bootmesg.txt

9200的开发资料：包括uboot

## Booting image at 21000000 ...
   Image Name:   
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    655773 Bytes = 640.4 kB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.4.19-rmk7 (amine@PC0142) (gcc version 2.95.3 20010315 (release)) #27 Wed Jul 9 13:45:35 CEST 2003
CPU: Arm920Tid(wb) revision 0
Machine: ATMEL AT91RM9200
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram rw initrd=0x21100000,6000000 ramdisk_size=15360 console=ttyS0,115200 mem=32M
Console: colour dummy device 80x30
Calibrating delay loop... 89.70 BogoMIPS
Memory: 32MB = 32MB total
Memory: 24952KB available (1226K code, 263K data, 72K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch ([e-mail])
devfs: boot_options: 0x1
S1D13XXX: Phys address:C2802000 Phys Reg address:C2800000  
Console: switching to colour frame buffer device 80x30
fb0: s1d13xxx frame buffer device
Display 640 x 480 16Bpp
RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
physmap flash device: 200000 at 10000000
kmod: failed to exec /sbin/modprobe -s -k cfi_cmdset_0001, errno = 2
Support for command set 0001 not present
gen_probe: No supported Vendor Command Set found
Search for id:(89 17) interleave(1) type(2)
Search for id:(89 17) interleave(1) type(2)
Search for id:(89 17) interleave(1) type(2)
Search for id:(89 17) interleave(2) type(1)
Search for id:(89 17) interleave(2) type(1)
Search for id:(89 17) interleave(2) type(1)
Search for id:(89 00) interleave(2) type(2)
Search for id:(89 00) interleave(2) type(2)
Search for id:(89 00) interleave(2) type(2)
JEDEC: Found no Physically mapped flash device at location zero
kmod: failed to exec /sbin/modprobe -s -k map_rom, errno = 2
usb.c: registered new driver hub
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[e-mail]>
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
ttyS%d0 at MEM 0xfefff200 (irq = 1) is a AT91_SERIAL
ttyS%d1 at MEM 0xfefc4000 (irq = 7) is a AT91_SERIAL
eth0: Link now 100-FullDuplex
eth0: AT91 ethernet at 0xfefbc000 int=24 100-FullDuplex (00:00:00:00:ff:01)
AT91 Watchdog Timer enabled (5 seconds)
AT91 Real Time Clock driver
usb-ohci.c: USB OHCI at membase 0xc2948000, IRQ 23
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
i2c-dev.o: Registered 'AT91RM9200' as minor 0
Found AT91 i2c
AT91 SPI driver loaded
SmartMedia card inserted.
No NAND device found!!!
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 5859K
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing init memory: 72K
INIT: version 2.74 booting
mount: mount point /dev/pts does not exist
INIT: Entering runlevel: 3
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-110)
Starting system logger:  syslogdhub.c: USB new device connect on bus1/2, assigned device number 4
usb.c: USB device not accepting new address=4 (error=-110)
hub.c: USB new device connect on bus1/2, assigned device number 5
usb.c: USB device not accepting new address=5 (error=-110)

Starting interfaces eth0: Link now 100-FullDuplex

Starting INET services:  inetd
Starting mouse 
Starting tty 
Starting console mouse services: (no mouse is configured)
Starting httpd:  httpd
INIT: Id "1" respawning too fast: disabled for 5 minutes

AT91RM9200DK login: