📄 stm32f10x_usart.lst
字号:
184
185 /* Configure the USART HFC -------------------------------------------------*/
186 /* Set CTSE and RTSE bits according to USART_HardwareFlowControl value */
187 tmpreg |= USART_InitStruct->USART_HardwareFlowControl;
188
189 /* Write to USART CR3 */
190 USARTx->CR3 = (u16)tmpreg;
191
192 /*---------------------------- USART BRR Configuration -----------------------*/
193 tmpreg = 0x00;
194
195 /* Configure the USART Baud Rate -------------------------------------------*/
196 RCC_GetClocksFreq(&RCC_ClocksStatus);
197 if ((*(u32*)&USARTx) == USART1_BASE)
198 {
199 apbclock = RCC_ClocksStatus.PCLK2_Frequency;
200 }
201 else
202 {
203 apbclock = RCC_ClocksStatus.PCLK1_Frequency;
204 }
205
206 /* Determine the integer part */
207 integerdivider = ((0x19 * apbclock) / (0x04 * (USART_InitStruct->USART_BaudRate)));
208 tmpreg = (integerdivider / 0x64) << 0x04;
209
210 /* Determine the fractional part */
211 fractionaldivider = integerdivider - (0x64 * (tmpreg >> 0x04));
212 tmpreg |= ((((fractionaldivider * 0x10) + 0x32) / 0x64)) & ((u8)0x0F);
213
214 /* Write to USART BRR */
215 USARTx->BRR = (u16)tmpreg;
216 }
217
218 /*******************************************************************************
219 * Function Name : USART_StructInit
220 * Description : Fills each USART_InitStruct member with its default value.
221 * Input : - USART_InitStruct: pointer to a USART_InitTypeDef structure
222 * which will be initialized.
223 * Output : None
224 * Return : None
225 *******************************************************************************/
226 void USART_StructInit(USART_InitTypeDef* USART_InitStruct)
227 {
228 /* USART_InitStruct members default value */
229 USART_InitStruct->USART_BaudRate = 0x2580; /* 9600 Baud */
230 USART_InitStruct->USART_WordLength = USART_WordLength_8b;
231 USART_InitStruct->USART_StopBits = USART_StopBits_1;
232 USART_InitStruct->USART_Parity = USART_Parity_No ;
233 USART_InitStruct->USART_HardwareFlowControl = USART_HardwareFlowControl_None;
234 USART_InitStruct->USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
235 USART_InitStruct->USART_Clock = USART_Clock_Disable;
236 USART_InitStruct->USART_CPOL = USART_CPOL_Low;
237 USART_InitStruct->USART_CPHA = USART_CPHA_1Edge;
238 USART_InitStruct->USART_LastBit = USART_LastBit_Disable;
239 }
240
241 /*******************************************************************************
242 * Function Name : USART_Cmd
243 * Description : Enables or disables the specified USART peripheral.
244 * Input : - USARTx: where x can be 1, 2 or 3 to select the USART
245 * peripheral.
246 * : - NewState: new state of the USARTx peripheral.
247 * This parameter can be: ENABLE or DISABLE.
248 * Output : None
249 * Return : None
250 *******************************************************************************/
251 void USART_Cmd(USART_TypeDef* USARTx, FunctionalState NewState)
252 {
253 /* Check the parameters */
254 assert(IS_FUNCTIONAL_STATE(NewState));
255
256 if (NewState != DISABLE)
257 {
258 /* Enable the selected USART by setting the RUN bit in the CR1 register */
259 USARTx->CR1 |= CR1_RUN_Set;
260 }
261 else
262 {
263 /* Disable the selected USART by clearing the RUN bit in the CR1 register */
264 USARTx->CR1 &= CR1_RUN_Reset;
265 }
266 }
267
268 /*******************************************************************************
269 * Function Name : USART_ITConfig
270 * Description : Enables or disables the specified USART interrupts.
271 * Input : - USARTx: where x can be 1, 2 or 3 to select the USART
272 * peripheral.
273 * - USART_IT: specifies the USART interrupt sources to be
274 * enabled or disabled.
275 * This parameter can be one of the following values:
276 * - USART_IT_PE
277 * - USART_IT_TXE
278 * - USART_IT_TC
279 * - USART_IT_RXNE
280 * - USART_IT_IDLE
281 * - USART_IT_LBD
282 * - USART_IT_CTS
283 * - USART_IT_ERR
284 * - NewState: new state of the specified USARTx interrupts.
285 * This parameter can be: ENABLE or DISABLE.
286 * Output : None
287 * Return : None
288 *******************************************************************************/
289 void USART_ITConfig(USART_TypeDef* USARTx, u16 USART_IT, FunctionalState NewState)
290 {
291 u32 usartreg = 0x00, itpos = 0x00, itmask = 0x00;
292 u32 address = 0x00;
293
294 /* Check the parameters */
295 assert(IS_USART_CONFIG_IT(USART_IT));
296 assert(IS_FUNCTIONAL_STATE(NewState));
297
298 /* Get the USART register index */
299 usartreg = (((u8)USART_IT) >> 0x05);
300
301 /* Get the interrupt position */
302 itpos = USART_IT & USART_IT_Mask;
303
304 itmask = (((u32)0x01) << itpos);
305 address = *(u32*)&(USARTx);
306
307 if (usartreg == 0x01) /* The IT is in CR1 register */
308 {
309 address += 0x0C;
310 }
311 else if (usartreg == 0x02) /* The IT is in CR2 register */
312 {
313 address += 0x10;
314 }
315 else /* The IT is in CR3 register */
316 {
317 address += 0x14;
318 }
319 if (NewState != DISABLE)
320 {
321 *(u32*)address |= itmask;
322 }
323 else
324 {
325 *(u32*)address &= ~itmask;
326 }
327 }
328
329 /*******************************************************************************
330 * Function Name : USART_DMACmd
331 * Description : Enables or disables the USART抯 DMA interface.
332 * Input : - USARTx: where x can be 1, 2 or 3 to select the USART
333 * peripheral.
334 * - USART_DMAReq: specifies the DMA request.
335 * This parameter can be any combination of the following values:
336 * - USART_DMAReq_Tx
337 * - USART_DMAReq_Rx
338 * - NewState: new state of the DMA Request sources.
339 * This parameter can be: ENABLE or DISABLE.
340 * Output : None
341 * Return : None
342 *******************************************************************************/
343 void USART_DMACmd(USART_TypeDef* USARTx, u16 USART_DMAReq, FunctionalState NewState)
344 {
345 /* Check the parameters */
346 assert(IS_USART_DMAREQ(USART_DMAReq));
347 assert(IS_FUNCTIONAL_STATE(NewState));
348
349 if (NewState != DISABLE)
350 {
351 /* Enable the DMA transfer for selected requests by setting the DMAT and/or
352 DMAR bits in the USART CR3 register */
353 USARTx->CR3 |= USART_DMAReq;
354 }
355 else
356 {
357 /* Disable the DMA transfer for selected requests by clearing the DMAT and/or
358 DMAR bits in the USART CR3 register */
359 USARTx->CR3 &= (u16)~USART_DMAReq;
360 }
361 }
362
363 /*******************************************************************************
364 * Function Name : USART_SetAddress
365 * Description : Sets the address of the USART node.
366 * Input : - USARTx: where x can be 1, 2 or 3 to select the USART
367 * peripheral.
368 * - USART_Address: Indicates the address of the USART node.
369 * Output : None
370 * Return : None
371 *******************************************************************************/
372 void USART_SetAddress(USART_TypeDef* USARTx, u8 USART_Address)
373 {
374 /* Check the parameters */
375 assert(IS_USART_ADDRESS(USART_Address));
376
377 /* Clear the USART address */
378 USARTx->CR2 &= CR2_Address_Mask;
379 /* Set the USART address node */
380 USARTx->CR2 |= USART_Address;
381 }
382
383 /*******************************************************************************
384 * Function Name : USART_WakeUpConfig
385 * Description : Selects the USART WakeUp method.
386 * Input : - USARTx: where x can be 1, 2 or 3 to select the USART
387 * peripheral.
388 * - USART_WakeUp: specifies the USART wakeup method.
389 * This parameter can be one of the following values:
390 * - USART_WakeUp_IdleLine
391 * - USART_WakeUp_AddressMark
392 * Output : None
393 * Return : None
394 *******************************************************************************/
395 void USART_WakeUpConfig(USART_TypeDef* USARTx, u16 USART_WakeUp)
396 {
397 /* Check the parameters */
398 assert(IS_USART_WAKEUP(USART_WakeUp));
399
400 USARTx->CR1 &= CR3_WAKE_Mask;
401 USARTx->CR1 |= USART_WakeUp;
402 }
403
404 /*******************************************************************************
405 * Function Name : USART_ReceiverWakeUpCmd
406 * Description : Determines if the USART is in mute mode or not.
407 * Input : - USARTx: where x can be 1, 2 or 3 to select the USART
408 * peripheral.
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -