config.in

nandflash k9g808u0a在pxa270的驱动,由于pxa270没有nandflash接口

# drivers/mtd/nand/Config.in

# $Id: Config.in,v 1.2 2007/09/21 03:09:24 quy Exp $

mainmenu_option next_comment

comment 'NAND Flash Device Drivers'

dep_tristate '  NAND Device Support' CONFIG_MTD_NAND $CONFIG_MTD
if [ "$CONFIG_MTD_NAND" = "y" -o "$CONFIG_MTD_NAND" = "m" ]; then
   bool '    Verify NAND page writes' CONFIG_MTD_NAND_VERIFY_WRITE
fi

if [ "$CONFIG_ARM" = "y" ]; then
   dep_tristate '  NAND Flash device on SPIA board' CONFIG_MTD_NAND_SPIA $CONFIG_MTD_NAND $CONFIG_ARCH_P720T
   dep_tristate '  NAND Flash device on TOTO board' CONFIG_MTD_NAND_TOTO $CONFIG_MTD_NAND $CONFIG_ARCH_OMAP
   dep_tristate '  SmartMedia Card on AUTCPU12 board' CONFIG_MTD_NAND_AUTCPU12 $CONFIG_MTD_NAND $CONFIG_ARCH_AUTCPU12
   dep_tristate '  NAND Flash device on EDP7312 board' CONFIG_MTD_NAND_EDB7312 $CONFIG_MTD_NAND $CONFIG_ARCH_EDB7312
   
   dep_tristate '  NAND Flash device on K9K8G08U0A board' CONFIG_MTD_NAND_K9K8G08U0A $CONFIG_MTD_NAND
   
   dep_tristate '  iPAQ H1900 flash' CONFIG_MTD_NAND_H1900 $CONFIG_MTD_NAND $CONFIG_ARCH_PXA $CONFIG_MTD_PARTITIONS
   dep_tristate '  NAND Flash device on OMAP730 P2 board' CONFIG_MTD_NAND_P2 $CONFIG_MTD_NAND $CONFIG_MACH_OMAP_PERSEUS2
   dep_tristate '  NAND Flash device on Motorola MX2ADS board' CONFIG_MTD_NAND_MX2 $CONFIG_MTD_NAND $CONFIG_ARCH_MX2ADS
   if [ "$CONFIG_MTD_NAND_MX2" = "y" -o "$CONFIG_MTD_NAND_MX2" = "m" ]; then
   choice 'flash card' \
	"8-bit		 CONFIG_MX2_8_BIT_NAND \
	 16-bit		 CONFIG_MX2_16_BIT_NAND " 8-bit
   fi
   dep_tristate '  NAND Flash (SMC)  on SMDK24A0 board' CONFIG_MTD_NAND_S3C24A0 $CONFIG_MTD_NAND $CONFIG_ARCH_S3C24A0
   dep_tristate '  NAND Flash (SMC)  on SMDK2440 board' CONFIG_MTD_NAND_S3C2440 $CONFIG_MTD_NAND $CONFIG_ARCH_S3C2440
fi

if [ "$CONFIG_MTD_DOC2001PLUS" = "y" -o "$CONFIG_MTD_DOC2001" = "y" -o "$CONFIG_MTD_DOC2000" = "y" -o "$CONFIG_MTD_NAND" = "y" ]; then
   define_bool CONFIG_MTD_NAND_IDS y
else
  if [ "$CONFIG_MTD_DOC2001PLUS" = "m" -o "$CONFIG_MTD_DOC2001" = "m" -o "$CONFIG_MTD_DOC2000" = "m" -o "$CONFIG_MTD_NAND" = "m" ]; then
     define_bool CONFIG_MTD_NAND_IDS m
  fi
fi

if [ "$CONFIG_TOSHIBA_RBTX4925" = "y" ]; then
   dep_tristate '  SmartMedia Card on Toshiba RBTX4925 reference board' CONFIG_MTD_NAND_TX4925NDFMC $CONFIG_MTD_NAND $CONFIG_TOSHIBA_RBTX4925_MPLEX_NAND
fi

if [ "$CONFIG_TOSHIBA_RBTX4938" = "y" ]; then
   dep_tristate '  NAND Flash device on Toshiba RBTX4938 reference board' CONFIG_MTD_NAND_TX4938NDFMC $CONFIG_MTD_NAND $CONFIG_TOSHIBA_RBTX4938_MPLEX_NAND
fi

if [ "$CONFIG_PPCHAMELEONEVB" = "y" ]; then
    dep_tristate '  NAND Flash device on PPChameleonEVB board' CONFIG_MTD_NAND_PPCHAMELEONEVB $CONFIG_MTD_NAND
fi

if [ "$CONFIG_SOC_AU1550" = "y" ]; then
   dep_tristate '  NAND Flash Driver for Au1550 controller' CONFIG_MTD_NAND_AU1550 $CONFIG_MTD_NAND 
fi

dep_tristate '  DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)' CONFIG_MTD_NAND_DISKONCHIP $CONFIG_MTD_NAND $CONFIG_EXPERIMENTAL
if [ "$CONFIG_MTD_NAND_DISKONCHIP" = "y" -o "$CONFIG_MTD_NAND_DISKONCHIP" = "m" ]; then
   bool '    Advanced detection options for DiskOnChip' CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED
   hex  '    Physical address of DiskOnChip' CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS 0x00000000 
   bool '    Probe high addresses' CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH $CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED
   bool '    Allow BBT write on DiskOnChip Millennium and 2000TSOP' CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE
fi

endmenu