📄 mferrno.h
字号:
/*
* Copyright (c), Philips Semiconductors Gratkorn / Austria
*
* (C)PHILIPS Electronics N.V.2000
* All rights are reserved. Reproduction in whole or in part is
* prohibited without the written consent of the copyright owner.
* Philips reserves the right to make changes without notice at any time.
* Philips makes no warranty, expressed, implied or statutory, including but
* not limited to any implied warranty of merchantability or fitness for any
*particular purpose, or that the use will not infringe any third party patent,
* copyright or trademark. Philips must not be liable for any loss or damage
* arising from its use.
*/
/*! \file MfErrno.h
*
* Projekt: MF EV X00 Firmware
*
* $Workfile:: MfErrno.h $
* $Modtime:: 30.03.01 6:15 $
* $Author:: Hb $
* $Revision:: 20 $
*
* General purpose error message file for various reader IC's
* <ul>
* <li> RC150
* <li> RC171
* <li> RC500
* </ul>
*/
#ifndef MFERRNO_H
#define MFERRNO_H
#ifdef __cplusplus
extern "C" {
#endif
//////////////////////////////////////////////////////////////////////////////
// INCLUDES
//////////////////////////////////////////////////////////////////////////////
#include <OsDefs.h>
//////////////////////////////////////////////////////////////////////////////
// Reader Error Codes Base Address Start: 0000
// Base Address End: -999
//////////////////////////////////////////////////////////////////////////////
#define READER_ERR_BASE_START 0
#define MI_OK 0
#define MI_CHK_OK 0
#define MI_CRC_ZERO 0
#define MI_CRC_NOTZERO 1
#define MI_NOTAGERR (-1)
#define MI_CHK_FAILED (-1)
#define MI_CRCERR (-2)
#define MI_CHK_COMPERR (-2)
#define MI_EMPTY (-3)
#define MI_AUTHERR (-4)
#define MI_PARITYERR (-5)
#define MI_CODEERR (-6)
#define MI_SERNRERR (-8)
#define MI_KEYERR (-9)
#define MI_NOTAUTHERR (-10)
#define MI_BITCOUNTERR (-11)
#define MI_BYTECOUNTERR (-12)
#define MI_IDLE (-13)
#define MI_TRANSERR (-14)
#define MI_WRITEERR (-15)
#define MI_INCRERR (-16)
#define MI_DECRERR (-17)
#define MI_READERR (-18)
#define MI_OVFLERR (-19)
#define MI_POLLING (-20)
#define MI_FRAMINGERR (-21)
#define MI_ACCESSERR (-22)
#define MI_UNKNOWN_COMMAND (-23)
#define MI_COLLERR (-24)
#define MI_RESETERR (-25)
#define MI_INITERR (-25)
#define MI_INTERFACEERR (-26)
#define MI_ACCESSTIMEOUT (-27)
#define MI_NOBITWISEANTICOLL (-28)
#define MI_QUIT (-30)
#define MI_RECBUF_OVERFLOW (-50)
#define MI_SENDBYTENR (-51)
#define MI_SENDBUF_OVERFLOW (-53)
#define MI_BAUDRATE_NOT_SUPPORTED (-54)
#define MI_SAME_BAUDRATE_REQUIRED (-55)
#define MI_WRONG_PARAMETER_VALUE (-60)
#define MI_BREAK (-99)
#define MI_NY_IMPLEMENTED (-100)
#define MI_NO_MFRC (-101)
#define MI_MFRC_NOTAUTH (-102)
#define MI_WRONG_DES_MODE (-103)
#define MI_HOST_AUTH_FAILED (-104)
#define MI_WRONG_LOAD_MODE (-106)
#define MI_WRONG_DESKEY (-107)
#define MI_MKLOAD_FAILED (-108)
#define MI_FIFOERR (-109)
#define MI_WRONG_ADDR (-110)
#define MI_DESKEYLOAD_FAILED (-111)
#define MI_WRONG_SEL_CNT (-114)
#define MI_WRONG_TEST_MODE (-117)
#define MI_TEST_FAILED (-118)
#define MI_TOC_ERROR (-119)
#define MI_COMM_ABORT (-120)
#define MI_INVALID_BASE (-121)
#define MI_MFRC_RESET (-122)
#define MI_WRONG_VALUE (-123)
#define MI_VALERR (-124)
#ifdef __cplusplus
}
#endif
#endif // COMMON_H
//////////////////////////////////////////////////////////////////////////////
// End of File
//////////////////////////////////////////////////////////////////////////////
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -