main.c

CH452芯片使用（键盘及数码管显示）法国海军考虑：回家看

#include"CH452CMD.H"
#include"c8051F020.h"
#include"PIN.H"
#include"intrins.h"
#include"math.h"




// Peripheral specific initialization functions,
// Called from the Init_Device() function
void Reset_Sources_Init()
{
    WDTCN     = 0xDE;
    WDTCN     = 0xAD;
}

void Port_IO_Init()
{
    // P0.0  -  Unassigned,  Open-Drain, Digital
    // P0.1  -  Unassigned,  Open-Drain, Digital
    // P0.2  -  Unassigned,  Open-Drain, Digital
    // P0.3  -  Unassigned,  Open-Drain, Digital
    // P0.4  -  Unassigned,  Open-Drain, Digital
    // P0.5  -  Unassigned,  Open-Drain, Digital
    // P0.6  -  Unassigned,  Open-Drain, Digital
    // P0.7  -  Unassigned,  Open-Drain, Digital

    // P1.0  -  Unassigned,  Open-Drain, Digital
    // P1.1  -  Unassigned,  Open-Drain, Digital
    // P1.2  -  Unassigned,  Open-Drain, Digital
    // P1.3  -  Unassigned,  Open-Drain, Digital
    // P1.4  -  Unassigned,  Open-Drain, Digital
    // P1.5  -  Unassigned,  Open-Drain, Digital
    // P1.6  -  Unassigned,  Open-Drain, Digital
    // P1.7  -  Unassigned,  Open-Drain, Digital

    // P2.0  -  Unassigned,  Open-Drain, Digital
    // P2.1  -  Unassigned,  Open-Drain, Digital
    // P2.2  -  Unassigned,  Open-Drain, Digital
    // P2.3  -  Unassigned,  Open-Drain, Digital
    // P2.4  -  Unassigned,  Open-Drain, Digital
    // P2.5  -  Unassigned,  Open-Drain, Digital
    // P2.6  -  Unassigned,  Open-Drain, Digital
    // P2.7  -  Unassigned,  Open-Drain, Digital

    // P3.0  -  Unassigned,  Open-Drain, Digital
    // P3.1  -  Unassigned,  Open-Drain, Digital
    // P3.2  -  Unassigned,  Open-Drain, Digital
    // P3.3  -  Unassigned,  Open-Drain, Digital
    // P3.4  -  Unassigned,  Open-Drain, Digital
    // P3.5  -  Unassigned,  Open-Drain, Digital
    // P3.6  -  Unassigned,  Open-Drain, Digital
    // P3.7  -  Unassigned,  Open-Drain, Digital

    XBR2      = 0xC0;
}

// Initialization function for device,
// Call Init_Device() from your main program
void Init_Device(void)
{
    Reset_Sources_Init();
    Port_IO_Init();
}


void main(void)
  {	
  EA=0;
   Init_Device();
  EA=1;
 //  CH452_Write(CH452_RESET);	
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	CH452_Write(CH452_SYSON2);//打开键盘显示
	CH452_Write(CH452_BCD);   // BCD译码,8个数码管
CH452_Write(0x601);       //设置数码管0爽书    
while(1)
{
  
  CH452_Write(CH452_DIG0|0);
    DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
}
}

void CH452_Write(unsigned short cmd)
{
	unsigned char i;
	DISABLE_KEY_INTERRUPT;		  //禁止键盘中断,防止传输过程中被CH452中断而进入中断服务程序中再次传输
	CH452_LOAD_CLR;                 //命令开始,LOAD=0
	CH452_LOAD_D_OUT;		// 设置LOAD为输出方向
	CH452_DOUT_D_IN;		// 设置DOUT为输入方向
	CH452_DIN_D_OUT;		// 设置DIN为输出方向
	CH452_DCLK_D_OUT;		// 设置DCLK为输出方向
	for(i=0;i!=12;i++)				//送入12位数据，低位在前
	{
	 if (cmd&1) {CH452_DIN_SET;}
	    else {CH452_DIN_CLR;}  // 输出位数据
                                   // 另外的表达CH452_DIN=cmd&1;
    	 CH452_DCLK_CLR;
    	 cmd>>=1;
	 DELAY_1US;
	 DELAY_1US;	
	    	CH452_DCLK_SET;             //上升沿有效
	}
  	CH452_LOAD=1;//CH452_LOAD_SET;         //加载数据,LOAD上升沿
	DELAY_1US;				//命令数据加载周期不小于6US,CH451不需要该周期
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;				//命令数据加载周期不小于6US,CH451不需要该周期
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;				//命令数据加载周期不小于6US,CH451不需要该周期
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	DELAY_1US;
	
  	ENABLE_KEY_INTERRUPT;
}

//*************************************************
//输入按键代码子程序，从CH452读取
/*unsigned char CH452_Read( void )
{
	unsigned char i;
  	unsigned char cmd,keycode;		//定义命令字，和数据存储器
  	DISABLE_KEY_INTERRUPT;			//禁止键盘中断,防止传输过程中被CH452中断而进入中断服务程序中再次传输	
  	cmd=0x07;			        //读按键的命令字
  	CH452_LOAD_CLR;
  	for(i=0;i!=4;i++)                       // 只需要发出高4位,多发也可以,但应该确保最后留下的4位是该命令码
	{
		if (cmd&1) {CH452_DIN_SET;}
		else {CH452_DIN_CLR;}           // 输出位数据
//		CH452_DIN=cmd&1;		//送入最低位
    	CH452_DCLK_CLR;			 
    	cmd>>=1;			        //往右移一位
    	CH452_DCLK_SET;			        //产生时钟上升沿锁通知CH451输入位数据
 	}
  	CH452_LOAD_SET;				//产生加载上升沿通知CH451处理命令数据
  	keycode=0;				//清除keycode
  	for(i=0;i!=7;i++)
	{
		keycode<<=1;			//数据移入keycode,高位在前,低位在后
		if (CH452_DOUT) keycode++;      //从高到低读入451的数据
//    	keycode|=CH452_DOUT;
    	CH452_DCLK_CLR;			        //产生时钟下升沿通知CH451输出下一位
    	CH452_DCLK_SET;
 	}
  	CLEAR_KEY_INTER_FLAG;	                //清中断标志
  	ENABLE_KEY_INTERRUPT;
  	return(keycode);		        //反回键值
} */