sscom.ini

与不同的外部设备连接需要不同的通讯电缆。为避免发生通讯的问题

;这是SSCOM的设置保存文件,您在程序中设置好的串口参数和字符串数据都会自动保存,请最好不要用外部编辑器改动本文件!
;如果文件被修改后程序不能打开,请删除本文件,程序将会自动生成一个新的ini文件.
;靠行首的半角分号是注释符号
;每行都以回车结束

;当前串口号Port
N80=,COM4
;波特率Band rate
N81=,9600
;数据位Data bits
N82=,8
;停止位Stop bits
N83=,1
;校验位Parity
;N84=,无法保存,请打开软件后重新设置
;流控Flow control
;N85=,无法保存,请打开软件后重新设置

;"="后面的H表示这是个HEX数据串
;"="后面的A表示这是个ASC字符串
;Nx表示第几条定义的字符串(1<x<32)
N1=H,F0 5A 11 07 09 02 04 15 56 00 A5 F0 
N2=H,F0 5A 17 11 00 ff 00 01 00 01 00 A5 F0
N3=H,F0 5A 21 00 10 10 00 aa bb 03 04 05 06 07 08 09 A5 F0
N4=H,F0 5A 22 00 10 10  A5 F0
N5=H,F0 5A 89 4C 43 44 CED2 A5 F0
N6=H,f0 5a 1a a5 f0
N7=H,F0 5A 83 01 24 24 A5 F0
N8=H,F0 5A 8A CED24C 43 44 B2 E2 CA D4 B3 CC D0 F2 A5 F0
N9=H,F0 5A 17 11 00 FF 00 00 00 00 00 00 00 00 00 A5 F0
N10=H,F0 5A 91 00 00 00 00 00 00 A5 F0
N11=H,F0 5A 17 11 00 01 00 00 00 00 00 A5 F0
N12=H,F0 5A 12 A5 F0
N13=H,F0 5A 91 00 01 00 00 00 00 A5 F0
N14=A,f0 5a 1a a5 f0
N15=A,
N16=H,F0 5A 91 00 02 01 00 01 00  A5 F0
N17=H,F0 5A 82 00 A5 F0
N18=H,F0 5A 82 00 00 ff A5 F0
N19=H,F0 5A 85 ff ff 00 A5 F0
N20=H,F0 5A 81 02 40 02 00 01 A5 F0
N21=H,F0 5A 83 01 24 24 A5 F0
N22=H,f0 5a 35 01 a5 f0
N23=H,f0 5a 36 00 a5 f0
N24=H,F0 5A 92 00 40 00 40 01 10 A5 F0
N25=H,F0 5A 93 00 00 00 00 01 00 00 40 01 A5 F0
N26=H,F0 5A 94 00 40 00 40 00 30 01 A5 F0
N27=H,F0 5A 95 00 99 00 40 00 00 00 00 01 01 A5 F0
N28=H,F0 5A 96 00 99 00 99 00 00 00 00 A5 F0
N29=H,F0 5A 92 01 00 01 00 FF 00 00 10 A5 F0
N30=H,F0 5A 93 00 00 00 00 01 00 01 00 FF 00 00 A5 F0
N31=H,F0 5A 94 01 00 01 00 01 00 FF 00 00 A5 F0
N32=H,F0 5A 96 00 99 00 99 00 00 00 00 A5 F00

;主面板ASC字符串
N33=,
;主面板HEX数据串
N34=,F0 5A 8A CED24C 43 44 B2 E2 CA D4 B3 CC D0 F2 A5 F0
;主面板发送方式(ASC or HEX)
N35=,H
;主面板字符串发送间隔时间
N36=,2000
;主面板字符串发送新行
N37=,N
;多条字符串发送间隔时间
N38=,1000
;end