2.6.18-rc4-at91.patch.gz

内容包括2.6.14内核到2.6.23内核的at91内核补丁（没有2.6.19的）

+		at91_set_B_periph(AT91_PIN_PB17, 0);	/* ERXDV */
+		at91_set_B_periph(AT91_PIN_PB16, 0);	/* ERX3 */
+		at91_set_B_periph(AT91_PIN_PB15, 0);	/* ERX2 */
+		at91_set_B_periph(AT91_PIN_PB14, 0);	/* ETXER */
+		at91_set_B_periph(AT91_PIN_PB13, 0);	/* ETX3 */
+		at91_set_B_periph(AT91_PIN_PB12, 0);	/* ETX2 */
+	}
+
+	eth_data = *data;
+	platform_device_register(&at91rm9200_eth_device);
+}
+#else
+void __init at91_add_device_eth(struct at91_eth_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Compact Flash / PCMCIA
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
+static struct at91_cf_data cf_data;
+
+#define AT91_CF_BASE	AT91_CHIPSELECT_4
+
+static struct resource at91_cf_resources[] = {
+	[0] = {
+		.start	= AT91_CF_BASE,
+		/* ties up CS4, CS5 and CS6 */
+		.end	= AT91_CF_BASE + (0x30000000 - 1),
+		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+	},
+};
+
+static struct platform_device at91rm9200_cf_device = {
+	.name		= "at91_cf",
+	.id		= -1,
+	.dev		= {
+				.platform_data		= &cf_data,
+	},
+	.resource	= at91_cf_resources,
+	.num_resources	= ARRAY_SIZE(at91_cf_resources),
+};
+
+void __init at91_add_device_cf(struct at91_cf_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->irq_pin) {
+		at91_set_gpio_input(data->irq_pin, 1);
+		at91_set_deglitch(data->irq_pin, 1);
+	}
+	at91_set_gpio_input(data->det_pin, 1);
+	at91_set_deglitch(data->det_pin, 1);
+
+	/* outputs, initially off */
+	if (data->vcc_pin)
+		at91_set_gpio_output(data->vcc_pin, 0);
+	at91_set_gpio_output(data->rst_pin, 0);
+
+	/* force poweron defaults for these pins ... */
+	at91_set_A_periph(AT91_PIN_PC9, 0);	/* A25/CFRNW */
+	at91_set_A_periph(AT91_PIN_PC10, 0);	/* NCS4/CFCS */
+	at91_set_A_periph(AT91_PIN_PC11, 0);	/* NCS5/CFCE1 */
+	at91_set_A_periph(AT91_PIN_PC12, 0);	/* NCS6/CFCE2 */
+
+	cf_data = *data;
+	platform_device_register(&at91rm9200_cf_device);
+}
+#else
+void __init at91_add_device_cf(struct at91_cf_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  MMC / SD
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MMC_AT91RM9200) || defined(CONFIG_MMC_AT91RM9200_MODULE)
+static u64 mmc_dmamask = 0xffffffffUL;
+static struct at91_mmc_data mmc_data;
+
+static struct resource at91_mmc_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_MCI,
+		.end	= AT91RM9200_BASE_MCI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_MCI,
+		.end	= AT91RM9200_ID_MCI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_mmc_device = {
+	.name		= "at91_mci",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &mmc_dmamask,
+				.coherent_dma_mask	= 0xffffffff,
+				.platform_data		= &mmc_data,
+	},
+	.resource	= at91_mmc_resources,
+	.num_resources	= ARRAY_SIZE(at91_mmc_resources),
+};
+
+void __init at91_add_device_mmc(struct at91_mmc_data *data)
+{
+	if (!data)
+		return;
+
+	/* input/irq */
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+	if (data->wp_pin)
+		at91_set_gpio_input(data->wp_pin, 1);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA27, 0);
+
+	if (data->is_b) {
+		/* CMD */
+		at91_set_B_periph(AT91_PIN_PA8, 0);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_B_periph(AT91_PIN_PA9, 0);
+		if (data->wire4) {
+			at91_set_B_periph(AT91_PIN_PA10, 0);
+			at91_set_B_periph(AT91_PIN_PA11, 0);
+			at91_set_B_periph(AT91_PIN_PA12, 0);
+		}
+	} else {
+		/* CMD */
+		at91_set_A_periph(AT91_PIN_PA28, 0);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_A_periph(AT91_PIN_PA29, 0);
+		if (data->wire4) {
+			at91_set_B_periph(AT91_PIN_PB3, 0);
+			at91_set_B_periph(AT91_PIN_PB4, 0);
+			at91_set_B_periph(AT91_PIN_PB5, 0);
+		}
+	}
+
+	mmc_data = *data;
+	platform_device_register(&at91rm9200_mmc_device);
+}
+#else
+void __init at91_add_device_mmc(struct at91_mmc_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+static struct at91_nand_data nand_data;
+
+#define AT91_SMARTMEDIA_BASE	AT91_CHIPSELECT_3
+
+static struct resource at91_nand_resources[] = {
+	{
+		.start	= AT91_SMARTMEDIA_BASE,
+		.end	= AT91_SMARTMEDIA_BASE + SZ_8M - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91_nand_device = {
+	.name		= "at91_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= at91_nand_resources,
+	.num_resources	= ARRAY_SIZE(at91_nand_resources),
+};
+
+void __init at91_add_device_nand(struct at91_nand_data *data)
+{
+	if (!data)
+		return;
+
+	/* enable pin */
+	if (data->enable_pin)
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (data->rdy_pin)
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (data->det_pin)
+		at91_set_gpio_input(data->det_pin, 1);
+
+	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */
+	at91_set_A_periph(AT91_PIN_PC3, 0);		/* SMWE */
+
+	nand_data = *data;
+	platform_device_register(&at91_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct at91_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+
+static struct resource at91_twi_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_TWI,
+		.end	= AT91RM9200_BASE_TWI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_TWI,
+		.end	= AT91RM9200_ID_TWI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_twi_device = {
+	.name		= "at91_i2c",
+	.id		= -1,
+	.resource	= at91_twi_resources,
+	.num_resources	= ARRAY_SIZE(at91_twi_resources),
+};
+
+void __init at91_add_device_i2c(void)
+{
+	/* pins used for TWI interface */
+	at91_set_A_periph(AT91_PIN_PA25, 0);		/* TWD */
+	at91_set_multi_drive(AT91_PIN_PA25, 1);
+
+	at91_set_A_periph(AT91_PIN_PA26, 0);		/* TWCK */
+	at91_set_multi_drive(AT91_PIN_PA26, 1);
+
+	platform_device_register(&at91rm9200_twi_device);
+}
+#else
+void __init at91_add_device_i2c(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
+static u64 spi_dmamask = 0xffffffffUL;
+
+static struct resource at91_spi_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_SPI,
+		.end	= AT91RM9200_BASE_SPI + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_SPI,
+		.end	= AT91RM9200_ID_SPI,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91rm9200_spi_device = {
+	.name		= "at91_spi",
+	.id		= 0,
+	.dev		= {
+		.dma_mask		= &spi_dmamask,
+		.coherent_dma_mask	= 0xffffffff,
+	},
+	.resource	= at91_spi_resources,
+	.num_resources	= ARRAY_SIZE(at91_spi_resources),
+};
+
+static const unsigned at91_spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+	int i;
+	unsigned long cs_pin;
+
+	at91_set_A_periph(AT91_PIN_PA0, 0);	/* MISO */
+	at91_set_A_periph(AT91_PIN_PA1, 0);	/* MOSI */
+	at91_set_A_periph(AT91_PIN_PA2, 0);	/* SPCK */
+
+	/* Enable SPI chip-selects */
+	for (i = 0; i < nr_devices; i++) {
+		if (devices[i].controller_data)
+			cs_pin = (unsigned long) devices[i].controller_data;
+		else
+			cs_pin = at91_spi_standard_cs[devices[i].chip_select];
+
+#ifdef CONFIG_SPI_AT91_MANUAL_CS
+		at91_set_gpio_output(cs_pin, 1);
+#else
+		at91_set_A_periph(cs_pin, 0);
+#endif
+
+		/* pass chip-select pin to driver */
+		devices[i].controller_data = (void *) cs_pin;
+	}
+
+	spi_register_board_info(devices, nr_devices);
+	at91_clock_associate("spi_clk", &at91rm9200_spi_device.dev, "spi");
+	platform_device_register(&at91rm9200_spi_device);
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  RTC
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_RTC_DRV_AT91) || defined(CONFIG_RTC_DRV_AT91_MODULE)
+static struct platform_device at91rm9200_rtc_device = {
+	.name		= "at91_rtc",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_rtc(void)
+{
+	platform_device_register(&at91rm9200_rtc_device);
+}
+#else
+static void __init at91_add_device_rtc(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  Watchdog
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91_WATCHDOG) || defined(CONFIG_AT91_WATCHDOG_MODULE)
+static struct platform_device at91rm9200_wdt_device = {
+	.name		= "at91_wdt",
+	.id		= -1,
+	.num_resources	= 0,
+};
+
+static void __init at91_add_device_watchdog(void)
+{
+	platform_device_register(&at91rm9200_wdt_device);
+}
+#else
+static void __init at91_add_device_watchdog(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  LEDs
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_LEDS)
+u8 at91_leds_cpu;
+u8 at91_leds_timer;
+
+void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+{
+	at91_leds_cpu	= cpu_led;
+	at91_leds_timer	= timer_led;
+}
+#else
+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_AT91)
+static struct resource dbgu_resources[] = {
+	[0] = {
+		.start	= AT91_VA_BASE_SYS + AT91_DBGU,
+		.end	= AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_SYS,
+		.end	= AT91RM9200_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct at91_uart_data dbgu_data = {
+	.use_dma_tx	= 0,
+	.use_dma_rx	= 0,		/* DBGU not capable of receive DMA */
+};
+
+static struct platform_device at91rm9200_dbgu_device = {
+	.name		= "at91_usart",
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &dbgu_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= dbgu_resources,
+	.num_resources	= ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA30, 0);		/* DRXD */
+	at91_set_A_periph(AT91_PIN_PA31, 1);		/* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US0,
+		.end	= AT91RM9200_BASE_US0 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US0,
+		.end	= AT91RM9200_ID_US0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct at91_uart_data uart0_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart0_device = {
+	.name		= "at91_usart",
+	.id		= 1,
+	.dev		= {
+				.platform_data	= &uart0_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart0_resources,
+	.num_resources	= ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PA17, 1);		/* TXD0 */
+	at91_set_A_periph(AT91_PIN_PA18, 0);		/* RXD0 */
+	at91_set_A_periph(AT91_PIN_PA20, 0);		/* CTS0 */
+
+	/*
+	 * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
+	 *  We need to drive the pin manually.  Default is off (RTS is active low).
+	 */
+	at91_set_gpio_output(AT91_PIN_PA21, 1);
+}
+
+static struct resource uart1_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US1,
+		.end	= AT91RM9200_BASE_US1 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US1,
+		.end	= AT91RM9200_ID_US1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct at91_uart_data uart1_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart1_device = {
+	.name		= "at91_usart",
+	.id		= 2,
+	.dev		= {
+				.platform_data	= &uart1_data,
+				.coherent_dma_mask = 0xffffffff,
+	},
+	.resource	= uart1_resources,
+	.num_resources	= ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(void)
+{
+	at91_set_A_periph(AT91_PIN_PB18, 0);		/* RI1 */
+	at91_set_A_periph(AT91_PIN_PB19, 0);		/* DTR1 */
+	at91_set_A_periph(AT91_PIN_PB20, 1);		/* TXD1 */
+	at91_set_A_periph(AT91_PIN_PB21, 0);		/* RXD1 */
+	at91_set_A_periph(AT91_PIN_PB23, 0);		/* DCD1 */
+	at91_set_A_periph(AT91_PIN_PB24, 0);		/* CTS1 */
+	at91_set_A_periph(AT91_PIN_PB25, 0);		/* DSR1 */
+	at91_set_A_periph(AT91_PIN_PB26, 0);		/* RTS1 */
+}
+
+static struct resource uart2_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_US2,
+		.end	= AT91RM9200_BASE_US2 + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91RM9200_ID_US2,
+		.end	= AT91RM9200_ID_US2,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct at91_uart_data uart2_data = {
+	.use_dma_tx	= 1,
+	.use_dma_rx	= 1,
+};
+
+static struct platform_device at91rm9200_uart2_device = {
+	.name		= "at91_usart",
+	.id		= 3,