commonio

嵌入式系统设计与实例开发实验教材二源码 多线程应用程序设计 串行端口程序设计 AD接口实验 CAN总线通信实验 GPS通信实验 Linux内核移植与编译实验 IC卡读写实验 SD驱动使

S/390 common I/O-Layer - command line parameters and /proc entries
==================================================================

Command line parameters
-----------------------

* cio_msg = yes | no
  
  Determines whether information on found devices and sensed device 
  characteristics should be shown during startup, i. e. messages of the types 
  "Detected device 4711 on subchannel 42" and "SenseID: Device 4711 reports: ...".

  Default is off.


* cio_notoper_msg = yes | no

  Determines whether messages of the type "Device 4711 became 'not operational'"
  should be shown during startup; after startup, they will always be shown.
  
  Default is on.


* cio_ignore = <range of device numbers>, <range of device numbers>, ...

  The given device numbers will be ignored by the common I/O-layer; no detection
  and device sensing will be done on any of those devices. The subchannel to 
  which the device in question is attached will be treated as if no device was
  attached.

  An ignored device can be un-ignored later; see the "/proc entries"-section for
  details.

  The device numbers must be given hexadecimal.

  For example, 
	cio_ignore=0x23-0x42,0x4711
  will ignore all devices with device numbers ranging from 23 to 42 and the 
  device with device number 4711, if detected.

  By default, no devices are ignored.


* cio_proc_devinfo = yes | no

  Determines whether the entries under /proc/deviceinfo/ (see below) should be
  created. Since there are problems with systems with many devices attached, I
  made it configurable.

  Until the problems are dealt with, default is off.


/proc entries
-------------

* /proc/subchannels

  Shows for each subchannel
  - device number
  - device type/model and if applicable control unit type/model
  - whether the device is in use
  - path installed mask, path available mask, path operational mask and last 
    path used mask
  - the channel path IDs (chpids)


* /proc/deviceinfo/

  Shows in subdirectories for each device some characteristics:
  - /proc/deviceinfo/<devno>/chpids: 
	the channel path IDs
  - /proc/deviceinfo/<devno>/in_use: 
	whether the device is in use
  - /proc/deviceinfo/<devno>/sensedata:
    	the device type/model and if applicable control unit type/model of the
	device

  NOTE: Since the number of inodes which can be dynamically allocated by procfs
        is limited, device entries will only be created up to a magic number of
        devices. The kernel will utter a warning that not all entries can be
        created. In this case, you shouldn't use "cio_proc_devinfo=yes" (see
        above).

* /proc/cio_ignore

  Lists the ranges of device numbers which are ignored by common I/O.

  You can un-ignore certain or all devices by piping to /proc/cio_ignore. 
  "free all" will un-ignore all ignored devices, 
  "free <devnorange>, <devnorange>, ..." will un-ignore the specified devices.

  For example, if devices 23 to 42 and 4711 are ignored,
  - echo free 0x30-0x32 > /proc/cio_ignore
    will un-ignore devices 30 to 32 and will leave devices 23 to 2F, 33 to 42
    and 4711 ignored;
  - echo free 0x41 > /proc/cio_ignore will furthermore un-ignore device 41;
  - echo free all > /proc/cio_ignore will un-ignore all remaining ignored 
    devices.

  When a device is un-ignored, device recognition and sensing is performed and 
  the device driver will be notified if possible, so the device will become
  available to the system.

  You can also add ranges of devices to be ignored by piping to 
  /proc/cio_ignore; "add <devnorange>, <devnorange>, ..." will ignore the 
  specified devices.

  Note: Already known devices cannot be ignored; this also applies to devices
        which are gone after a machine check.

  For example, if device abcd is already known and all other devices a000-afff 
  are not known, "echo add 0xa000-0xaccc, 0xaf00-0xafff > /proc/cio_ignore" 
  will add af00-afff to the list of ignored devices and skip a000-accc.


* /proc/s390dbf/cio_*/ (S/390 debug feature)

  Some views generated by the debug feature to hold various debug outputs.

  - /proc/s390dbf/cio_crw/sprintf
    Messages from the processing of pending channel report words (machine check
    handling), which will also show when CONFIG_DEBUG_CRW is defined.

  - /proc/s390dbf/cio_msg/sprintf
    Various debug messages from the common I/O-layer; generally, messages which 
    will also show when CONFIG_DEBUG_IO is defined.

  - /proc/s390dbf/cio_trace/hex_ascii
    Logs the calling of functions in the common I/O-layer and, if applicable, 
    which subchannel they were called for.

  The level of logging can be changed to be more or less verbose by piping to 
  /proc/s390dbf/cio_*/level a number between 0 and 6; see the documentation on
  the S/390 debug feature (Documentation/s390/s390dbf.txt) for details.

* /proc/irq_count

  This entry counts how many times s390_process_IRQ has been called for each 
  CPU. This info is in /proc/interrupts on other architectures.