dactest.c

2812的经典示例程序

//###########################################################################
//
// FILE:   DACtest.c
//
// TITLE:  DSP281x Device DAC test porgram. 

#include "DSP281x_Device.h"     // DSP281x Headerfile Include File
#include "DSP281x_Examples.h"   // DSP281x Examples Include File

// Prototype statements for functions found within this file.
// interrupt void ISRTimer2(void);
interrupt void spiTxFifoIsr(void);
interrupt void spiRxFifoIsr(void);
void delay_loop(void);
void spi_fifo_init(void);	
void error();

Uint16 sdata[8];     // Send data buffer
Uint16 rdata[8];     // Receive data buffer
Uint16 rdata_point;  // Keep track of where we are 
                     // in the data stream to check received data
                     
void main(void)
{
   Uint16 i;   
      
// Step 1. Initialize System Control:
// PLL, WatchDog, enable Peripheral Clocks
// This example function is found in the DSP281x_SysCtrl.c file.
   InitSysCtrl();

// Step 2. Initalize GPIO: 
// This example function is found in the DSP281x_Gpio.c file and
// illustrates how to set the GPIO to it's default state.
// InitGpio();  // Skipped for this example  
// Setup only the GP I/O only for SPI functionality
   EALLOW;
   GpioMuxRegs.GPFMUX.all=0x000F;	// Select GPIOs to be SPI pins	 
                                    // Port F MUX - x000 0000 0000 1111
   EDIS;

// Step 3. Initialize PIE vector table:
// Disable and clear all CPU interrupts
   DINT;
   IER = 0x0000;
   IFR = 0x0000;

// Initialize PIE control registers to their default state:
// This function is found in the DSP281x_PieCtrl.c file.
   InitPieCtrl();

// Initialize the PIE vector table with pointers to the shell Interrupt 
// Service Routines (ISR).  
// This will populate the entire table, even if the interrupt
// is not used in this example.  This is useful for debug purposes.
// The shell ISR routines are found in DSP281x_DefaultIsr.c.
// This function is found in DSP281x_PieVect.c.
   InitPieVectTable();

// Interrupts that are used in this example are re-mapped to
// ISR functions found within this file.  
   EALLOW;	// This is needed to write to EALLOW protected registers
   PieVectTable.SPIRXINTA = &spiRxFifoIsr;
   PieVectTable.SPITXINTA = &spiTxFifoIsr;
   EDIS;   // This is needed to disable write to EALLOW protected registers
   
   //Init SCITXA,RXA as io ports 
   EALLOW;
     GpioMuxRegs.GPFMUX.bit.SCITXDA_GPIOF4 =0;
     GpioMuxRegs.GPFMUX.bit.SCIRXDA_GPIOF5 =0;     
     GpioMuxRegs.GPFDIR.bit.GPIOF4 =1;
     GpioMuxRegs.GPFDIR.bit.GPIOF5 =1;    	// upper byte as output/low byte as input
     GpioMuxRegs.GPAQUAL.all=0x0000;	// Input qualifier disabled
   EDIS;

	
// Step 4. Initialize all the Device Peripherals:
// This function is found in DSP281x_InitPeripherals.c
// InitPeripherals(); // Not required for this example
   spi_fifo_init();	  // Initialize the SPI only

	
// Step 5. User specific code, enable interrupts:

// Initalize the send data buffer
   for(i=0; i<8; i++)
   {
      sdata[i] = i;
   }      
   rdata_point = 0;
   GpioDataRegs.GPFDAT.bit.GPIOF4=1;
   GpioDataRegs.GPFDAT.bit.GPIOF5 =0; 
// Enable interrupts required for this example
   PieCtrlRegs.PIECRTL.bit.ENPIE = 1;   // Enable the PIE block
 //  PieCtrlRegs.PIEIER6.bit.INTx1=1;     // Enable PIE Group 6, INT 1
   PieCtrlRegs.PIEIER6.bit.INTx2=1;     // Enable PIE Group 6, INT 2
   IER=0x20;                            // Enable CPU INT6
   EINT;                                // Enable Global Interrupts
	
// Step 6. IDLE loop. Just sit and loop forever (optional):	
	for(;;);

} 	


// Some Useful local functions
void delay_loop()
{
    long      i;
    for (i = 0; i < 1000000; i++) {}
}


void error(void)
{
    asm("     ESTOP0");	 //Test failed!! Stop!
    for (;;);
}


void spi_fifo_init()										
{
// Initialize SPI FIFO registers for DA
   SpiaRegs.SPICCR.bit.SPISWRESET=0; // Reset SPI

   SpiaRegs.SPICCR.all=0x000F;       //16-bit character, no Loopback mode 
   SpiaRegs.SPICTL.all=0x0017;       //Interrupt enabled, Master/Slave XMIT enabled
   SpiaRegs.SPISTS.all=0x0000;
   SpiaRegs.SPIBRR=0x0063;           // Baud rate
   SpiaRegs.SPIFFTX.all=0xC028;      // Enable FIFO's, set TX FIFO level to 8
   SpiaRegs.SPIFFRX.all=0x0028;      // Set RX FIFO level to 31
   SpiaRegs.SPIFFCT.all=0x00;
   SpiaRegs.SPIPRI.all=0x0010;
    
   SpiaRegs.SPICCR.bit.SPISWRESET=1;  // Enable SCI

   SpiaRegs.SPIFFTX.bit.TXFIFO=1;
   SpiaRegs.SPIFFRX.bit.RXFIFORESET=1;
}

interrupt void spiTxFifoIsr(void)
{
 
    SpiaRegs.SPITXBUF=0x1fff;      // Send data
    SpiaRegs.SPIFFTX.bit.TXFFINTCLR=1;  // Clear Interrupt flag
	PieCtrlRegs.PIEACK.all|=0x20;  		// Issue PIE ACK
}

interrupt void spiRxFifoIsr(void)
{      
    Uint16 i;
    for(i=0;i<8;i++)
    {
	    rdata[i]=SpiaRegs.SPIRXBUF;		// Read data
	}
	for(i=0;i<8;i++)                    // Check received data
	{
	    if(rdata[i] != rdata_point+i) error();
	}
	rdata_point++;
	SpiaRegs.SPIFFRX.bit.RXFFOVFCLR=1;  // Clear Overflow flag
	SpiaRegs.SPIFFRX.bit.RXFFINTCLR=1; 	// Clear Interrupt flag
	PieCtrlRegs.PIEACK.all|=0x20;       // Issue PIE ack
}
  


//===========================================================================
// No more.
//===========================================================================