mc1319xsard.h

采用MC13213做的在SMAC协议基础上的发送程序,可作为点对点实验中的END DEVICE.

/* toro_gen_header.h 
 * toro header for test verification

 * $Author: a20639 $
 * $Date: 2006/08/25 14:55:00 $
 * $Name:  $
 */
 
//includes
#include "pub_def.h"
#include "board_config.h"

//Prototypes
void RadioInit(void);
//Defines
/* SARD */


/**************************************************************
SMAC Required defines
**************************************************************/
#define HCS08G																	 /*!<HCS06G family member*/
#define MC13192_CE              PTED_PTED2       /*!<Enables SPI transfers*/         
#define MC13192_CE_PORT         PTEDD_PTEDD2     /*!<SPI enable pin data direction*/           
#define MC13192_ATTN            PTCD_PTCD2			 /*!<Transitions IC from either Hibernate 
                                                    or Doze Modes to Idle. */
#define MC13192_ATTN_PORT       PTCDD_PTCDD2		 /*!<ATTN pin data direction */
#define MC13192_RTXEN           PTCD_PTCD3			 /*!<Enables Transmission or Reception from SPI */
#define MC13192_RTXEN_PORT      PTCDD_PTCDD3		 /*!<SPI Transmission pin direction */
#define MC13192_RESET           PTCD_PTCD4			 /*!<Transciever Reset */
#define MC13192_RESET_PORT      PTCDD_PTCDD4		 /*!<Transciever Reset pin data direction */
#define MC13192_RESET_PULLUP    PTCPE_PTCPE4		 /*!<Enables pull up for Reset */
#define MC13192_IRQ_SOURCE      IRQSC						 /*!<IRQ register*/
#define MC13192_IRQ_IE_BIT      IRQSC_IRQIE			 /*!<Enables IRQ pin*/

#ifdef ANTENNA_SWITCH
    #define MC13192_ANT_CTRL        PTBD_PTBD6	 /*!<Control line 1 for antenna*/
    #define MC13192_ANT_CTRL2       PTBD_PTBD6   /*!< 
                                                  * Second Control line not
                                                  * used in MC13192EVB
                                                  */
    #define MC13192_ANT_CTRL_PORT   PTBDD_PTBDD6 /*!<Control line port data direction*/
    #define MC13192_ANT_CTRL2_PORT  PTBDD_PTBDD6 /*!< 
                                                  * Second Control line not 
                                                  * used in MC13192EVB
                                                  */
    #define ANT_CTRL_OFF            0       /*!<Antenna Control Logic low is off */
    #define ANT_CTRL_ON             1       /*!<Antenna Control Logic high is on */
#endif ANTENNA_SWITCH

#ifdef LNA
    #define MC13192_LNA_CTRL        PTBD_PTBD0		/*!<LNA Control*/
    #define MC13192_LNA_CTRL_PORT   PTBDD_PTBDD0  /*!<LNA control pin direction */
    #define LNA_ON                  1							/*!<Turns on LNA*/
    #define LNA_OFF                 0							/*!<Turns of LNA */
#endif LNA  




/**************************************************************
Enable peripherials that are on the Board
**************************************************************/
#define ACCEL_ENABLED         TRUE
#define TEMP_SENSOR_ENABLED   FALSE
#define BUZZER_ENABLED        FALSE
#define BUS_SPEED	            8000000

/**************************************************************
Define the SCI perameters
**************************************************************/
#define  SCIBDH     SCI1BDH
#define  SCIBDL     SCI1BDL
#define  SCIC1      SCI1C1 
#define  SCIC2      SCI1C2 
#define  SCIS1      SCI1S1 
#define  SCIS2      SCI1S2 
#define  SCIC3      SCI1C3 
#define  SCID       SCI1D

#define  SCIS1_TDRE  SCI1S1_TDRE
#define  SCIS1_TC    SCI1S1_TC

#define  RTS			PTAD_PTAD1
#define  RTSDIR		  	PTADD_PTADD1
#define  SCI_DEFAULT_BAUD  38400
/**************************************************************
Define the LED perameters
**************************************************************/

#define LED1                    PTDD_PTDD4
#define LED1DIR                 PTDDD_PTDDD4
#define LED2                    PTDD_PTDD3
#define LED2DIR                 PTDDD_PTDDD3
#define LED3                    PTDD_PTDD1
#define LED3DIR                 PTDDD_PTDDD1
#define LED4                    PTDD_PTDD0
#define LED4DIR                 PTDDD_PTDDD0

/* Fifth LED is not defined for GB60EVB, set to Port D pin 5 */
#define LED5						  PTDD_PTDD5
#define LED5DIR                 PTDDD_PTDDD5
    
#define LED_ON                  0
#define LED_OFF					1
#define DDIR_OUTPUT             1
#define DDIR_INPUT              0
    
#define LED_INIT_MACRO LED1     = LED_OFF; \
                       LED2     = LED_OFF; \
                       LED3     = LED_OFF; \
                       LED4     = LED_OFF; \
                       LED5     = LED_OFF; \
                       LED1DIR  = DDIR_OUTPUT; \
                       LED2DIR  = DDIR_OUTPUT; \
                       LED3DIR  = DDIR_OUTPUT; \
                       LED4DIR  = DDIR_OUTPUT; \
                       LED5DIR  = DDIR_OUTPUT;        
    
    
/***********************************************
Define Switches
***********************************************/
        
/* SW1 on schematic */
#define PB0 PTAD_PTAD2
#define PB0PU PTAPE_PTAPE2
#define PB0DIR PTADD_PTADD2
#define PB0IE KBI1PE_KBIPE2
  
/* SW2 on schematic */
#define PB1 PTAD_PTAD3
#define PB1PU PTAPE_PTAPE3
#define PB1DIR PTADD_PTADD3
#define PB1IE KBI1PE_KBIPE3
   
/* SW3 on schematic */
#define PB2 PTAD_PTAD4
#define PB2PU PTAPE_PTAPE4
#define PB2DIR PTADD_PTADD4
#define PB2IE KBI1PE_KBIPE4
  
/* SW4 on schematic */
#define PB3 PTAD_PTAD5
#define PB3PU PTAPE_PTAPE5
#define PB3DIR PTADD_PTADD5
#define PB3IE KBI1PE_KBIPE5

/* Define the KBI Pins */
#define KBI_SW1 0x04
#define KBI_SW2 0x08
#define KBI_SW3 0x10
#define KBI_SW4 0x20


#define SWITCH_INIT_MACRO    PB0PU = TRUE; \
                             PB1PU = TRUE; \
                             PB2PU = TRUE; \
                             PB3PU = TRUE; \
                             PB0DIR = FALSE;\
                             PB1DIR = FALSE;\
                             PB2DIR = FALSE;\
                             PB3DIR = FALSE;
                              
#define ENTER_LOW_POWER _asm stop


/***********************************************
Duplicate PB0 to PUSH_BUTTON1 etc for different
formats.
***********************************************/

#define PUSH_BUTTON1 PB0
#define PUSH_BUTTON2 PB1
#define PUSH_BUTTON3 PB2
#define PUSH_BUTTON4 PB3

#define PB_PRESSED 0


/***********************************************
Define Port B
Accelerometer and LCD
***********************************************/

#define ACCEL_PS          PTCD_PTCD5
#define ACCEL_GSELECT1    PTCD_PTCD6
#define ACCEL_GSELECT2    PTGD_PTGD1
#define ACCEL_START_X     ATD1SC = 0;
#define ACCEL_START_Y     ATD1SC = 1;
#define ACCEL_START_Z     ATD1SC = 7;         
  
#define ACCEL_INIT_MACRO  ATD1PE=0x83; ATD1C=0xE1;\
                          PTBDD_PTBDD0=DDIR_OUTPUT;\
                          PTBDD_PTBDD1=DDIR_OUTPUT;\
                          PTBDD_PTBDD7=DDIR_OUTPUT; 
                          
#define ACCEL_G_OFF       ACCEL_PS = 0;
#define ACCEL_G_ON        ACCEL_PS = 1; 
#define ACCEL_G_1p5       ACCEL_GSELECT1 = 0; ACCEL_GSELECT2 = 0;
#define ACCEL_G_2p0       ACCEL_GSELECT1 = 0; ACCEL_GSELECT2 = 1;
#define ACCEL_G_4p0       ACCEL_GSELECT1 = 1; ACCEL_GSELECT2 = 0;
#define ACCEL_G_6p0       ACCEL_GSELECT1 = 1; ACCEL_GSELECT2 = 1;