sym_defs.h

内核linux2.4.20,可跟rtlinux3.2打补丁 组成实时linux系统,编译内核

        #define   LOA     0x08  /* sta: arbitration lost            */
        #define   WOA     0x04  /* sta: arbitration won             */
        #define   IRST    0x02  /* sta: scsi reset signal           */
        #define   SDP     0x01  /* sta: scsi parity signal          */

/*0e*/  u8	nc_sstat1;
	#define   FF3210  0xf0	/* sta: bytes in the scsi fifo      */

/*0f*/  u8	nc_sstat2;
        #define   ILF1    0x80  /* sta: data in SIDL register msb[W]*/
        #define   ORF1    0x40  /* sta: data in SODR register msb[W]*/
        #define   OLF1    0x20  /* sta: data in SODL register msb[W]*/
        #define   DM      0x04  /* sta: DIFFSENS mismatch (895/6 only) */
        #define   LDSC    0x02  /* sta: disconnect & reconnect      */

/*10*/  u8	nc_dsa;		/* --> Base page                    */
/*11*/  u8	nc_dsa1;
/*12*/  u8	nc_dsa2;
/*13*/  u8	nc_dsa3;

/*14*/  u8	nc_istat;	/* --> Main Command and status      */
        #define   CABRT   0x80  /* cmd: abort current operation     */
        #define   SRST    0x40  /* mod: reset chip                  */
        #define   SIGP    0x20  /* r/w: message from host to script */
        #define   SEM     0x10  /* r/w: message between host + script  */
        #define   CON     0x08  /* sta: connected to scsi           */
        #define   INTF    0x04  /* sta: int on the fly (reset by wr)*/
        #define   SIP     0x02  /* sta: scsi-interrupt              */
        #define   DIP     0x01  /* sta: host/script interrupt       */

/*15*/  u8	nc_istat1;	/* 896 only */
        #define   FLSH    0x04  /* sta: chip is flushing            */
        #define   SCRUN   0x02  /* sta: scripts are running         */
        #define   SIRQD   0x01  /* r/w: disable INT pin             */

/*16*/  u8	nc_mbox0;	/* 896 only */
/*17*/  u8	nc_mbox1;	/* 896 only */

/*18*/	u8	nc_ctest0;
/*19*/  u8	nc_ctest1;

/*1a*/  u8	nc_ctest2;
	#define   CSIGP   0x40
				/* bits 0-2,7 rsvd for C1010        */

/*1b*/  u8	nc_ctest3;
	#define   FLF     0x08  /* cmd: flush dma fifo              */
	#define   CLF	  0x04	/* cmd: clear dma fifo		    */
	#define   FM      0x02  /* mod: fetch pin mode              */
	#define   WRIE    0x01  /* mod: write and invalidate enable */
				/* bits 4-7 rsvd for C1010          */

/*1c*/  u32	nc_temp;	/* ### Temporary stack              */

/*20*/	u8	nc_dfifo;
/*21*/  u8	nc_ctest4;
	#define   BDIS    0x80  /* mod: burst disable               */
	#define   MPEE    0x08  /* mod: master parity error enable  */

/*22*/  u8	nc_ctest5;
	#define   DFS     0x20  /* mod: dma fifo size               */
				/* bits 0-1, 3-7 rsvd for C1010     */

/*23*/  u8	nc_ctest6;

/*24*/  u32	nc_dbc;		/* ### Byte count and command       */
/*28*/  u32	nc_dnad;	/* ### Next command register        */
/*2c*/  u32	nc_dsp;		/* --> Script Pointer               */
/*30*/  u32	nc_dsps;	/* --> Script pointer save/opcode#2 */

/*34*/  u8	nc_scratcha;	/* Temporary register a            */
/*35*/  u8	nc_scratcha1;
/*36*/  u8	nc_scratcha2;
/*37*/  u8	nc_scratcha3;

/*38*/  u8	nc_dmode;
	#define   BL_2    0x80  /* mod: burst length shift value +2 */
	#define   BL_1    0x40  /* mod: burst length shift value +1 */
	#define   ERL     0x08  /* mod: enable read line            */
	#define   ERMP    0x04  /* mod: enable read multiple        */
	#define   BOF     0x02  /* mod: burst op code fetch         */

/*39*/  u8	nc_dien;
/*3a*/  u8	nc_sbr;

/*3b*/  u8	nc_dcntl;	/* --> Script execution control     */
	#define   CLSE    0x80  /* mod: cache line size enable      */
	#define   PFF     0x40  /* cmd: pre-fetch flush             */
	#define   PFEN    0x20  /* mod: pre-fetch enable            */
	#define   SSM     0x10  /* mod: single step mode            */
	#define   IRQM    0x08  /* mod: irq mode (1 = totem pole !) */
	#define   STD     0x04  /* cmd: start dma mode              */
	#define   IRQD    0x02  /* mod: irq disable                 */
 	#define	  NOCOM   0x01	/* cmd: protect sfbr while reselect */
				/* bits 0-1 rsvd for C1010          */

/*3c*/  u32	nc_adder;

/*40*/  u16	nc_sien;	/* -->: interrupt enable            */
/*42*/  u16	nc_sist;	/* <--: interrupt status            */
        #define   SBMC    0x1000/* sta: SCSI Bus Mode Change (895/6 only) */
        #define   STO     0x0400/* sta: timeout (select)            */
        #define   GEN     0x0200/* sta: timeout (general)           */
        #define   HTH     0x0100/* sta: timeout (handshake)         */
        #define   MA      0x80  /* sta: phase mismatch              */
        #define   CMP     0x40  /* sta: arbitration complete        */
        #define   SEL     0x20  /* sta: selected by another device  */
        #define   RSL     0x10  /* sta: reselected by another device*/
        #define   SGE     0x08  /* sta: gross error (over/underflow)*/
        #define   UDC     0x04  /* sta: unexpected disconnect       */
        #define   RST     0x02  /* sta: scsi bus reset detected     */
        #define   PAR     0x01  /* sta: scsi parity error           */

/*44*/  u8	nc_slpar;
/*45*/  u8	nc_swide;
/*46*/  u8	nc_macntl;
/*47*/  u8	nc_gpcntl;
/*48*/  u8	nc_stime0;	/* cmd: timeout for select&handshake*/
/*49*/  u8	nc_stime1;	/* cmd: timeout user defined        */
/*4a*/  u16	nc_respid;	/* sta: Reselect-IDs                */

/*4c*/  u8	nc_stest0;

/*4d*/  u8	nc_stest1;
	#define   SCLK    0x80	/* Use the PCI clock as SCSI clock	*/
	#define   DBLEN   0x08	/* clock doubler running		*/
	#define   DBLSEL  0x04	/* clock doubler selected		*/
  

/*4e*/  u8	nc_stest2;
	#define   ROF     0x40	/* reset scsi offset (after gross error!) */
	#define   EXT     0x02  /* extended filtering                     */

/*4f*/  u8	nc_stest3;
	#define   TE     0x80	/* c: tolerAnt enable */
	#define   HSC    0x20	/* c: Halt SCSI Clock */
	#define   CSF    0x02	/* c: clear scsi fifo */

/*50*/  u16	nc_sidl;	/* Lowlevel: latched from scsi data */
/*52*/  u8	nc_stest4;
	#define   SMODE  0xc0	/* SCSI bus mode      (895/6 only) */
	#define    SMODE_HVD 0x40	/* High Voltage Differential       */
	#define    SMODE_SE  0x80	/* Single Ended                    */
	#define    SMODE_LVD 0xc0	/* Low Voltage Differential        */
	#define   LCKFRQ 0x20	/* Frequency Lock (895/6 only)     */
				/* bits 0-5 rsvd for C1010         */

/*53*/  u8	nc_53_;
/*54*/  u16	nc_sodl;	/* Lowlevel: data out to scsi data  */
/*56*/	u8	nc_ccntl0;	/* Chip Control 0 (896)             */
	#define   ENPMJ  0x80	/* Enable Phase Mismatch Jump       */
	#define   PMJCTL 0x40	/* Phase Mismatch Jump Control      */
	#define   ENNDJ  0x20	/* Enable Non Data PM Jump          */
	#define   DISFC  0x10	/* Disable Auto FIFO Clear          */
	#define   DILS   0x02	/* Disable Internal Load/Store      */
	#define   DPR    0x01	/* Disable Pipe Req                 */

/*57*/	u8	nc_ccntl1;	/* Chip Control 1 (896)             */
	#define   ZMOD   0x80	/* High Impedance Mode              */
	#define   DDAC   0x08	/* Disable Dual Address Cycle       */
	#define   XTIMOD 0x04	/* 64-bit Table Ind. Indexing Mode  */
	#define   EXTIBMV 0x02	/* Enable 64-bit Table Ind. BMOV    */
	#define   EXDBMV 0x01	/* Enable 64-bit Direct BMOV        */

/*58*/  u16	nc_sbdl;	/* Lowlevel: data from scsi data    */
/*5a*/  u16	nc_5a_;

/*5c*/  u8	nc_scr0;	/* Working register B               */
/*5d*/  u8	nc_scr1;
/*5e*/  u8	nc_scr2;
/*5f*/  u8	nc_scr3;

/*60*/  u8	nc_scrx[64];	/* Working register C-R             */
/*a0*/	u32	nc_mmrs;	/* Memory Move Read Selector        */
/*a4*/	u32	nc_mmws;	/* Memory Move Write Selector       */
/*a8*/	u32	nc_sfs;		/* Script Fetch Selector            */
/*ac*/	u32	nc_drs;		/* DSA Relative Selector            */
/*b0*/	u32	nc_sbms;	/* Static Block Move Selector       */
/*b4*/	u32	nc_dbms;	/* Dynamic Block Move Selector      */
/*b8*/	u32	nc_dnad64;	/* DMA Next Address 64              */
/*bc*/	u16	nc_scntl4;	/* C1010 only                       */
	#define   U3EN    0x80	/* Enable Ultra 3                   */
	#define   AIPCKEN 0x40  /* AIP checking enable              */
				/* Also enable AIP generation on C10-33*/
	#define   XCLKH_DT 0x08 /* Extra clock of data hold on DT edge */
	#define   XCLKH_ST 0x04 /* Extra clock of data hold on ST edge */
	#define   XCLKS_DT 0x02 /* Extra clock of data set  on DT edge */
	#define   XCLKS_ST 0x01 /* Extra clock of data set  on ST edge */
/*be*/	u8	nc_aipcntl0;	/* AIP Control 0 C1010 only         */
/*bf*/	u8	nc_aipcntl1;	/* AIP Control 1 C1010 only         */
	#define DISAIP  0x08	/* Disable AIP generation C10-66 only  */
/*c0*/	u32	nc_pmjad1;	/* Phase Mismatch Jump Address 1    */
/*c4*/	u32	nc_pmjad2;	/* Phase Mismatch Jump Address 2    */
/*c8*/	u8	nc_rbc;		/* Remaining Byte Count             */
/*c9*/	u8	nc_rbc1;
/*ca*/	u8	nc_rbc2;
/*cb*/	u8	nc_rbc3;

/*cc*/	u8	nc_ua;		/* Updated Address                  */
/*cd*/	u8	nc_ua1;
/*ce*/	u8	nc_ua2;
/*cf*/	u8	nc_ua3;
/*d0*/	u32	nc_esa;		/* Entry Storage Address            */
/*d4*/	u8	nc_ia;		/* Instruction Address              */
/*d5*/	u8	nc_ia1;
/*d6*/	u8	nc_ia2;
/*d7*/	u8	nc_ia3;
/*d8*/	u32	nc_sbc;		/* SCSI Byte Count (3 bytes only)   */
/*dc*/	u32	nc_csbc;	/* Cumulative SCSI Byte Count       */
                                /* Following for C1010 only         */
/*e0*/	u16    nc_crcpad;	/* CRC Value                        */
/*e2*/	u8     nc_crccntl0;	/* CRC control register             */
	#define   SNDCRC  0x10	/* Send CRC Request                 */
/*e3*/	u8     nc_crccntl1;	/* CRC control register             */
/*e4*/	u32    nc_crcdata;	/* CRC data register                */
/*e8*/	u32    nc_e8_;
/*ec*/	u32    nc_ec_;
/*f0*/	u16    nc_dfbc;		/* DMA FIFO byte count              */ 
};

/*-----------------------------------------------------------
 *
 *	Utility macros for the script.
 *
 *-----------------------------------------------------------
 */

#define REGJ(p,r) (offsetof(struct sym_reg, p ## r))
#define REG(r) REGJ (nc_, r)

/*-----------------------------------------------------------
 *
 *	SCSI phases
 *
 *-----------------------------------------------------------
 */

#define	SCR_DATA_OUT	0x00000000
#define	SCR_DATA_IN	0x01000000
#define	SCR_COMMAND	0x02000000
#define	SCR_STATUS	0x03000000
#define	SCR_DT_DATA_OUT	0x04000000
#define	SCR_DT_DATA_IN	0x05000000
#define SCR_MSG_OUT	0x06000000
#define SCR_MSG_IN      0x07000000
/* DT phases are illegal for non Ultra3 mode */
#define SCR_ILG_OUT	0x04000000
#define SCR_ILG_IN	0x05000000

/*-----------------------------------------------------------
 *
 *	Data transfer via SCSI.
 *
 *-----------------------------------------------------------
 *
 *	MOVE_ABS (LEN)
 *	<<start address>>
 *
 *	MOVE_IND (LEN)
 *	<<dnad_offset>>
 *
 *	MOVE_TBL
 *	<<dnad_offset>>
 *
 *-----------------------------------------------------------
 */

#define OPC_MOVE          0x08000000

#define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l))
/* #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) */
#define SCR_MOVE_TBL     (0x10000000 | OPC_MOVE)

#define SCR_CHMOV_ABS(l) ((0x00000000) | (l))
/* #define SCR_CHMOV_IND(l) ((0x20000000) | (l)) */
#define SCR_CHMOV_TBL     (0x10000000)

#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
/* We steal the `indirect addressing' flag for target mode MOVE in scripts */

#define OPC_TCHMOVE        0x08000000

#define SCR_TCHMOVE_ABS(l) ((0x20000000 | OPC_TCHMOVE) | (l))
#define SCR_TCHMOVE_TBL     (0x30000000 | OPC_TCHMOVE)

#define SCR_TMOV_ABS(l)    ((0x20000000) | (l))
#define SCR_TMOV_TBL        (0x30000000)
#endif

struct sym_tblmove {
        u32  size;
        u32  addr;
};

/*-----------------------------------------------------------
 *
 *	Selection
 *
 *-----------------------------------------------------------
 *
 *	SEL_ABS | SCR_ID (0..15)    [ | REL_JMP]
 *	<<alternate_address>>
 *
 *	SEL_TBL | << dnad_offset>>  [ | REL_JMP]
 *	<<alternate_address>>
 *
 *-----------------------------------------------------------
 */

#define	SCR_SEL_ABS	0x40000000
#define	SCR_SEL_ABS_ATN	0x41000000
#define	SCR_SEL_TBL	0x42000000
#define	SCR_SEL_TBL_ATN	0x43000000

#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
#define	SCR_RESEL_ABS     0x40000000
#define	SCR_RESEL_ABS_ATN 0x41000000
#define	SCR_RESEL_TBL     0x42000000
#define	SCR_RESEL_TBL_ATN 0x43000000
#endif