avr_sd_src.c

基于avr单片机的读写sd卡的c源程序

SD卡接口程序/******************************************/
/*           SD Code for   M32L             */
/*       By   pasyong        */
/*       2006-4         */
/*       Base ICC6.31A             */
/************************************************************/
#include <iom32v.h>
#include <macros.h>
#include "1011.h"
#define uchar unsigned char
#define uint unsigned int
#define MMC_CS_PIN     BIT(4)    //PORTB.4
#define MMC_PORT       PORTB????uchar reading=0,a=0,pointer=0;
void sd_port_init()
{
MMC_PORT =MMC_CS_PIN;
}
uchar BUFFER[512];                   //扇区缓冲区
uint i=0;
void delay_nus(uint n)
?{
?unsigned char  b;
  for (b = 1; b<n; b++)
   ;
?}
//****************************************************************************
//Send a Command to MMC/SD-Card
//Return: the second byte of response register of MMC/SD-Card
//****************************************************************************
uchar SD_Write_Command(uchar cmd,unsigned long arg)
{
   uchar tmp;
   uchar retry=0;
??
   //MMC_PORT =MMC_CS_PIN;       //SD卡关闭??
   //send 8 Clock Impulse
   Write_Byte_SPI(0xFF);
??
   //set MMC_Chip_Select to low (MMC/SD-Card active)
  MMC_PORT&=~MMC_CS_PIN;       //SD卡使能   Write_Byte_SPI(cmd 0x40);   //送头命令
   Write_Byte_SPI(arg>>24);
   Write_Byte_SPI(arg>>16);     //send 6 Byte Command to MMC/SD-Card
   Write_Byte_SPI(arg>>8);
   Write_Byte_SPI(arg&0xff);
   Write_Byte_SPI(0x95);       //仅仅对RESET有效的CRC效验码
?
   //get 8 bit response
   //Read_Byte_MMC(); //read the first byte,ignore it.
   do
   {  //Only last 8 bit is used here.Read it out.
      tmp = Read_Byte_SPI();
      retry++;
   }
   while((tmp==0xff)&&(retry<100));  //当没有收到有效的命令的时候
??
   if(reading==0)
   MMC_PORT =MMC_CS_PIN;            //MMC_CS_PIN=1;
   else MMC_PORT&=~MMC_CS_PIN;      //MMC_CS_PIN=0;??
   return(tmp);
}
//****************************************************************************
//SD卡初始化(SPI-MODE)
//****************************************************************************
uchar SD_Init(void)
{?
   uchar retry,temp;
   uchar i;
   MMC_PORT&=~MMC_CS_PIN;      //SD卡使能
?
  delay_nus(250);  //Wait MMC/SD ready...
   for (i=0;i<0x0f;i++)
   {
      Write_Byte_SPI(0xff); //send 74 clock at least!!!
   }
   //Send Command CMD0 to MMC/SD Card
   retry=0;
??
   do
   { //retry 200 times to send CMD0 command
     temp=SD_Write_Command(0,0);
     retry++;
     if(retry==100)
     {
      ;//CMD0 Error!
     }
   }
   while(temp!=1);?
??
   //Send Command CMD1 to MMC/SD-Card
   retry=0;
   do
   { //retry 100 times to send CMD1 command
     temp=SD_Write_Command(1,0);
     retry++;
     if(retry==100)
     {
     ;
     }
   }
   while(temp!=0);
   retry=0;
    SD_Write_Command(16,512);     //设置一次读写BLOCK的长度为512个字节
?
   MMC_PORT =MMC_CS_PIN;   //MMC_CS_PIN=1;  //set MMC_Chip_Select to high
   return(0); //All commands have been taken.
}
//****************************************************************************
//从SD卡读一个扇区  Return 0 if no Error.
//****************************************************************************
uchar SD_Read_Block(unsigned long address)
{?
   uchar temp=0;uint i=0;
   reading=1;
   temp=SD_Write_Command(17,address);     //读出RESPONSE????
   while (Read_Byte_SPI()!= 0xfe)
   {;}  //直到读取到了数据的开始头0XFE,才继续
   for(i=0; i<512; i++)
?{
?BUFFER[i]=Read_Byte_SPI();
?}
   Read_Byte_SPI();//CRC - Byte
   Read_Byte_SPI();//CRC - Byte
   reading=0;
   MMC_PORT =MMC_CS_PIN;        //关闭SD卡
   return(temp);
}