mainloop.h

small rtos在周立功的开发板dp51上的使用示例

#ifndef __MAINLOOP_H__
#define __MAINLOOP_H__


sbit D12_CS	  = P1^6;
sbit D12_RST   = P1^7;
sbit USB_VIN	= P3^4;

sbit	KD_KEY = P1^2;
sbit	SDA=P1^0;
sbit	CLK=P1^1;
sbit	LED_CS=P1^7;

sfr CKCON = 0x8f;


#define MAX_CONTROLDATA_SIZE	8


//信号量序号定义
#define USB_setup				0
#define D12_use					1
#define D12_isr					2


/*
   //*************************************************************************
   // basic #defines
   //*************************************************************************
   */
#define MAX_ENDPOINTS      (unsigned char)0x3

#define EP0_TX_FIFO_SIZE   16
#define EP0_RX_FIFO_SIZE   16
#define EP0_PACKET_SIZE    16

#define EP1_TX_FIFO_SIZE   16
#define EP1_RX_FIFO_SIZE   16
#define EP1_PACKET_SIZE    16

#define EP2_TX_FIFO_SIZE   64
#define EP2_RX_FIFO_SIZE   64
#define EP2_PACKET_SIZE    64


#define USB_IDLE           0
#define USB_TRANSMIT       1
#define USB_RECEIVE        2

#define USB_CLASS_CODE_TEST_CLASS_DEVICE                    0xdc
#define USB_SUBCLASS_CODE_TEST_CLASS_D12                    0xA0
#define USB_PROTOCOL_CODE_TEST_CLASS_D12                    0xB0

/*
   //*************************************************************************
   // masks
   //*************************************************************************
*/

#define USB_RECIPIENT            (unsigned char)0x1F
#define USB_RECIPIENT_DEVICE     (unsigned char)0x00
#define USB_RECIPIENT_INTERFACE  (unsigned char)0x01
#define USB_RECIPIENT_ENDPOINT   (unsigned char)0x02

#define USB_REQUEST_TYPE_MASK    (unsigned char)0x60
#define USB_STANDARD_REQUEST     (unsigned char)0x00
#define USB_CLASS_REQUEST        (unsigned char)0x20
#define USB_VENDOR_REQUEST       (unsigned char)0x40

#define USB_REQUEST_MASK         (unsigned char)0x0F

#define DEVICE_ADDRESS_MASK      0x7F

/*
   //*************************************************************************
   // macros
   //*************************************************************************
*/
#define SWAP(x)   ((((x) & 0xFF) << 8) | (((x) >> 8) & 0xFF))

#define MSB(x)    (((x) >> 8) & 0xFF)
#define LSB(x)    ((x) & 0xFF)

#define FALSE   0
//#define TRUE    (!FALSE)

/*
   //*************************************************************************
   // basic typedefs
   //*************************************************************************
*/
typedef unsigned char   UCHAR;
typedef unsigned short  USHORT;
typedef unsigned long   ULONG;
typedef unsigned char   BOOL;

/*
   //*************************************************************************
   // structure and union definitions
   //*************************************************************************
*/
typedef union _epp_flags
{
	struct _flags
	{
		unsigned char timer               	: 1;
		unsigned char bus_reset           	: 1;
		unsigned char suspend             	: 1;
		unsigned char setup_packet  	  	: 1;
		unsigned char remote_wakeup		   	: 1;
		unsigned char in_isr		      	: 1;
		unsigned char control_state			: 2;

		unsigned char configuration			: 1;
		unsigned char verbose				: 1;
		unsigned char ep1_rxdone			: 1;
		unsigned char setup_dma				: 2; // V2.3
		unsigned char dma_state      		: 2;
		unsigned char power_down			: 1; // Smart Board
	} bits;
	unsigned short value;
} EPPFLAGS;


typedef struct _device_request
{
	unsigned char bmRequestType;
	unsigned char bRequest;
	unsigned short wValue;
	unsigned short wIndex;
	unsigned short wLength;
} DEVICE_REQUEST;

typedef struct _control_xfer
{
	DEVICE_REQUEST DeviceRequest;
	unsigned short wLength;
	unsigned short wCount;
	unsigned char * pData;
	unsigned char dataBuffer[MAX_CONTROLDATA_SIZE];
} CONTROL_XFER;

typedef struct _IO_REQUEST {
	unsigned short	uAddressL;
	unsigned char	bAddressH;
	unsigned short	uSize;
	unsigned char	bCommand;
} IO_REQUEST, *PIO_REQUEST;



void enumerate(void);
void usb_isr(void);
void check_key_LED(void);
void send(unsigned char a);
extern void reconnect_USB(void);
extern void control_handler(void);


#endif