wx_n_sharp_lq106k1la.txt

来自「显示屏驱动源代码」· 文本 代码 · 共 188 行

/*===========================================================================*/
/*                    Register Setting for TW8804                     */
/*===========================================================================*/
//	Input	: NTSC
//	Panel	: WXGA-LG-
//-----------------------------------------------------------------------------
//	Below listed registers should not be set.
//	0x02, 0x06, 
//
//

TW88I2CAddress, 0xff,
0xff, 0x01,
0xc1, 0x25, //// ADC PLL=27Mhz 

0xff, 0x00,
//------------ Decoder (28) ---------------------------------------------------

0x1c, 0x08,				// Standard, shadow 		** N/P

0x02, 0x40,
0x06, 0x03,
0x04, 0x00,				// Luminance Gamma
0x07, 0x02,				// Cropping H				** N/P, panel
0x08, 0x16,				// V delay L				** N/P, panel
0x09, 0xf5,				// V active L				** N/P, panel?
0x0a, 0x20,				// H delay L				** N/P, panel
0x0b, 0xd0,				// H active L				** N/P, panel?
0x0c, 0xcd,				// Control Reg 1

0x10, 0x00,
0x11, 0x61,
0x12, 0x52,				// Sharpness Ctrl 1
0x13, 0x9e,				// Chroma(U) gain
0x14, 0x9e,				// chroma(V) gain
0x15, 0x00,				// Hue
0x16, 0xc3,				// Sharpness Ctrl 2
0x17, 0x33,				// V peaking Ctrl 1			
0x18, 0x44,				// Coring Ctrl				
0x1c, 0x1f,
0x1d, 0x7f,
0x1e, 0x08,

0x20, 0x50,
0x21, 0x44,				// AGC gain
0x22, 0xf0,
0x23, 0xd8,				// White Peak Threshold
0x24, 0xbc,
//0x24, 0x3c,
0x25, 0xb8,
0x26, 0x44,
0x27, 0x2A, // Default Changed from 0x32
0x28, 0x00,
0x29, 0x15,
0x2a, 0x78,
0x2b, 0x44,
0x2c, 0x30,
0x2d, 0x14,
0x2e, 0xa5,
0x2f, 0xe0,

0x33, 0x05,
0x34, 0x1a,
0x35, 0x02,
0x36, 0x00,
0x37, 0x00,				// QCLAMP
0x38, 0x8e,
0x39, 0x00,
0x3a, 0x00,
0x3b, 0x00,
0x3c, 0x00,
0x3d, 0x00,
0x3e, 0x00,
0x3f, 0x00,

//---------- Input/Output -----------------------------------------------------

0x40, 0x00,				// VPOL=ACtive LOW;
0x41, 0x20,				// Output
0x42, 0x04,
0x43, 0x22,				// Input routing
0x44, 0x08,				// Input control
0x45, 0x54,
0x46, 0x20,
0x47, 0x00,
0x48, 0xcf,
0x49, 0x20,
0x4a, 0x13,
0x4b, 0x13,
0x4c, 0x00,
0x4d, 0x30,
0x4e, 0x10,
0x4f, 0x08,

//------------ Zoom -----------------------------------------------------------

0x63, 0x00,				// H/V scale up/dn H		** N/P panel
0x60, 0x8a,				// H-scale up L				** N/P panel
0x61, 0x80,				// H-scale dn L				** N/P panel
0x62, 0x50,				// V-scale up L				** N/P panel
0x64, 0xff,				// H-scale up offset, remove error
0x65, 0x80,				// V-scale up offset
0x66, 0x00,				// H non-display area
0x67, 0x00,
0x68, 0x00,
//--------- Image Adjust ------------------------------------------------------

0x70, 0x60,				// YCbCr/ Hue
0x71, 0x80,				// Y  contrast
0x72, 0x80,				// Cb contrast
0x73, 0x80,				// Cr contrast
0x74, 0x80,				// Y  brightness
0x75, 0x80,				// Cb brightness
0x76, 0x80,				// Cr brightness
0x77, 0x30,				// Sharpness=0
0x78, 0x3b,				// Sharpness freq. Filter
0x79, 0x00,				// Edge Enhancement=enable
0x7a, 0x30,
0x7c, 0x1c,
0x7d, 0x08,
0x7e, 0xf6,
0x7f, 0x08,

//---------- BW/Blue Stretch --------------------------------------------------

0x80, 0x10,
0x81, 0x0d,
0x82, 0x03,
0x83, 0x00,
0x84, 0x67,				// BW Stretch Black Tilt
0x85, 0x94,				// BW Stretch White Tilt
0x86, 0x00,				// BW Stretch Black Gain, for Disable=00 
0x87, 0xff,				// BW Stretch White Gain, for Disable=FF
0x88, 0xca,
0x89, 0x02,
0x8a, 0x08,				// Blue Stretch, for Disable=00
0x8b, 0x04,

//--------- Display control ---------------------------------------------------

0xb0, 0x48,	// FPCLK_POL=1 (Red Dot Noise)// Output Signal Config.
0xb1, 0x00,				// clock delay, en coast	
0xbb, 0x33,				// PVR-H, PVP-H							
0xb7, 0x22,				// PVP-L						
0xb8, 0x06,				// V Sync						
0xb9, 0x4c,				// V Back Porch							
0xba, 0x00,				// PVR-L							
0xb6, 0x52,				// PHR-H, PHP-H				
0xb2, 0x0b,				// PHP-L				
0xb3, 0x68,				// H sync				
0xb4, 0xe1,				// H back porch				
0xb5, 0x00,				// PHR-L				
0xbd, 0x08,
0xbc, 0x21,				// Dithering
0xbe, 0x02,				// Auto Calc., FORCE SHORT
0xbf, 0x00,

//--------- Misc. Input -------------------------------------------------------

0xc0, 0x00,				// Initial Counter			
0xc1, 0x00,				//					
0xc2, 0x00,				//					
0xc3, 0x00,
0xc4, 0x40,

//--------- PLL ---------------------------------------------------------------

0xd4, 0x00,
0xd5, 0x3f,
0xd6, 0x00,
0xd7, 0x00,
0xd8, 0x00,
0xf9, 0x03,
0xfa, 0x09,				// 72Mhz
0xfb, 0x7b,				//						
0xfc, 0x00,				// 							** N/P panel
0xfd, 0x0c,				// VCO=10, POST=0
0xfe, 0x00,				//							** N/P panel
0xf8, 0x00,

0xff, 0x10,				// disable I2C auto increase mode
//-----------------------------------------------------------------------------

0xff, 0xff