_G
#include "sysincludes.h"

#define  Time_Mask_Bit  (1<<10)
#define  Time_Enable_Bit ~(1<<10)
extern   void EnableInterrupt(void) ; 
extern   void DisableInterrupt( void ) ; 

static int delayLoopCount = FCLK/10000/10;

void Delay(int time)
{
      // time=0: adjust the Delay function by WatchDog timer.
      // time>0: the number of loop time
      // resolution of time is 100us.
    int i,adjust=0;
    if(time==0)
    {
        time   = 200;
        adjust = 1;
        delayLoopCount = 400;
            //PCLK/1M,Watch-dog disable,1/64,interrupt disable,reset disable
        rWTCON = ((PCLK/1000000-1)<<8)|(2<<3); 
        rWTDAT = 0xffff;                              //for first update
        rWTCNT = 0xffff;                              //resolution=64us @any PCLK 
        rWTCON = ((PCLK/1000000-1)<<8)|(2<<3)|(1<<5); //Watch-dog timer start
    }
    for(;time>0;time--)
        for(i=0;i<delayLoopCount;i++);
    if(adjust==1)
    {
        rWTCON = ((PCLK/1000000-1)<<8)|(2<<3);   //Watch-dog timer stop
        i = 0xffff - rWTCNT;                     //1count->64us, 200*400 cycle runtime = 64*i us
        delayLoopCount = 8000000/(i*64);         //200*400:64*i=1*x:100 -> x=80000*100/(64*i)   
    }
}


void DelayTime( uint times  ) 
{

   uint   iN ; 

   for( iN = 0 ; iN < times ; iN ++ ) ; 



}




void Port_Init(void)
{
    //CAUTION:Follow the configuration order for setting the ports. 
    // 1) setting value(GPnDAT) 
    // 2) setting control register  (GPnCON)
    // 3) configure pull-up resistor(GPnUP)  

    //32bit data bus configuration  
    //=== PORT A GROUP
    //Ports  : GPA22 GPA21  GPA20 GPA19 GPA18 GPA17 GPA16 GPA15 GPA14 GPA13 GPA12  
    //Signal : nFCE nRSTOUT nFRE   nFWE  ALE   CLE  nGCS5 nGCS4 nGCS3 nGCS2 nGCS1 
    //Binary :  1     1      1  , 1   1   1    1   ,  1     1     1     1
    //Ports  : GPA11   GPA10  GPA9   GPA8   GPA7   GPA6   GPA5   GPA4   GPA3   GPA2   GPA1  GPA0
    //Signal : ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR0 
    //Binary :  1       1      1      1   , 1       1      1      1   ,  1       1     1      1         
    rGPACON = 0x7fffff; 

    //===* PORT B GROUP
    //Ports  : GPB10    GPB9    GPB8    GPB7    GPB6     GPB5    GPB4   GPB3   GPB2     GPB1      GPB0
    //Signal : nXDREQ0 nXDACK0 nXDREQ1 nXDACK1 nSS_KBD nDIS_OFF L3CLOCK L3DATA L3MODE nIrDATXDEN Keyboard
    //Setting: INPUT  OUTPUT   INPUT  OUTPUT   INPUT   OUTPUT   OUTPUT OUTPUT OUTPUT   OUTPUT    OUTPUT 
    //Binary :   00  ,  01       00  ,   01      00   ,  01       01  ,   01     01   ,  01        01  
    rGPBCON = 0x044555;
    rGPBUP  = 0x7ff;     // The pull up function is disabled GPB[10:0]

    //=== PORT C GROUP
    //Ports  : GPC15 GPC14 GPC13 GPC12 GPC11 GPC10 GPC9 GPC8  GPC7   GPC6   GPC5 GPC4 GPC3  GPC2  GPC1 GPC0
    //Signal : VD7   VD6   VD5   VD4   VD3   VD2   VD1  VD0 LCDVF2 LCDVF1 LCDVF0 VM VFRAME VLINE VCLK LEND  
    //Binary :  10   10  , 10    10  , 10    10  , 10   10  , 10     10  ,  10   10 , 10     10 , 10   10
    rGPCCON = 0xaaaaaaaa;       
    rGPCUP  = 0xffff;     // The pull up function is disabled GPC[15:0] 

    //=== PORT D GROUP
    //Ports  : GPD15 GPD14 GPD13 GPD12 GPD11 GPD10 GPD9 GPD8 GPD7 GPD6 GPD5 GPD4 GPD3 GPD2 GPD1 GPD0
    //Signal : VD23  VD22  VD21  VD20  VD19  VD18  VD17 VD16 VD15 VD14 VD13 VD12 VD11 VD10 VD9  VD8
    //Binary : 10    10  , 10    10  , 10    10  , 10   10 , 10   10 , 10   10 , 10   10 ,10   10
    rGPDCON = 0xaaaaaaaa;       
    rGPDUP  = 0xffff;     // The pull up function is disabled GPD[15:0]

    //=== PORT E GROUP
    //Ports  : GPE15  GPE14 GPE13   GPE12   GPE11   GPE10   GPE9    GPE8     GPE7  GPE6  GPE5   GPE4  
    //Signal : IICSDA IICSCL SPICLK SPIMOSI SPIMISO SDDATA3 SDDATA2 SDDATA1 SDDATA0 SDCMD SDCLK I2SSDO 
    //Binary :  10     10  ,  10      10  ,  10      10   ,  10      10   ,   10    10  , 10     10  ,     
    //-------------------------------------------------------------------------------------------------------
    //Ports  :  GPE3   GPE2  GPE1    GPE0    
    //Signal : I2SSDI CDCLK I2SSCLK I2SLRCK     
    //Binary :  10     10  ,  10      10 
    rGPECON = 0xaaaaaaaa;       
    rGPEUP  = 0xffff;     // The pull up function is disabled GPE[15:0]

    //=== PORT F GROUP
    //Ports  : GPF7   GPF6   GPF5   GPF4      GPF3     GPF2  GPF1   GPF0
    //Signal : nLED_8 nLED_4 nLED_2 nLED_1 nIRQ_PCMCIA EINT2 KBDINT EINT0
    //Setting: Output Output Output Output    EINT3    EINT2 EINT1  EINT0
    //Binary :  01      01 ,  01     01  ,     10       10  , 10     10
    rGPFCON = 0x55aa;
    rGPFUP  = 0xff;     // The pull up function is disabled GPF[7:0]

    //=== PORT G GROUP
    //Ports  : GPG15 GPG14 GPG13 GPG12 GPG11    GPG10    GPG9     GPG8     GPG7      GPG6    
    //Signal : nYPON  YMON nXPON XMON  EINT19 DMAMODE1 DMAMODE0 DMASTART KBDSPICLK KBDSPIMOSI
    //Setting: nYPON  YMON nXPON XMON  EINT19  Output   Output   Output   SPICLK1    SPIMOSI1
    //Binary :   11    11 , 11    11  , 10      01    ,   01       01   ,    11         11
    //-----------------------------------------------------------------------------------------
    //Ports  :    GPG5       GPG4    GPG3    GPG2    GPG1    GPG0    
    //Signal : KBDSPIMISO LCD_PWREN EINT11 nSS_SPI IRQ_LAN IRQ_PCMCIA
    //Setting:  SPIMISO1  LCD_PWRDN EINT11   nSS0   EINT9    EINT8
    //Binary :     11         11   ,  10      11  ,  10        10
    rGPGCON = 0xff95ffba;
    rGPGUP  = 0xffff;    // The pull up function is disabled GPG[15:0]

/*    
    //GPG4 Output Port [9:8] 01      -> LCD_PWREN Enable
    rGPGCON = (rGPGCON & 0xfffffcff) | (1<<8);
    rGPGDAT = (rGPGDAT & 0xffef) | (1<<4);
*/
    //=== PORT H GROUP
    //Ports  :  GPH10    GPH9  GPH8 GPH7  GPH6  GPH5 GPH4 GPH3 GPH2 GPH1  GPH0 
    //Signal : CLKOUT1 CLKOUT0 UCLK nCTS1 nRTS1 RXD1 TXD1 RXD0 TXD0 nRTS0 nCTS0
    //Binary :   10   ,  10     10 , 11    11  , 10   10 , 10   10 , 10    10
    rGPHCON = 0x2afaaa;
    rGPHUP  = 0x7ff;    // The pull up function is disabled GPH[10:0]
    
    //External interrupt will be falling edge triggered. 
    rEXTINT0 = 0x22222222;    // EINT[7:0]
    rEXTINT1 = 0x22222222;    // EINT[15:8]
    rEXTINT2 = 0x22222222;    // EINT[23:16]
}

void ChangeClockDivider(int hdivn,int pdivn)
{
     // hdivn,pdivn FCLK:HCLK:PCLK
     //     0,0         1:1:1 
     //     0,1         1:1:2 
     //     1,0         1:2:2
     //     1,1         1:2:4
    rCLKDIVN = (hdivn<<1) | pdivn;    
    
   
}


void ChangeMPllValue(int mdiv,int pdiv,int sdiv)
{
    rMPLLCON = (mdiv<<12) | (pdiv<<4) | sdiv;
}



void SysInit( void ) 
{
    
    DelayTime( 5000 ) ; 
     
    ChangeClockDivider( 1,1);  
    ChangeMPllValue(0xa1,0x3,0x1);    // FCLK=202.8MHz  
    

    Port_Init() ; 

    UartInit( 0, 115200 ) ; 


}






void InterruptInit( void ) 
{
  
   
   rINTMSK  =  0x07ffffff;
   
   rINTSUBMSK  = 0x7ff ; 
   
   rINTMOD  = 0x0 ;
   
 
  
 

}
 
void  __irq OS_TICK_ISR (void)
{
   
   
   
     rINTPND = BIT_TIMER0 ;   // clear pending bit 
     rSRCPND = BIT_TIMER0 ; 
    
     
     OSIntEnter();

     OSTimeTick();                                   /* 系统节拍服务程序.    */

     OSIntExit();

   
   
   
}













void Timer0Init( void )  
{

   pISR_TIMER0 = (uint )OS_TICK_ISR ;
       
     
   
   rINTMSK =  ~BIT_TIMER0 ;
   
     
   rTCFG0 = 126   ;     //Dead zone=0,Prescaler1=15(0x0f),Prescaler0=15(0x0f)
   
   rTCFG1  = 0x000002;         //All interrupt,Mux4=1/2,Mux3=1/4,Mux2=1/8,Mux1=1/16,Mux0=1/16
   
   rTCNTB0 = 1000;           //(1/(50MHz/16/16)) * 0xffff (65535) = 0.334s ( 2.994Hz)
   
   rTCON   = 0x6aaa02; //Auto reload (T0=One-shot), Inverter off, Manual update, Dead zone disable, Stop
  
   rTCON   = 0x09;         //Auto reload(T0=One-shot),Inverter off,No operation,Dead zone disable,Start

   rSRCPND = 0xFFFFFFFF ;  
    
   EnableInterrupt() ; 
  
   
 
}