opt.h

LWIP1.1.1在UCOS-II2.61上的移植

#ifndef __LWIP_OPT_H__
#define __LWIP_OPT_H__

/* Include user defined options first */
#include "lwipopts.h"
#include "lwip/debug.h"

/* Define default values for unconfigured parameters. */

/* Platform specific locking */

/*
 * enable SYS_LIGHTWEIGHT_PROT in lwipopts.h if you want inter-task protection
 * for certain critical regions during buffer allocation, deallocation and memory
 * allocation and deallocation.
 */
#ifndef SYS_LIGHTWEIGHT_PROT
#define SYS_LIGHTWEIGHT_PROT            0
#endif

#ifndef NO_SYS
#define NO_SYS                          0
#endif
/* ---------- Memory options ---------- */
/* MEM_ALIGNMENT: should be set to the alignment of the CPU for which
   lwIP is compiled. 4 byte alignment -> define MEM_ALIGNMENT to 4, 2
   byte alignment -> define MEM_ALIGNMENT to 2. */

#ifndef MEM_ALIGNMENT
#define MEM_ALIGNMENT                   1
#endif

/* MEM_SIZE: the size of the heap memory. If the application will send
a lot of data that needs to be copied, this should be set high. */
#ifndef MEM_SIZE
#define MEM_SIZE                        1600
#endif

#ifndef MEMP_SANITY_CHECK
#define MEMP_SANITY_CHECK       1
#endif

/* MEMP_NUM_PBUF: the number of memp struct pbufs. If the application
   sends a lot of data out of ROM (or other static memory), this
   should be set high. */
#ifndef MEMP_NUM_PBUF
#define MEMP_NUM_PBUF                   16
#endif

/* Number of raw connection PCBs */
#ifndef MEMP_NUM_RAW_PCB
#define MEMP_NUM_RAW_PCB                4
#endif

/* MEMP_NUM_UDP_PCB: the number of UDP protocol control blocks. One
   per active UDP "connection". */
#ifndef MEMP_NUM_UDP_PCB
#define MEMP_NUM_UDP_PCB                4
#endif
/* MEMP_NUM_TCP_PCB: the number of simulatenously active TCP
   connections. */
#ifndef MEMP_NUM_TCP_PCB
#define MEMP_NUM_TCP_PCB                5
#endif
/* MEMP_NUM_TCP_PCB_LISTEN: the number of listening TCP
   connections. */
#ifndef MEMP_NUM_TCP_PCB_LISTEN
#define MEMP_NUM_TCP_PCB_LISTEN         8
#endif
/* MEMP_NUM_TCP_SEG: the number of simultaneously queued TCP
   segments. */
#ifndef MEMP_NUM_TCP_SEG
#define MEMP_NUM_TCP_SEG                16
#endif
/* MEMP_NUM_SYS_TIMEOUT: the number of simulateously active
   timeouts. */
#ifndef MEMP_NUM_SYS_TIMEOUT
#define MEMP_NUM_SYS_TIMEOUT            3
#endif

/* The following four are used only with the sequential API and can be
   set to 0 if the application only will use the raw API. */
/* MEMP_NUM_NETBUF: the number of struct netbufs. */
#ifndef MEMP_NUM_NETBUF
#define MEMP_NUM_NETBUF                 2
#endif
/* MEMP_NUM_NETCONN: the number of struct netconns. */
#ifndef MEMP_NUM_NETCONN
#define MEMP_NUM_NETCONN                4
#endif
/* MEMP_NUM_APIMSG: the number of struct api_msg, used for
   communication between the TCP/IP stack and the sequential
   programs. */
#ifndef MEMP_NUM_API_MSG
#define MEMP_NUM_API_MSG                8
#endif
/* MEMP_NUM_TCPIPMSG: the number of struct tcpip_msg, which is used
   for sequential API communication and incoming packets. Used in
   src/api/tcpip.c. */
#ifndef MEMP_NUM_TCPIP_MSG
#define MEMP_NUM_TCPIP_MSG              8
#endif

/* ---------- Pbuf options ---------- */
/* PBUF_POOL_SIZE: the number of buffers in the pbuf pool. */

#ifndef PBUF_POOL_SIZE
#define PBUF_POOL_SIZE                  16
#endif

/* PBUF_POOL_BUFSIZE: the size of each pbuf in the pbuf pool. */

#ifndef PBUF_POOL_BUFSIZE
#define PBUF_POOL_BUFSIZE               128
#endif

/* PBUF_LINK_HLEN: the number of bytes that should be allocated for a
   link level header. Defaults to 14 for Ethernet. */

#ifndef PBUF_LINK_HLEN
#define PBUF_LINK_HLEN                  14
#endif



/* ---------- ARP options ---------- */

/** Number of active hardware address, IP address pairs cached */
#ifndef ARP_TABLE_SIZE
#define ARP_TABLE_SIZE                  10
#endif

/**
 * If enabled, outgoing packets are queued during hardware address
 * resolution.
 *
 * This feature has not stabilized yet. Single-packet queueing is
 * believed to be stable, multi-packet queueing is believed to
 * clash with the TCP segment queueing.
 * 
 * As multi-packet-queueing is currently disabled, enabling this
 * _should_ work, but we need your testing feedback on lwip-users.
 *
 */
#ifndef ARP_QUEUEING
#define ARP_QUEUEING                    1
#endif

/* This option is deprecated */
#ifdef ETHARP_QUEUE_FIRST
#error ETHARP_QUEUE_FIRST option is deprecated. Remove it from your lwipopts.h.
#endif

/* This option is removed to comply with the ARP standard */
#ifdef ETHARP_ALWAYS_INSERT
#error ETHARP_ALWAYS_INSERT option is deprecated. Remove it from your lwipopts.h.
#endif

/* ---------- IP options ---------- */
/* Define IP_FORWARD to 1 if you wish to have the ability to forward
   IP packets across network interfaces. If you are going to run lwIP
   on a device with only one network interface, define this to 0. */
#ifndef IP_FORWARD
#define IP_FORWARD                      0
#endif

/* If defined to 1, IP options are allowed (but not parsed). If
   defined to 0, all packets with IP options are dropped. */
#ifndef IP_OPTIONS
#define IP_OPTIONS                      1
#endif

/** IP reassembly and segmentation. Even if they both deal with IP
 *  fragments, note that these are orthogonal（正交）, one dealing with incoming
 *  packets, the other with outgoing packets
 */

/** Reassemble incoming fragmented IP packets */
#ifndef IP_REASSEMBLY
#define IP_REASSEMBLY                   1
#endif

/** Fragment outgoing IP packets if their size exceeds MTU */
#ifndef IP_FRAG
#define IP_FRAG                         1
#endif

/* ---------- ICMP options ---------- */

#ifndef ICMP_TTL
#define ICMP_TTL                        255
#endif

/* ---------- RAW options ---------- */

#ifndef LWIP_RAW
#define LWIP_RAW                        1
#endif

#ifndef RAW_TTL
#define RAW_TTL                        255
#endif

/* ---------- DHCP options ---------- */

#ifndef LWIP_DHCP
#define LWIP_DHCP                       0
#endif

/*  if you want to do an ARP check on the offered address
   (recommended推荐). */
#ifndef DHCP_DOES_ARP_CHECK
#define DHCP_DOES_ARP_CHECK             1
#endif

/* ---------- UDP options ---------- */
#ifndef LWIP_UDP
#define LWIP_UDP                        1
#endif

#ifndef UDP_TTL
#define UDP_TTL                         255
#endif

/* ---------- TCP options ---------- */
#ifndef LWIP_TCP
#define LWIP_TCP                        1
#endif

#ifndef TCP_TTL
#define TCP_TTL                         255
#endif

#ifndef TCP_WND
#define TCP_WND                         2048
#endif 

#ifndef TCP_MAXRTX
#define TCP_MAXRTX                      12
#endif

#ifndef TCP_SYNMAXRTX
#define TCP_SYNMAXRTX                   6
#endif


/* Controls if TCP should queue segments that arrive out of
   order. Define to 0 if your device is low on memory. */
#ifndef TCP_QUEUE_OOSEQ
#define TCP_QUEUE_OOSEQ                 1
#endif

/* TCP Maximum segment size. */
#ifndef TCP_MSS
#define TCP_MSS                         128 /* A *very* conservative default. */
#endif

/* TCP sender buffer space (bytes). */
#ifndef TCP_SND_BUF
#define TCP_SND_BUF                     256
#endif

/* TCP sender buffer space (pbufs). This must be at least = 2 *
   TCP_SND_BUF/TCP_MSS for things to work. */
#ifndef TCP_SND_QUEUELEN
#define TCP_SND_QUEUELEN                4 * TCP_SND_BUF/TCP_MSS
#endif


/* Maximum number of retransmissions of data segments. */

/* Maximum number of retransmissions of SYN segments. */

/* TCP writable space (bytes). This must be less than or equal
   to TCP_SND_BUF. It is the amount of space which must be
   available in the tcp snd_buf for select to return writable */
#ifndef TCP_SNDLOWAT
#define TCP_SNDLOWAT                    TCP_SND_BUF/2
#endif

/* Support loop interface (127.0.0.1) */
#ifndef LWIP_HAVE_LOOPIF
#define LWIP_HAVE_LOOPIF                0  
#endif

#ifndef LWIP_EVENT_API
#define LWIP_EVENT_API                  0
#define LWIP_CALLBACK_API               1
#else 
#define LWIP_EVENT_API                  1
#define LWIP_CALLBACK_API               0
#endif 

#ifndef LWIP_COMPAT_SOCKETS
#define LWIP_COMPAT_SOCKETS             1
#endif


#ifndef TCPECHO_THREAD_PRIO
#define TCPECHO_THREAD_PRIO               1
#endif

#ifndef UDPECHO_THREAD_PRIO
#define UDPECHO_THREAD_PRIO               1
#endif

#ifndef TCPIP_THREAD_PRIO
#define TCPIP_THREAD_PRIO               1
#endif

#ifndef SLIPIF_THREAD_PRIO
#define SLIPIF_THREAD_PRIO              1
#endif

#ifndef PPP_THREAD_PRIO
#define PPP_THREAD_PRIO                 1
#endif

#ifndef DEFAULT_THREAD_PRIO
#define DEFAULT_THREAD_PRIO             1
#endif


/* ---------- Socket Options ---------- */
/* Enable SO_REUSEADDR and SO_REUSEPORT options */ 
#ifdef SO_REUSE
/* I removed the lot since this was an ugly hack. It broke the raw-API.
   It also came with many ugly goto's, Christiaan Simons.
   处理器命令#error强迫编译程序停止编译，主要用于程序调试。 */
#error SO_REUSE currently unavailable, this was a hack
#endif                                                                        


/* ---------- Statistics options ---------- */
#ifndef LWIP_STATS
#define LWIP_STATS                      0
#endif

#if LWIP_STATS

#ifndef LWIP_STATS_DISPLAY
#define LWIP_STATS_DISPLAY 0
#endif

#ifndef LINK_STATS