ftp.txt

本程序为在linux下实现FTP传输文件的实现

                                            -------------
                                            |/---------\|
                                            ||   User  ||    --------
                                            ||Interface|<--->| User |
                                            |\----^----/|    --------
                  ----------                |     |     |
                  |/------\|  FTP Commands  |/----V----\|
                  ||Server|<---------------->|   User  ||
                  ||  PI  ||   FTP Replies  ||    PI   ||
                  |\--^---/|                |\----^----/|
                  |   |    |                |     |     |
      --------    |/--V---\|      Data      |/----V----\|    --------
      | File |<--->|Server|<---------------->|  User   |<--->| File |
      |System|    || DTP  ||   Connection   ||   DTP   ||    |System|
      --------    |\------/|                |\---------/|    --------
                  ----------                -------------

                  Server-FTP                   USER-FTP
                  
  4.1.  FTP COMMANDS

      4.1.1.  ACCESS CONTROL COMMANDS

         The following commands specify access control identifiers
         (command codes are shown in parentheses).

         USER NAME (USER)

            The argument field is a Telnet string identifying the user.
            The user identification is that which is required by the
            server for access to its file system.  This command will
            normally be the first command transmitted by the user after
            the control connections are made (some servers may require
            this).  Additional identification information in the form of
            a password and/or an account command may also be required by
            some servers.  Servers may allow a new USER command to be
            entered at any point in order to change the access control
            and/or accounting information.  This has the effect of
            flushing any user, password, and account information already
            supplied and beginning the login sequence again.  All
            transfer parameters are unchanged and any file transfer in
            progress is completed under the old access control
            parameters.






Postel & Reynolds                                              [Page 25]


                                                                        
RFC 959                                                     October 1985
File Transfer Protocol


         PASSWORD (PASS)

            The argument field is a Telnet string specifying the user's
            password.  This command must be immediately preceded by the
            user name command, and, for some sites, completes the user's
            identification for access control.  Since password
            information is quite sensitive, it is desirable in general
            to "mask" it or suppress typeout.  It appears that the
            server has no foolproof way to achieve this.  It is
            therefore the responsibility of the user-FTP process to hide
            the sensitive password information.

         ACCOUNT (ACCT)

            The argument field is a Telnet string identifying the user's
            account.  The command is not necessarily related to the USER
            command, as some sites may require an account for login and
            others only for specific access, such as storing files.  In
            the latter case the command may arrive at any time.

            There are reply codes to differentiate these cases for the
            automation: when account information is required for login,
            the response to a successful PASSword command is reply code
            332.  On the other hand, if account information is NOT
            required for login, the reply to a successful PASSword
            command is 230; and if the account information is needed for
            a command issued later in the dialogue, the server should
            return a 332 or 532 reply depending on whether it stores
            (pending receipt of the ACCounT command) or discards the
            command, respectively.

         CHANGE WORKING DIRECTORY (CWD)

            This command allows the user to work with a different
            directory or dataset for file storage or retrieval without
            altering his login or accounting information.  Transfer
            parameters are similarly unchanged.  The argument is a
            pathname specifying a directory or other system dependent
            file group designator.

         CHANGE TO PARENT DIRECTORY (CDUP)

            This command is a special case of CWD, and is included to
            simplify the implementation of programs for transferring
            directory trees between operating systems having different




Postel & Reynolds                                              [Page 26]


                                                                        
RFC 959                                                     October 1985
File Transfer Protocol


            syntaxes for naming the parent directory.  The reply codes
            shall be identical to the reply codes of CWD.  See
            Appendix II for further details.

         STRUCTURE MOUNT (SMNT)

            This command allows the user to mount a different file
            system data structure without altering his login or
            accounting information.  Transfer parameters are similarly
            unchanged.  The argument is a pathname specifying a
            directory or other system dependent file group designator.

         REINITIALIZE (REIN)

            This command terminates a USER, flushing all I/O and account
            information, except to allow any transfer in progress to be
            completed.  All parameters are reset to the default settings
            and the control connection is left open.  This is identical
            to the state in which a user finds himself immediately after
            the control connection is opened.  A USER command may be
            expected to follow.

         LOGOUT (QUIT)

            This command terminates a USER and if file transfer is not
            in progress, the server closes the control connection.  If
            file transfer is in progress, the connection will remain
            open for result response and the server will then close it.
            If the user-process is transferring files for several USERs
            but does not wish to close and then reopen connections for
            each, then the REIN command should be used instead of QUIT.

            An unexpected close on the control connection will cause the
            server to take the effective action of an abort (ABOR) and a
            logout (QUIT).

      4.1.2.  TRANSFER PARAMETER COMMANDS

         All data transfer parameters have default values, and the
         commands specifying data transfer parameters are required only
         if the default parameter values are to be changed.  The default
         value is the last specified value, or if no value has been
         specified, the standard default value is as stated here.  This
         implies that the server must "remember" the applicable default
         values.  The commands may be in any order except that they must
         precede the FTP service request.  The following commands
         specify data transfer parameters:


Postel & Reynolds                                              [Page 27]


                                                                        
RFC 959                                                     October 1985
File Transfer Protocol


         DATA PORT (PORT)

            The argument is a HOST-PORT specification for the data port
            to be used in data connection.  There are defaults for both
            the user and server data ports, and under normal
            circumstances this command and its reply are not needed.  If
            this command is used, the argument is the concatenation of a
            32-bit internet host address and a 16-bit TCP port address.
            This address information is broken into 8-bit fields and the
            value of each field is transmitted as a decimal number (in
            character string representation).  The fields are separated
            by commas.  A port command would be:

               PORT h1,h2,h3,h4,p1,p2

            where h1 is the high order 8 bits of the internet host
            address.

         PASSIVE (PASV)

            This command requests the server-DTP to "listen" on a data
            port (which is not its default data port) and to wait for a
            connection rather than initiate one upon receipt of a
            transfer command.  The response to this command includes the
            host and port address this server is listening on.

         REPRESENTATION TYPE (TYPE)

            The argument specifies the representation type as described
            in the Section on Data Representation and Storage.  Several
            types take a second parameter.  The first parameter is
            denoted by a single Telnet character, as is the second
            Format parameter for ASCII and EBCDIC; the second parameter
            for local byte is a decimal integer to indicate Bytesize.
            The parameters are separated by a <SP> (Space, ASCII code
            32).

            The following codes are assigned for type:

                         \    /
               A - ASCII |    | N - Non-print
                         |-><-| T - Telnet format effectors
               E - EBCDIC|    | C - Carriage Control (ASA)
                         /    \
               I - Image
               
               L <byte size> - Local byte Byte size


Postel & Reynolds                                              [Page 28]


                                                                        
RFC 959                                                     October 1985
File Transfer Protocol


            The default representation type is ASCII Non-print.  If the
            Format parameter is changed, and later just the first
            argument is changed, Format then returns to the Non-print
            default.

         FILE STRUCTURE (STRU)

            The argument is a single Telnet character code specifying
            file structure described in the Section on Data
            Representation and Storage.

            The following codes are assigned for structure:

               F - File (no record structure)
               R - Record structure
               P - Page structure

            The default structure is File.

         TRANSFER MODE (MODE)

            The argument is a single Telnet character code specifying
            the data transfer modes described in the Section on
            Transmission Modes.

            The following codes are assigned for transfer modes:

               S - Stream
               B - Block
               C - Compressed

            The default transfer mode is Stream.

      4.1.3.  FTP SERVICE COMMANDS

         The FTP service commands define the file transfer or the file
         system function requested by the user.  The argument of an FTP
         service command will normally be a pathname.  The syntax of
         pathnames must conform to server site conventions (with
         standard defaults applicable), and the language conventions of
         the control connection.  The suggested default handling is to
         use the last specified device, directory or file name, or the
         standard default defined for local users.  The commands may be
         in any order except that a "rename from" command must be
         followed by a "rename to" command and the restart command must
         be followed by the interrupted service command (e.g., STOR or
         RETR).  The data, when transferred in response to FTP service


Postel & Reynolds                                              [Page 29]


                                                                        
RFC 959                                                     October 1985
File Transfer Protocol


         commands, shall always be sent over the data connection, except
         for certain informative replies.  The following commands
         specify FTP service requests:

         RETRIEVE (RETR)

            This command causes the server-DTP to transfer a copy of the
            file, specified in the pathname, to the server- or user-DTP
            at the other end of the data connection.  The status and
            contents of the file at the server site shall be unaffected.

         STORE (STOR)

            This command causes the server-DTP to accept the data
            transferred via the data connection and to store the data as
            a file at the server site.  If the file specified in the
            pathname exists at the server site, then its contents shall
            be replaced by the data being transferred.  A new file is
            created at the server site if the file specified in the
            pathname does not already exist.

         STORE UNIQUE (STOU)

            This command behaves like STOR except that the resultant
            file is to be created in the current directory under a name
            unique to that directory.  The 250 Transfer Started response
            must include the name generated.