ds18b20.i

cvavr ds18b20源程序及仿真的例子,修正了cvavr中显示负温度时出的错误

/* Multipoint thermometer with LCD display
   using the Maxim DS18B20
   1 Wire bus temperature sensors

   CodeVisionAVR C Compiler
   (C) 2000-2005 HP InfoTech S.R.L.
   www.hpinfotech.ro

   Chip: ATmega8515
   Memory Model: SMALL
   Data Stack Size: 128 bytes
   
   THE ATmega8515 CLOCK FREQUENCY MUST BE 3.6864 MHz

   The DS18B20 sensors are connected to
   bit 6 of PORTA of the ATmega8515 as follows:

   [DS18B20]     [STK500 PORTA HEADER]
    1 GND         -   9  GND
    2 DQ          -   7  PA6
    3 VDD         -  10 +5V

   All the temperature sensors must be connected
   in parallel
   
   AN 4.7k PULLUP RESISTOR MUST BE CONNECTED
   BETWEEN DQ (PA6) AND +5V !
*/
#asm
    .equ __w1_port=0x1b
    .equ __w1_bit=6
#endasm

/* Use an 2x16 alphanumeric LCD connected
   to PORTC as follows:

  [LCD]   [STK500 PORTC HEADER]
   1 GND- 9  GND
   2 +5V- 10 VCC  
   3 VLC- LCD contrast control voltage 0..1V
   4 RS - 1  PC0
   5 RD - 2  PC1
   6 EN - 3  PC2
  11 D4 - 5  PC4
  12 D5 - 6  PC5
  13 D6 - 7  PC6
  14 D7 - 8  PC7
*/

#asm
    .equ __lcd_port=0x15
#endasm

/* LCD driver routines

  CodeVisionAVR C Compiler
  (C) 1998-2003 Pavel Haiduc, HP InfoTech S.R.L.

  BEFORE #include -ING THIS FILE YOU
  MUST DECLARE THE I/O ADDRESS OF THE
  DATA REGISTER OF THE PORT AT WHICH
  THE LCD IS CONNECTED!

  EXAMPLE FOR PORTB:

    #asm
        .equ __lcd_port=0x18
    #endasm
    #include <lcd.h>

*/


#pragma used+

void _lcd_ready(void);
void _lcd_write_data(unsigned char data);
// write a byte to the LCD character generator or display RAM
void lcd_write_byte(unsigned char addr, unsigned char data);
// read a byte from the LCD character generator or display RAM
unsigned char lcd_read_byte(unsigned char addr);
// set the LCD display position  x=0..39 y=0..3
void lcd_gotoxy(unsigned char x, unsigned char y);
// clear the LCD
void lcd_clear(void);
void lcd_putchar(char c);
// write the string str located in SRAM to the LCD
void lcd_puts(char *str);
// write the string str located in FLASH to the LCD
void lcd_putsf(char flash *str);
// initialize the LCD controller
unsigned char lcd_init(unsigned char lcd_columns);

#pragma used-
#pragma library lcd.lib


/*
  CodeVisionAVR C Compiler
  (C) 1998-2005 Pavel Haiduc, HP InfoTech S.R.L.

  Prototypes for Dallas Semiconductor
  DS18B20 1 Wire bus temperature sensor
  functions

  BEFORE #include -ING THIS FILE YOU
  MUST DECLARE THE I/O ADDRESS OF THE
  DATA REGISTER OF THE PORT AT WHICH
  THE 1 WIRE BUS IS CONNECTED AND
  THE DATA BIT USED

  EXAMPLE FOR PORTB:

    #asm
        .equ __w1_port=0x18
        .equ __w1_bit=3
    #endasm
    #include <ds1820.h>
*/


/*
  CodeVisionAVR C Compiler
  (C) 1998-2000 Pavel Haiduc, HP InfoTech S.R.L.

  Prototypes for Dallas Semiconductor
  1 Wire protocol functions

  BEFORE #include -ING THIS FILE YOU
  MUST DECLARE THE I/O ADDRESS OF THE
  DATA REGISTER OF THE PORT AT WHICH
  THE 1 WIRE BUS IS CONNECTED AND
  THE DATA BIT USED

  EXAMPLE FOR PORTB:

    #asm
        .equ __w1_port=0x18
        .equ __w1_bit=3
    #endasm
    #include <1wire.h>
*/


#pragma used+
unsigned char w1_init(void);
unsigned char w1_read(void);
unsigned char w1_write(unsigned char data);
unsigned char w1_search(unsigned char cmd,void *p);
unsigned char w1_dow_crc8(void *p,unsigned char n);
#pragma used-





#pragma used+
extern struct __ds18b20_scratch_pad_struct
       {
       unsigned char temp_lsb,temp_msb,
                temp_high,temp_low,
                conf_register,
                res1,
                res2,
                res3,
                crc;
       } __ds18b20_scratch_pad;

unsigned char ds18b20_select(unsigned char *addr);
unsigned char ds18b20_read_spd(unsigned char *addr);
float ds18b20_temperature(unsigned char *addr);
unsigned char ds18b20_init(unsigned char *addr,signed char temp_low,signed char temp_high,
unsigned char resolution);
#pragma used-

#pragma library ds18b20.lib


// CodeVisionAVR C Compiler
// (C) 1998-2000 Pavel Haiduc, HP InfoTech S.R.L.


#pragma used+

void delay_us(unsigned int n);
void delay_ms(unsigned int n);

#pragma used-

// CodeVisionAVR C Compiler
// (C) 1998-2006 Pavel Haiduc, HP InfoTech S.R.L.

// Prototypes for standard I/O functions


// CodeVisionAVR C Compiler
// (C) 1998-2002 Pavel Haiduc, HP InfoTech S.R.L.

// Variable length argument list macros



typedef char *va_list;





#pragma used+

char getchar(void);
void putchar(char c);
void puts(char *str);
void putsf(char flash *str);

char *gets(char *str,unsigned int len);

void printf(char flash *fmtstr,...);
void sprintf(char *str, char flash *fmtstr,...);
void snprintf(char *str, unsigned int size, char flash *fmtstr,...);
void vprintf (char flash * fmtstr, va_list argptr);
void vsprintf (char *str, char flash * fmtstr, va_list argptr);
void vsnprintf (char *str, unsigned int size, char flash * fmtstr, va_list argptr);
signed char scanf(char flash *fmtstr,...);
signed char sscanf(char *str, char flash *fmtstr,...);




                                   

            


#pragma used-

#pragma library stdio.lib



char lcd_buffer[33];


main()
{
//unsigned char i,j,devices;
float aa;
lcd_init(16);
lcd_putsf("CodeVisionAVR\n1 Wire Bus Demo");
delay_ms(2000);
lcd_clear();

    if(ds18b20_init(0,25,35,3 )==0)
       {
      
       while (1); /* stop here if init error */
       };

   
while (1)
      {
      //j=1;
      //for (i=0;i<1;i++)
        //  {  
        aa=ds18b20_temperature(0); 
        if(aa>125) 
        sprintf(lcd_buffer,"t=%+.1f\xdfC",aa-4096);
        else
          sprintf(lcd_buffer,"t=%+.1f\xdfC",aa);
          lcd_clear();
          lcd_puts(lcd_buffer);
          delay_ms(500);
          //};
      };
}