extflashm.nc

无线通信的主要编程软件,是无线通信工作人员的必备工具,关天相关教程我会在后续传上.

// $Id: ExtFlashM.nc,v 1.1 2005/07/22 17:40:10 jwhui Exp $

/*									tab:2
 * "Copyright (c) 2000-2005 The Regents of the University  of California.  
 * All rights reserved.
 *
 * Permission to use, copy, modify, and distribute this software and its
 * documentation for any purpose, without fee, and without written agreement is
 * hereby granted, provided that the above copyright notice, the following
 * two paragraphs and the author appear in all copies of this software.
 * 
 * IN NO EVENT SHALL THE UNIVERSITY OF CALIFORNIA BE LIABLE TO ANY PARTY FOR
 * DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT
 * OF THE USE OF THIS SOFTWARE AND ITS DOCUMENTATION, EVEN IF THE UNIVERSITY OF
 * CALIFORNIA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * 
 * THE UNIVERSITY OF CALIFORNIA SPECIFICALLY DISCLAIMS ANY WARRANTIES,
 * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
 * AND FITNESS FOR A PARTICULAR PURPOSE.  THE SOFTWARE PROVIDED HEREUNDER IS
 * ON AN "AS IS" BASIS, AND THE UNIVERSITY OF CALIFORNIA HAS NO OBLIGATION TO
 * PROVIDE MAINTENANCE, SUPPORT, UPDATES, ENHANCEMENTS, OR MODIFICATIONS."
 */

/**
 * @author Jonathan Hui <[e-mail]>
 */

module ExtFlashM {
  provides {
    interface StdControl;
    interface ExtFlash;
  }
  uses {
    interface HPLUSARTControl as USARTControl;
  }
}

implementation {

  command result_t StdControl.init() {
    TOSH_MAKE_FLASH_HOLD_OUTPUT();
    TOSH_MAKE_FLASH_CS_OUTPUT();
    TOSH_SET_FLASH_HOLD_PIN();
    call USARTControl.setModeSPI();
    return SUCCESS;
  }

  command result_t StdControl.start() { 
    return SUCCESS; 
  }

  command result_t StdControl.stop() { 

    TOSH_CLR_FLASH_CS_PIN();
    
    call USARTControl.tx(0xb9);
    while(!(call USARTControl.isTxEmpty()));

    TOSH_SET_FLASH_CS_PIN();

    call USARTControl.disableSPI();

    return SUCCESS; 

  }

  void powerOnFlash() {

    uint8_t i;

    TOSH_CLR_FLASH_CS_PIN();

    // command byte + 3 dummy bytes + signature
    for ( i = 0; i < 5; i++ ) {
      call USARTControl.tx(0xab);
      while(!(call USARTControl.isTxIntrPending()));
    }
    
    TOSH_SET_FLASH_CS_PIN();

  }

  command void ExtFlash.startRead(uint32_t addr) {

    uint8_t i;
    
    powerOnFlash();
    
    TOSH_CLR_FLASH_CS_PIN();
    
    // add command byte to address
    addr |= (uint32_t)0x3 << 24;

    // address
    for ( i = 4; i > 0; i-- ) {
      call USARTControl.tx((addr >> (i-1)*8) & 0xff);
      while(!(call USARTControl.isTxIntrPending()));
    }    

  }

  command uint8_t ExtFlash.readByte() {
    call USARTControl.rx();
    call USARTControl.tx(0);
    while(!(call USARTControl.isRxIntrPending()));
    return call USARTControl.rx();
  }

  command void ExtFlash.stopRead() {
    TOSH_SET_FLASH_CS_PIN();
  }

}