📄 cs8900a.h
字号:
#include "DSP28_Device.h"
#ifndef __CS8900_H
#define __CS8900_H
#define MY_TCP_PORT 1024
#define MY_UDP_PORT 1025
#define ETH_HEADER_START 0
#define IP_HEADER_START 7
#define ARP_HEADER_START 7
#define TCP_HEADER_START 17
#define UDP_HEADER_START 17
#define ICMP_HEADER_START 17
#define USER_DATA_START 27
#define ETH_HEADER_SIZE 7
#define IP_HEADER_SIZE 10
#define TCP_HEADER_SIZE 10
#define UDP_HEADER_SIZE 4
#define ARP_FRAME_SIZE 14
#define ICMP_HEADER_SIZE 2
#define DUMMY_HEADER_SIZE 6
#define MY_MAX_SEG_SIZE 1460
#define Frame_ARP 0x0806
#define Frame_IP 0x0800
#define Ip_Edition 0x4500 //Ip 版本和IP首部长度
#define DEFUALT_TTL 128
#define ICMP_ECHO 8
#define ICMP_ECHO_REPLY 0
//ARP
#define HARDW_ETH 1
#define IP_HLEN_PLEN 0x0604
#define OP_ARP_REQUEST 1
#define OP_ARP_ANSWER 2
#define PROTOCOL_ICMP 1
#define PROTOCOL_TCP 6
#define PROTOCOL_UDP 17
/////TCP define
#define TCP_MAX_RE_TXDNUM 8
#define TCP_CODE_FIN 0x0001
#define TCP_CODE_SYN 0x0002
#define TCP_CODE_RST 0x0004
#define TCP_CODE_PSH 0x0008
#define TCP_CODE_ACK 0x0010
#define TCP_CODE_URG 0x0020
#define TCP_STATE_LISTEN 0
#define TCP_STATE_SYN_RCVD 1
#define TCP_STATE_SYN_SENT 2
#define TCP_STATE_ESTABLISHED 3
#define TCP_STATE_FIN_WAIT1 4
#define TCP_STATE_FIN_WAIT2 5
#define TCP_STATE_CLOSING 6
#define TCP_STATE_CLOSE_WAIT 7
#define TCP_STATE_LAST_ACK 8
#define TCP_STATE_CLOSED 9
#define TCP_STATE_TIME_WAIT 10
// definitions for Crystal CS8900 ethernet-controller
// based on linux-header by Russel Nelson
#define DataPort (*((volatile unsigned int *)0x4B00))
#define TransmitCommand (*((volatile unsigned int *)0x4B04))
#define TransmitLenth (*((volatile unsigned int *)0x4B06))
#define InterruptSQ (*((volatile unsigned int *)0x4B08))
#define RegisterAddress (*((volatile unsigned int *)0x4B0A))
#define RegisterData (*((volatile unsigned int *)0x4B0C))
#define PP_ChipID 0x0000 // offset 0h -> Corp-ID
// offset 2h -> Model/Product Number
// offset 3h -> Chip Revision Number
#define PP_ISAIOB 0x0020 // IO base address
#define PP_CS8900_ISAINT 0x0022 // ISA interrupt select
#define PP_CS8900_ISADMA 0x0024 // ISA Rec DMA channel
#define PP_ISASOF 0x0026 // ISA DMA offset
#define PP_DmaFrameCnt 0x0028 // ISA DMA Frame count
#define PP_DmaByteCnt 0x002A // ISA DMA Byte count
#define PP_CS8900_ISAMemB 0x002C // Memory base
#define PP_ISABootBase 0x0030 // Boot Prom base
#define PP_ISABootMask 0x0034 // Boot Prom Mask
// Configuration and control registers
#define PP_RxCFG 0x0102 // Rx Bus config
#define PP_RxCTL 0x0104 // Receive Control Register
#define PP_TxCFG 0x0106 // Transmit Config Register
#define PP_TxCMD 0x0108 // Transmit Command Register
#define PP_BufCFG 0x010A // Bus configuration Register
#define PP_LineCTL 0x0112 // Line Config Register
#define PP_SelfCTL 0x0114 // Self Control Register
#define PP_BusCTL 0x0116 // ISA bus control Register
#define PP_TestCTL 0x0118 // Test Register
// Status and Event Registers
#define PP_ISQ 0x0120 // Interrupt Status
#define PP_RxEvent 0x0124 // Rx Event Register
#define PP_TxEvent 0x0128 // Tx Event Register
#define PP_BufEvent 0x012C // Bus Event Register
#define PP_RxMiss 0x0130 // Receive Miss Count
#define PP_TxCol 0x0132 // Transmit Collision Count
#define PP_LineST 0x0134 // Line State Register
#define PP_SelfST 0x0136 // Self State register
#define PP_BusST 0x0138 // Bus Status
#define PP_TDR 0x013C // Time Domain Reflectometry
// Initiate Transmit Registers
#define PP_TxCommand 0x0144 // Tx Command
#define PP_TxLength 0x0146 // Tx Length
// Adress Filter Registers
#define PP_LAF 0x0150 // Hash Table
#define PP_IA 0x0158 // Physical Address Register
// Frame Location in memory operation
#define PP_RxStatus 0x0400 // Receive start of frame
#define PP_RxLength 0x0402 // Receive Length of frame
#define PP_RxFrame 0x0404 // Receive frame pointer
#define PP_TxFrame 0x0A00 // Transmit frame pointer
// Primary I/O Base Address. If no I/O base is supplied by the user, then this
// can be used as the default I/O base to access the PacketPage Area.
#define DEFAULTIOBASE 0x300
//I/O Base Address Register
#define PP_IOBASE 0x0020
// PP_RxCFG - Receive Configuration and Interrupt Mask bit definition - Read/write
#define SKIP_1 0x0040
#define RX_STREAM_ENBL 0x0080
#define RX_OK_ENBL 0x0100
#define RX_DMA_ONLY 0x0200
#define AUTO_RX_DMA 0x0400
#define BUFFER_CRC 0x0800
#define RX_CRC_ERROR_ENBL 0x1000
#define RX_RUNT_ENBL 0x2000
#define RX_EXTRA_DATA_ENBL 0x4000
// PP_RxCTL - Receive Control bit definition - Read/write
#define RX_IA_HASH_ACCEPT 0x0040
#define RX_PROM_ACCEPT 0x0080
#define RX_OK_ACCEPT 0x0100
#define RX_MULTCAST_ACCEPT 0x0200
#define RX_IA_ACCEPT 0x0400
#define RX_BROADCAST_ACCEPT 0x0800
#define RX_BAD_CRC_ACCEPT 0x1000
#define RX_RUNT_ACCEPT 0x2000
#define RX_EXTRA_DATA_ACCEPT 0x4000
// PP_TxCFG - Transmit Configuration Interrupt Mask bit definition - Read/write
#define TX_LOST_CRS_ENBL 0x0040
#define TX_SQE_ERROR_ENBL 0x0080
#define TX_OK_ENBL 0x0100
#define TX_LATE_COL_ENBL 0x0200
#define TX_JBR_ENBL 0x0400
#define TX_ANY_COL_ENBL 0x0800
#define TX_16_COL_ENBL 0x8000
// PP_TxCMD - Transmit Command bit definition - Read-only and
// PP_TxCommand - Write-only (PacketPage+0144h)
#define TX_START_5_BYTES 0x0000
#define TX_START_381_BYTES 0x0040
#define TX_START_1021_BYTES 0x0080
#define TX_START_ALL_BYTES 0x00C0
#define TX_FORCE 0x0100
#define TX_ONE_COL 0x0200
#define TX_NO_CRC 0x1000
#define TX_RUNT 0x2000
// PP_BufCFG - Buffer Configuration Interrupt Mask bit definition - Read/write
#define GENERATE_SW_INTERRUPT 0x0040
#define RX_DMA_ENBL 0x0080
#define READY_FOR_TX_ENBL 0x0100
#define TX_UNDERRUN_ENBL 0x0200
#define RX_MISS_ENBL 0x0400
#define RX_128_BYTE_ENBL 0x0800
#define TX_COL_COUNT_OVRFLOW_ENBL 0x1000
#define RX_MISS_COUNT_OVRFLOW_ENBL 0x2000
#define RX_DEST_MATCH_ENBL 0x8000
// PP_LineCTL - Line Control bit definition - Read/write
#define SERIAL_RX_ON 0x0040
#define SERIAL_TX_ON 0x0080
#define AUI_ONLY 0x0100
#define AUTO_AUI_10BASET 0x0200
#define MODIFIED_BACKOFF 0x0800
#define NO_AUTO_POLARITY 0x1000
#define TWO_PART_DEFDIS 0x2000
#define LOW_RX_SQUELCH 0x4000
// PP_SelfCTL - Software Self Control bit definition - Read/write
#define POWER_ON_RESET 0x0040
#define SW_STOP 0x0100
#define SLEEP_ON 0x0200
#define AUTO_WAKEUP 0x0400
#define HCB0_ENBL 0x1000
#define HCB1_ENBL 0x2000
#define HCB0 0x4000
#define HCB1 0x8000
// PP_BusCTL - ISA Bus Control bit definition - Read/write
#define RESET_RX_DMA 0x0040
#define MEMORY_ON 0x0400
#define DMA_BURST_MODE 0x0800
#define IO_CHANNEL_READY_ON 0x1000
#define RX_DMA_SIZE_64K 0x2000
#define ENABLE_IRQ 0x8000
// PP_TestCTL - Test Control bit definition - Read/write
#define LINK_OFF 0x0080
#define ENDEC_LOOPBACK 0x0200
#define AUI_LOOPBACK 0x0400
#define BACKOFF_OFF 0x0800
#define FDX_8900 0x4000
// PP_RxEvent - Receive Event Bit definition - Read-only
#define RX_IA_HASHED 0x0040
#define RX_DRIBBLE 0x0080
#define RX_OK 0x0100
#define RX_HASHED 0x0200
#define RX_IA 0x0400
#define RX_BROADCAST 0x0800
#define RX_CRC_ERROR 0x1000
#define RX_RUNT 0x2000
#define RX_EXTRA_DATA 0x4000
#define HASH_INDEX_MASK 0xFC00 // Hash-Table Index Mask (6 Bit)
// PP_TxEvent - Transmit Event Bit definition - Read-only
#define TX_LOST_CRS 0x0040
#define TX_SQE_ERROR 0x0080
#define TX_OK 0x0100
#define TX_LATE_COL 0x0200
#define TX_JBR 0x0400
#define TX_16_COL 0x8000
#define TX_COL_COUNT_MASK 0x7800
// PP_BufEvent - Buffer Event Bit definition - Read-only
#define SW_INTERRUPT 0x0040
#define RX_DMA 0x0080
#define READY_FOR_TX 0x0100
#define TX_UNDERRUN 0x0200
#define RX_MISS 0x0400
#define RX_128_BYTE 0x0800
#define TX_COL_OVRFLW 0x1000
#define RX_MISS_OVRFLW 0x2000
#define RX_DEST_MATCH 0x8000
// PP_LineST - Ethernet Line Status bit definition - Read-only
#define LINK_OK 0x0080
#define AUI_ON 0x0100
#define TENBASET_ON 0x0200
#define POLARITY_OK 0x1000
#define CRS_OK 0x4000
// PP_SelfST - Chip Software Status bit definition
#define ACTIVE_33V 0x0040
#define INIT_DONE 0x0080
#define SI_BUSY 0x0100
#define EEPROM_PRESENT 0x0200
#define EEPROM_OK 0x0400
#define EL_PRESENT 0x0800
#define EE_SIZE_64 0x1000
// PP_BusST - ISA Bus Status bit definition
#define TX_BID_ERROR 0x0080
#define READY_FOR_TX_NOW 0x0100
// The following block defines the ISQ event types
#define ISQ_RX_EVENT 0x0004
#define ISQ_TX_EVENT 0x0008
#define ISQ_BUFFER_EVENT 0x000C
#define ISQ_RX_MISS_EVENT 0x0010
#define ISQ_TX_COL_EVENT 0x0012
#define ISQ_EVENT_MASK 0x003F // ISQ mask to find out type of event
// Ports for I/O-Mode
#define RX_FRAME_PORT 0x0000
#define TX_FRAME_PORT 0x0000
#define TX_CMD_PORT 0x0004
#define TX_LEN_PORT 0x0006
#define ISQ_PORT 0x0008
#define ADD_PORT 0x000A
#define DATA_PORT 0x000C
#define AUTOINCREMENT 0x8000 // Bit mask to set Bit-15 for autoincrement
// prototypes
void TCP_Init(void);
Uint16 Rdy4Tx(void);
void Init8900(void);
void TCP_Listen(void);
//Uint16 VerifyTCP(void);
void TCP_Syn_Rec(void);
void TCP_Syn_Sent(void);
void TCP_Last_Ack(void);
//void Resend_Packet(void);
void Delete_Socket(void);
void DoNetworkStuff(Uint16 Temp);
void TCP_Close_Wait(void);
void SendEthnetFrame(void);
void TCP_Established(void);
Uint16 ReadFrame8900(void);
void ProcessEthIAFrame(void);
void Process_TCP_Timeout(void);
void Process_ICMP_Frame(void);
void Prepare_ICMP_Answer(void);
void Process_TCP_Frame(void);
Uint16 Read8900(Uint16 Address);
void WriteFrame8900(Uint16 Data);
void CopyToFrame8900(Uint16 Size);
void RequestSend(Uint16 FrameSize);
void ProcessEthBroadcastFrame(void);
void DummyReadFrame8900(Uint16 Size);
void Prepare_TCP_Frame(Uint16 TCPCode);
void Write8900(Uint16 Address, Uint16 Data);
void Prepare_UDP_Frame(Uint16 RemoteUdpPort,Uint16 TxUDPDataNum);
void CopyFrameFrom8900(Uint16 OffsetNum,Uint16 Size);
Uint16 CalcCheckSum(Uint16 *Start, Uint16 Count, Uint16 IsTCP, Uint16 IsUDP);
void TCPActiveOpen(void);
#endif
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -