serialbuf.bas

82 sample programs written in BASCOM-8051 for 8051 developement

'------------------------------------------------------
'                 SERIALBUF.BAS
'             (c) 2001 MCS Electronics
' This program shows how to implement a serial input
' buffer
'------------------------------------------------------


'we use conditional compilation for the optional spi int
Const Spi = 1

'first we tell the compiler about our routines
$serialoutput = Sendchar
$serialinput = Recchar

'now we need some variables to store the input and some pointers
'buf() is an array that holds the data
'wpos is a pointer that points to the last position written
'rpos is a pointer that points to the last read position
'rcount is a byte that stores the number of bytes waiting in the buffer
Dim Buf(10) As Iram Byte , Wpos As Iram Byte , Rpos As Iram Byte , Rcount As Iram Byte

'now we specify the ISR
On Serial Isr_ser Nosave
'we must enable it
Enable Serial
'and enable the global interrupt bit
Enable Interrupts

'since by default the compiler will generate mov scon,#82 to enable TI,
'we override it so TI is not enabled
mov scon,#80


'This is our actual program
'we need a byte to store a value
Dim A As Byte
'we print some text to show that we can print
Print "Hello"
Print "world"
'here we ask for the number
Do
  Input "Number " , A
  'here we print the entered number
  Print A
Loop Until A = 0
End


'we use some asm
$asm
Sendchar:

' we could disable the serial interrupts here but it would mean
' that no receive interrupt could occur too

 Mov sbuf, a                                                                     ; write the data
 Jnb scon.1, *+0                                                                       ; wait until it is ready
 Clr scon.1
                                                             ; Disable Ti
Ret

' That Was Easy


Recchar:
  mov a,{rcount}                                              ; get the number of bytes waiting in the buffer
  jz recchar                                                  ; when zero try again
  push h'00                                                   ; now we must save the used registers
  push psw

  mov r0,#{buf}                                               ; load the address of the buffer
  mov a,{rpos}                                                              ; load the last read position
  add a,r0                                                    ; add it
  mov r0,a                                                    ; put back in r0
  mov a,@r0                                                   ; get it out of the buffer
  inc {rpos}                                                  ; increase the read pointer
  dec {rcount}                                                ; 1 char less waiting
  push acc                                                    ; save the byte we retrieved from the buffer
  mov a,{rpos}                                                                     ; get the read pos
  cjne a,#10, recchar_exit                                    ; is it past the size of the buffer
  mov {rpos},#0                                               ; reset it to the begin
Recchar_exit:
  pop acc                                                     ; restore byte
  pop psw                                                     ; restore registers
  pop h'00
ret                                                           ; return

$end Asm


'this is the ISR that gets fired when TI or RI gets set
Isr_ser:
 push acc
 push h'00                                                    ; save used registers
 push psw
 jnb scon.0, .isr_tx                                          ; was RI causing the interrupt?
 mov a,{wpos}                                                               ; get write position
 mov r0,#{buf}                                                ; load address of buffer
 add a,r0                                                     ; add it
 mov r0,a                                                     ; back to r0
 mov @r0,sbuf                                                 ; store the char in the buffer
 inc {wpos}                                                   ; increase write pointer
 inc {rcount}                                                 ; and we have one char more waiting
 clr scon.0                                                   ; clear RI
 mov a ,{wpos}                                                ;get the write pointer
 cjne a,#10,.isr_exit                                         ;is it past the size?
 Mov {wpos},#0                                                ; reset it
 sjmp .isr_exit                                               ;exit
Isr_tx:
' TI Caused The Int But It Gets Reset In The Sendchar Routine

'optional for the 8252 that has a shared SPI interrupt you can add the following code
#if Spi
  mov a,spsr                                                  ; get status register
  jnb acc.7, .isr_exit                                        ; it was not the SPI that caused the int
  mov spsr,#255                                               ; to clear the int flag spif and wcol must be set
  mov a,spdr                                                  ; by reading the data register the int gets cleared
  'now we can store the data this is not implemented
  'note that acc gets popped so acc will be destroyed

#endif


Isr_exit:
 pop psw                                                      ; restore regs
 pop h'00
 pop acc
Return