zl5011xmm.c

Zalink50114----TDMoIP芯片驱动源码

         extMemBurstLength, 0, 0, 0, 0, 0);

   if ((extMemBurstLength < ZL5011X_MM_MIN_BURST_LENGTH) ||
      (extMemBurstLength > ZL5011X_MM_MAX_BURST_LENGTH))
   {
      status = ZL5011X_PARAMETER_INVALID;
   }

   if (status == ZL5011X_OK)
   {
      status = zl5011xWrite(zl5011xParams, ZL5011X_MM_BURSTL, extMemBurstLength);
      zl5011xParams->packetMemory.extMemBurstLength = extMemBurstLength;
   }
   return(status);
}

/*******************************************************************************

 Function:
    zl5011xMmTestPacketMemory

 Description:
   This function runs a software test on the packet memory, returning a bad
   status on error. Test mem by writing a counting value to successive locations,
   first counting up then repeat counting down (invert count).

 Inputs:
    zl5011xParams  Pointer to the structure for this device instance
   startAddr      start address,
   memSize        in bytes

 Outputs:
    none

 Returns:
   zlStatusE

 Remarks:

*******************************************************************************/
extern zlStatusE zl5011xMmTestPacketMemory(zl5011xParamsS *zl5011xParams, Uint32T startAddr, Uint32T memSize)
{
   zlStatusE status = ZL5011X_OK;
   zlStatusE result = ZL5011X_OK;
   Uint32T  count = 0, reso = sizeof(Uint32T);
   Uint32T writeValue = 0, readValue = 0xFFFFFFFF;
   Uint8T inverted;

#ifdef _DEBUG
   Uint32T traceFnFilterTemp;

   traceFnFilterTemp = zl5011xTraceFnFilter;

   /* turn off the read and write traces for the duration of the memory test */
   zl5011xTraceFnFilter &= ~(ZL5011X_READ | ZL5011X_WRITE);
#endif

   ZL5011X_TRACE(ZL5011X_MM_FN_ID, "zl5011xMmTestPacketMemory: start 0x%08x, memSize 0x%08x", startAddr, memSize, 0, 0, 0, 0);


   /* loop twice: first with count then inverted count */
   for(inverted = 0; inverted <= 1; inverted++)
   {
      if ((status!= ZL5011X_OK) || (result!= ZL5011X_OK))
      {
         break;
      }

      /* write to all specified locations */
      readValue = 0xFFFFFFFF;
      for(count = 0; count< memSize; count+= reso)
      {
         if (inverted == 0)
         {
            writeValue = count;
         }
         else
         {
            writeValue = ~count;
         }
         status = zl5011xWrite(zl5011xParams, count+ startAddr, writeValue);
      }

      /* check all mem locations */
      for(count = 0; count< memSize; count+= reso)
      {
         if ((status!= ZL5011X_OK) || (result!= ZL5011X_OK))
         {
            break;
         }
         if (inverted == 0)
         {
            writeValue = count;
         }
         else
         {
            writeValue = ~count;
         }
         status = zl5011xRead(zl5011xParams, count+ startAddr, &readValue);
         if (writeValue != readValue)
         {
            result = ZL5011X_PACKET_MEMORY_FAIL;
         }
      }
   }
   if (result == ZL5011X_OK)
   {
      ZL5011X_TRACE(ZL5011X_MM_FN_ID, "zl5011xMmTestPacketMemory: PASSED ", 0, 0, 0, 0, 0, 0);
   }
   else
   {
      ZL5011X_TRACE(ZL5011X_MM_FN_ID, "zl5011xMmTestPacketMemory: FAILED at address 0x%08x,"
                            " counting up(0)/down(1)=%d,  expected 0x%08x, "
                            " read 0x%08x",
                            count+ startAddr, inverted, writeValue, readValue, 0, 0);
   }

#ifdef _DEBUG
   /* the memory test is finished, so restore the settings for the read and write traces */
   zl5011xTraceFnFilter = traceFnFilterTemp;
#endif

   return(status);
}


/*******************************************************************************

 Function:
    zl5011xMmControlExternalMemory

 Description:
   This function can be used to put the external memory into low power modes.

 Inputs:
    zl5011xParams     Pointer to the structure for this device instance
    extMemReadiness  disable, sleep, enable

 Outputs:
    none

 Returns:
   zlStatusE

 Remarks:

*******************************************************************************/
extern zlStatusE zl5011xMmControlExternalMemory(zl5011xParamsS *zl5011xParams,
                                        zl5011xExtMemReadinessE extMemReadiness)
{
   zlStatusE status = ZL5011X_OK;

   ZL5011X_TRACE(ZL5011X_MM_FN_ID,
         "zl5011xMmControlExternalMemory: %d ",
         extMemReadiness, 0, 0, 0, 0, 0);

   if ((extMemReadiness>= ZL5011X_MM_DISABLED) && (extMemReadiness <= ZL5011X_MM_SLEEP))
   {
      status = zl5011xWrite(zl5011xParams, ZL5011X_MM_EMEMENB, extMemReadiness);
   }
   else
   {
      status = ZL5011X_PARAMETER_INVALID;
   }

   if (status == ZL5011X_OK)
   {
      zl5011xParams->packetMemory.extMemReadiness = extMemReadiness;
   }

   return(status);
}

/*******************************************************************************
 Function:
    zl5011xMmSetParityMode

 Description:
   This function sets parity of ext memory

 Inputs:
    zl5011xParams  Pointer to the structure for this device instance
    extMemParity  none, odd, OR even

 Outputs:
    none

 Returns:
   zlStatusE

 Remarks:

*******************************************************************************/

extern zlStatusE zl5011xMmSetParityMode(zl5011xParamsS *zl5011xParams,
      zl5011xExtMemParityE extMemParity)
{
   zlStatusE status = ZL5011X_OK;

   ZL5011X_TRACE(ZL5011X_MM_FN_ID, "zl5011xMmSetParityMode: %d ",
         extMemParity, 0, 0, 0, 0, 0);

   switch (extMemParity)
   {
      case ZL5011X_MM_PARITY_NONE:       /* fall through intended */
      case ZL5011X_MM_PARITY_ODD:        /* fall through intended */
      case ZL5011X_MM_PARITY_EVEN:
         status = zl5011xWrite(zl5011xParams, ZL5011X_MM_EMEMPARITY1, extMemParity);
         break;

      default:
         status = ZL5011X_PARAMETER_INVALID;
         break;
   }

   if (status == ZL5011X_OK)
   {
      zl5011xParams->packetMemory.extMemParity = extMemParity;
   }

   return(status);
}

/*******************************************************************************

 Function:
    zl5011xMmSetParityErrorThreshold

 Description:
   This function sets the parity trip point.

 Inputs:
    zl5011xParams           Pointer to the structure for this device instance
    extMemParityTripPoint  number of parity failures that cause an interrupt.

 Outputs:
    none

 Returns:
   zlStatusE

 Remarks:
   Also resets the parity count to 0, to give a known start condition.

*******************************************************************************/

extern zlStatusE zl5011xMmSetParityErrorThreshold(zl5011xParamsS *zl5011xParams,
      Uint32T extMemParityTripPoint)
{
   Uint8T pExtMemParityCount;
   zl5011xBooleanE pExtMemParityFailed;
   zlStatusE status = ZL5011X_OK;

   ZL5011X_TRACE(ZL5011X_MM_FN_ID, "zl5011xMmSetParityErrorThreshold: 0x%08x ",
               extMemParityTripPoint, 0, 0, 0, 0, 0);

   if (extMemParityTripPoint > ZL5011X_EMEMPARITY2_LIMIT)
   {
      extMemParityTripPoint = ZL5011X_EMEMPARITY2_LIMIT;
   }

   status = zl5011xWrite(zl5011xParams, ZL5011X_MM_EMEMPARITY2, extMemParityTripPoint);
   zl5011xParams->packetMemory.extMemParityTripPoint = extMemParityTripPoint;

   if (status == ZL5011X_OK)
   {
      /* force the parity count to 0 by reading the register */
      status = zl5011xMmGetParityStatus(zl5011xParams, &pExtMemParityCount,
            &pExtMemParityFailed);
   }

   return(status);
}

/*******************************************************************************

 Function:
    zl5011xMmGetParityStatus

 Description:
   This function gets the count of parity failures from the EMEMPTYCNT register,
   which also contains a boolean indicator of parity fail.

 Inputs:
    zl5011xParams      Pointer to the structure for this device instance

 Outputs:
    pExtMemParityCount  count of parity fails.
    pExtMemParityFailed indicates a failure has occurred.

 Returns:
   zlStatusE

 Remarks:

*******************************************************************************/

extern zlStatusE zl5011xMmGetParityStatus(zl5011xParamsS  *zl5011xParams, Uint8T *pExtMemParityCount,
                                  zl5011xBooleanE *pExtMemParityFailed)
{
   zlStatusE status = ZL5011X_OK;
   Uint32T readValue;

   status = zl5011xRead(zl5011xParams, ZL5011X_MM_EMEMPTYCNT, &readValue);
   if (status == ZL5011X_OK)
   {
      if ((readValue & ZL5011X_1BIT_MASK)== 0)
      {
         *pExtMemParityFailed = ZL5011X_FALSE;
      }
      else
      {
         *pExtMemParityFailed = ZL5011X_TRUE;
         *pExtMemParityCount = (Uint8T)((readValue >> ZL5011X_MM_PARITY_FAIL_COUNT_LSB)& ZL5011X_4BIT_MASK);
      }
   }
   ZL5011X_TRACE(ZL5011X_MM_FN_ID, "zl5011xMmGetParityStatus: Parity count %2d"
                         "Parity fail %d (1=FAIL, 0= OK)",
                         *pExtMemParityCount, *pExtMemParityFailed, 0, 0, 0, 0);
   return(status);
}

/*******************************************************************************

 Function: