syslib.c

还是嵌入式开发方面的

* Not applicable for the 860Ads
*
* RETURNS: ERROR, always.
*
* SEE ALSO: sysBusToLocalAdrs()
*/
 
STATUS sysLocalToBusAdrs
    (
    int 	adrsSpace,	/* bus address space where busAdrs resides */
    char *	localAdrs,	/* local address to convert */ 
    char **	pBusAdrs	/* where to return bus address */ 
    )
    {
    return (ERROR);
    }

/******************************************************************************
*
* sysBusToLocalAdrs - convert a bus address to a local address
*
* This routine gets the local address that accesses a specified VMEbus
* physical memory address.
*
* Not applicable for the 860Ads
*
* RETURNS: ERROR, always.
*
* SEE ALSO: sysLocalToBusAdrs()
*/

STATUS sysBusToLocalAdrs
    (
     int  	adrsSpace, 	/* bus address space where busAdrs resides */
     char *	busAdrs,   	/* bus address to convert */
     char **	pLocalAdrs 	/* where to return local address */
    )
    {
    return (ERROR);
    }

/******************************************************************************
*
* sysBusTas - test and set a location across the bus
*
* This routine does an atomic test-and-set operation across the backplane.
*
* Not applicable for the 860Ads.
*
* RETURNS: FALSE, always.
*
* SEE ALSO: vxTas()
*/

BOOL sysBusTas
    (
     char *	adrs		/* address to be tested-and-set */
    )
    {
    return (FALSE);
    }

/******************************************************************************
*
* sysBusClearTas - test and clear 
*
* This routine is a null function.
*
* RETURNS: N/A
*/

void sysBusClearTas
    (
     volatile char * address	/* address to be tested-and-cleared */
    )
    {
    } 

/*******************************************************************************
*
* sysCpmEnetDisable - disable the Ethernet controller
*
* This routine is expected to perform any target specific functions required
* to disable the Ethernet controller.  This usually involves disabling the
* Transmit Enable (TENA) signal.
*
* RETURNS: N/A
*/

void sysCpmEnetDisable
    (
    int         unit    /* not used - only slave SCC1 is wired to port */
    )
    {

	*PBPAR(vxImmrGet()) &= ~(0x1000);    /* set port B -> RTS1 = *TENA */
    
}

/*******************************************************************************
*
* sysCpmEnetIntDisable - disable the Ethernet interface interrupt
*
* This routine disable the interrupt for the Ethernet interface specified
* by <unit>.
*
* RETURNS: N/A.
*/

void sysCpmEnetIntDisable
    (
    int		unit
    )
    {
    /* If running an 823, use SCC2 */
/*    if (((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_823DB_MASK) ||
	((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_850DB_MASK))
	{
	*CIMR(vxImmrGet()) &= ~CIMR_SCC2;
	}
    else*/
	*CIMR(vxImmrGet()) &= ~CIMR_SCC1;
}



/*******************************************************************************
*
* sysCpmEnetEnable - enable the Ethernet controller
*
* This routine is expected to perform any target specific functions required
* to enable the Ethernet controller.  These functions typically include
* enabling the Transmit Enable signal (TENA) and connecting the transmit
* and receive clocks to the SCC.
*
* RETURNS: OK, or ERROR if the Ethernet controller cannot be enabled.
*/

STATUS sysCpmEnetEnable
    (
    int		unit    /* not used - only slave SCC1 is wired to port */
    )
    {
    int immrVal = vxImmrGet();

    /* If running an 823, use SCC2 */ 
/*    if (((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_823DB_MASK) ||
	((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_850DB_MASK))
	{
	*PAPAR(immrVal) |= 0x030c;
	*PADIR(immrVal) &= ~(0x030c);

	*PCPAR(immrVal) &= ~(0x00c0);
	*PCDIR(immrVal) &= ~(0x00c0);
	*PCSO(immrVal)  |= 0x00c0;

	*BCSR4 &= ~(BCSR4_ETHLOOP | BCSR4_TFPLDL_L | BCSR4_TPSQEL_L | 
		    BCSR4_MODEM_EN_L | BCSR4_DATA_VOICE_L);

	*SICR(immrVal)  |= 0x2c00;
	*SICR(immrVal)  &= ~(0x4000);	

	*BCSR1 &= ~(BCSR1_ETHN_EN_L);	

	*PBPAR(immrVal) |= 0x00002000;  
	*PBDIR(immrVal) |= 0x00002000; 
	}

    else
	{*/
	*PAPAR(immrVal) |= 0x0a03;
	*PADIR(immrVal) &= ~(0x0a03);

	*PCPAR(immrVal) &= ~(0x0030);
	*PCDIR(immrVal) &= ~(0x0030);
	*PCSO(immrVal)  |= 0x0030;

	*PCDIR(immrVal) |= 0x0f00;
	*PCDAT(immrVal) |= 0x0600;
	*PCDAT(immrVal) &= ~(0x0900);

	*SICR(immrVal)  |= 0x2F;            /* connect SCC1 clocks */
	*SICR(immrVal)  &= ~(0x40);         /* NMSI mode */
/*
	*BCSR1 &= ~(BCSR1_ETHN_EN_L);    */   /* enable Ethernet */

	*PBPAR(immrVal) |= 0x00001000;      /* set port B -> *RTS1 = TENA */
	*PBDIR(immrVal) |= 0x00001000;
	/*}*/


    return (OK);
    }

/*******************************************************************************
*
* sysCpmEnetAddrGet - get the hardware Ethernet address
*
* This routine provides the six byte Ethernet hardware address that will be
* used by each individual Ethernet device unit.  This routine must copy
* the six byte address to the space provided by <addr>.
*
* RETURNS: OK, or ERROR if the Ethernet address cannot be returned.
*/

STATUS sysCpmEnetAddrGet
    (
    int		unit,   /* not used - only slave SCC1 is wired to port */
    UINT8 *	addr
    )
    {
    bcopy ((char *) sysCpmEnetAddr, (char *) addr, sizeof (sysCpmEnetAddr));

    return (OK);
    }

/*******************************************************************************
*
* sysCpmEnetCommand - issue a command to the Ethernet interface controller
*
* RETURNS: OK, or ERROR if the Ethernet controller could not be restarted.
*/

STATUS sysCpmEnetCommand
    (
    int		unit,
    UINT16	command
    )
    {
    int	immrVal = vxImmrGet();

    /* If running an 823, use SCC2 */
/*    if (((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_823DB_MASK) ||
	((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_850DB_MASK))
	{
	while (*CPCR(immrVal) & CPM_CR_FLG); 
	*CPCR(immrVal) = CPM_CR_CHANNEL_SCC2 | command | CPM_CR_FLG;
	while (*CPCR(immrVal) & CPM_CR_FLG);
	}

    else
	{*/
	while (*CPCR(immrVal) & CPM_CR_FLG);
	*CPCR(immrVal) = CPM_CR_CHANNEL_SCC1 | command | CPM_CR_FLG;
	while (*CPCR(immrVal) & CPM_CR_FLG);
	/*}*/

    return (OK);
    }

/*******************************************************************************
*
* sysCpmEnetIntEnable - enable the Ethernet interface interrupt
*
* This routine enable the interrupt for the Ethernet interface specified
* by <unit>.
*
* RETURNS: N/A.
*/

void sysCpmEnetIntEnable
    (
    int		unit
    )
    {

    /* If running an 823, use SCC2 */
/*    if (((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_823DB_MASK) ||
	((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_850DB_MASK))
	{
	*CIMR(vxImmrGet()) |= CIMR_SCC2;
	}

    else*/
	*CIMR(vxImmrGet()) |= CIMR_SCC1;

    }

/*******************************************************************************
*
* sysCpmEnetIntClear - clear the Ethernet interface interrupt
*
* This routine clears the interrupt for the Ethernet interface specified
* by <unit>.
*
* RETURNS: N/A.
*/

void sysCpmEnetIntClear
    (
    int		unit
    )
    {

    /* If running an 823, use SCC2 */
/*    if (((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_823DB_MASK) ||
	((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_850DB_MASK))
	{
	*CISR(vxImmrGet()) = CISR_SCC2;
	}

    else*/
	*CISR(vxImmrGet()) = CISR_SCC1;
    }

/*******************************************************************************
*
* sysCpmAttach - attach wrapper
*
*/

STATUS sysCpmAttach
    (
    int         unit,           /* unit number */
    SCC *       pScc,           /* address of SCC parameter RAM */
    SCC_REG *   pSccReg,        /* address of SCC registers */
    VOIDFUNCPTR * ivec,         /* interrupt vector offset */
    SCC_BUF *   txBdBase,       /* transmit buffer descriptor base address */
    SCC_BUF *   rxBdBase,       /* receive buffer descriptor base address */
    int         txBdNum,        /* number of transmit buffer descriptors */
    int         rxBdNum,        /* number of receive buffer descriptors */
    UINT8 *     bufBase         /* address of memory pool; NONE = malloc it */
    )
	    {

    /* If running an 823, use SCC2 */
/*    if (((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_823DB_MASK) ||
	((*BCSR3 & BCSR3_DBID_MASK) == BCSR3_850DB_MASK))
	{
	return (cpmattach(unit, IF_USR_823ARG1, IF_USR_823ARG2, IF_USR_823ARG3,
			  txBdBase, rxBdBase, txBdNum, rxBdNum, bufBase));
	}*/

    /* else use SCC1 */
/*    else*/
/*
	return (cpmattach(unit, pScc, pSccReg, ivec, 
			  txBdBase, rxBdBase, txBdNum, rxBdNum, bufBase));
*/
	return (ERROR);			  
    }




#ifdef INCLUDE_MOT_FEC

/*******************************************************************************
*
* sysFecEnetEnable - enable the MII interface of the Fast Ethernet controller
*
* This routine is expected to perform any target specific functions required
* to enable the Ethernet device and the MII interface of the Fast Ethernet 
* controller. These functions include setting the MII-compliant signals on 
* Port D and disabling the IRQ7 signal.
*
* This routine does not enable the 7-wire serial interface.
*
* RETURNS: OK, or ERROR if the Fast Ethernet controller cannot be enabled.
*/

STATUS sysFecEnetEnable
    (
    UINT32	motCpmAddr	/* base address of the on-chip RAM */
    )
    {
    int intLevel = intLock();

    /* enable the Ethernet device for the FEC */

    /*
    *BCSR4 |= (BCSR4_FETH_RST | BCSR4_FETH_CFG0 
	       | BCSR4_FETH_FDE); 
    *BCSR4 &= ~BCSR4_UUFDIS;	*/	

    /* introduce a little delay */

    taskDelay (sysClkRateGet ());

    /* mask IRQ7 off, as it is shared with MII_TX_CLK */

    *SIMASK (motCpmAddr) &= ~SIMASK_IRM7;

    /* also clear any pending interrupt */

    *SIPEND (motCpmAddr) |= SIPEND_IRQ7;

    /* 
     * set the arbitration level for the FEC. Do not enable
     * FEC aggressive mode.
     */

    *SDCR (motCpmAddr) |= SDCR_FAID_BR6;

    /* set Port D to use MII signals */

    *PDPAR (motCpmAddr) = 0x1fff;
    *PDDIR (motCpmAddr) = 0x1c58;

    intUnlock (intLevel);

    return (OK);
    }

/*******************************************************************************
*
* sysFecEnetDisable - disable MII interface to the Fast Ethernet controller
*
* This routine is expected to perform any target specific functions required
* to disable the Ethernet device and the MII interface to the Fast Ethernet 
* controller.  This involves restoring the default values for all the Port 
* D signals.
*
* RETURNS: OK, always.
*/

STATUS sysFecEnetDisable
    (
    UINT32	motCpmAddr	/* base address of the on-chip RAM */
    )
    {
    int intLevel = intLock();

    /* disable the Ethernet device for the FEC */

  /*  *BCSR4 |= BCSR4_UUFDIS;*/

    /* configure all Port D pins as general purpose input pins */

    *PDPAR (motCpmAddr) = 0x0;
    *PDDIR (motCpmAddr) = 0x0;

    intUnlock (intLevel);

    return (OK);
    }

/*******************************************************************************
*
* sysFecEnetAddrGet - get the hardware Ethernet address
*
* This routine provides the six byte Ethernet hardware address that will be
* used by each individual Fast Ethernet device unit.  This routine must copy
* the six byte address to the space provided by <addr>.
*
* RETURNS: OK, or ERROR if the Ethernet address cannot be returned.
*/

STATUS sysFecEnetAddrGet
    (
    UINT32	motCpmAddr,	/* base address of the on-chip RAM */
    UCHAR *	addr		/* where to copy the Ethernet address */
    )
    {
    bcopy ((char *) sysFecEnetAddr, (char *) addr, sizeof (sysFecEnetAddr));

    return (OK);
    }

#endif /* INCLUDE_MOT_FEC */