lcd_config.h

44b0+s6b0724包括系统初始化

#ifndef	__LCD_CONFIG_h__
#define	__LCD_CONFIG_h__
//	write your header here
#define LCD_X_MAX			128-1			//屏幕的X轴的物理宽度
#define LCD_Y_MAX			64-1			//屏幕的Y轴的物理宽度
			
#define LCD_XY_Switch		0				//显示时X轴和Y由交换
#define LCD_X_Rev			0				//显示时X轴反转
#define LCD_Y_Rev			0				//显示时Y轴反转

#if LCD_XY_Switch == 0
	#define Dis_X_MAX		LCD_X_MAX
	#define Dis_Y_MAX		LCD_Y_MAX	
#endif

#if LCD_XY_Switch == 1
	#define Dis_X_MAX		LCD_Y_MAX
	#define Dis_Y_MAX		LCD_X_MAX	
#endif

#define LCD_INITIAL_COLOR	0x00ff			//定义LCD屏初始化时的背景色0x0000

//以下定义为针对于cpu的功能指令进行定义的，局部可修改~
//LCD供电电平选择
#define		M_LCD_VDD_SET	M_LCD_SETR_7//M_LCD_SETR_5		//3.3V供电时选此二项
#define		M_LCD_VDD		M_LCD_BIAS_7//....
//#define		M_LCD_VDD_SET	M_LCD_SETR_4	//5.0V供电时选此二项
//#define		M_LCD_VDD		M_LCD_BIAS_9	//...
//LCD指令
//LCD开关命令
#define		M_LCD_ON		0x00af
#define		M_LCD_OFF		0x00ae
//设置上电控制模式
#define		M_LCD_POWER_BC	0x002c
#define		M_LCD_POWER_VR	0x002a
#define		M_LCD_POWER_VC	0x0029
#define		M_LCD_POWER_ALL	0x002f
//V5内部电压调节电阻设置……
#define		M_LCD_SETR_0	0x0020
#define		M_LCD_SETR_1	0x0021
#define		M_LCD_SETR_2	0x0022
#define		M_LCD_SETR_3	0x0023
#define		M_LCD_SETR_4	0x0024
#define		M_LCD_SETR_5	0x0025
#define		M_LCD_SETR_6	0x0026
#define		M_LCD_SETR_7	0x0027
//...end
#define		M_LCD_ELE_VOL	0x0081		//电量设置模式（显示亮度）
//偏压设置
#define		M_LCD_BIAS_9	0x00a2		//V5时选此选项设置
#define		M_LCD_BIAS_7	0x00a1		//V3时选此选项设置
//Com 扫描方式设置命令
#define		M_LCD_COM_NOR	0x00c0		//正常方式
#define		M_LCD_COM_REV	0x00c8		//反相
//Segment方向选择
#define		M_LCD_SEG_NOR	0x00a0		//正常
#define		M_LCD_SEG_REV	0x00a1		//反向
//全屏点亮/变暗指令
#define		M_LCD_ALL_LIGNT	0x00a5		//LCD ALL paint ON
#define		M_LCD_ALL_LOW	0x00a4		//Normal Display mode
//正相反相显示控制指令，RAM中数据不变
#define		M_LCD_ALL_NOR	0x00a6		//正相
#define		M_LCD_ALL_REV	0x00a7		//反相
//静态指示器控制指令
#define		M_LCD_STATIC_ON	0x00ad		//ON
#define		M_LCD_STATIC_OFF 0x00ac		//OFF
//设置显示起始行对应RAM行号
#define		M_LCD_BEGIN_LINE 0x0040		//基数，后面可加的尾数可为0~63
//设置当前页基数
#define		M_LCD_COL_PAGE	0x00b0		//基数指令，后可加尾数0~8
//设置当前列基数
#define		M_LCD_COL_LINE_LOW	0x0004		//基数指令，低四位有效
#define		M_LCD_COL_LINE_HIG	0x0010		//基数指令，低四位有效


#endif