📄 susgy.h
字号:
/* Copyright (c) Colorado School of Mines, 1997.*/
/* All rights reserved. */
/* susgy.h - include file for SEGY traces
* Reference:
* K. M. Barry, D. A. Cavers and C. W. Kneale, "Special Report:
* Recommended Standards for Digital Tape Formats",
* Geophysics, vol. 40, no. 2 (April 1975), P. 344-352.
*
* $Author: jkc $
* $Source: /usr/local/cwp/src/su/include/RCS/segy.h,v $
* $Revision: 1.20 $ ; $Date: 1996/02/20 16:41:29 $
*
* $Revised: Ni Yi in BGP --- May.12.1998
*/
/* TYPEDEFS */
typedef struct { /* segy - trace identification header */
int tracl; /* trace sequence number within line */
int tracr; /* trace sequence number within reel */
int fldr; /* field record number */
int tracf; /* trace number within field record */
int ep; /* energy source point number */
int cdp; /* CDP ensemble number */
int cdpt; /* trace number within CDP ensemble */
short trid; /* trace identification code:
1 = seismic data
2 = dead
3 = dummy
4 = time break
5 = uphole
6 = sweep
7 = timing
8 = water break
9---, N = optional use (N = 32,767)
Following are CWP id flags:
9 = autocorrelation
10 = Fourier transformed - no packing
xr[0],xi[0], ..., xr[N-1],xi[N-1]
11 = Fourier transformed - unpacked Nyquist
xr[0],xi[0],...,xr[N/2],xi[N/2]
12 = Fourier transformed - packed Nyquist
even N:
xr[0],xr[N/2],xr[1],xi[1], ...,
xr[N/2 -1],xi[N/2 -1]
(note the exceptional second entry)
odd N:
xr[0],xr[(N-1)/2],xr[1],xi[1], ...,
xr[(N-1)/2 -1],xi[(N-1)/2 -1],xi[(N-1)/2]
(note the exceptional second & last entries)
13 = Complex signal in the time domain
xr[0],xi[0], ..., xr[N-1],xi[N-1]
14 = Fourier transformed - amplitude/phase
a[0],p[0], ..., a[N-1],p[N-1]
15 = Complex time signal - amplitude/phase
a[0],p[0], ..., a[N-1],p[N-1]
16 = Real part of complex trace from 0 to Nyquist
17 = Imag part of complex trace from 0 to Nyquist
18 = Amplitude of complex trace from 0 to Nyquist
19 = Phase of complex trace from 0 to Nyquist
21 = Wavenumber time domain (k-t)
22 = Wavenumber frequency (k-omega)
23 = Envelope of the complex time trace
24 = Phase of the complex time trace
25 = Frequency of the complex time trace
30 = Depth-Range (z-x) traces
101 = Seismic data packed to bytes (by supack1)
102 = Seismic data packed to 2 bytes (by supack2)
*/
short nvs; /* number of vertically summed traces (see vscode
in bhed structure) */
short nhs; /* number of horizontally summed traces (see vscode
in bhed structure) */
short duse; /* data use:
1 = production
2 = test */
int offset; /* distance from source point to receiver
group (negative if opposite to direction
in which the line was shot) */
int gelev; /* receiver group elevation from sea level
(above sea level is positive) */
int selev; /* source elevation from sea level
(above sea level is positive) */
int sdepth; /* source depth (positive) */
int gdel; /* datum elevation at receiver group */
int sdel; /* datum elevation at source */
int swdep; /* water depth at source */
int gwdep; /* water depth at receiver group */
short scalel; /* scale factor for previous 7 entries
with value plus or minus 10 to the
power 0, 1, 2, 3, or 4 (if positive,
multiply, if negative divide) */
short scalco; /* scale factor for next 4 entries
with value plus or minus 10 to the
power 0, 1, 2, 3, or 4 (if positive,
multiply, if negative divide) */
int sx; /* X source coordinate */
int sy; /* Y source coordinate */
int gx; /* X group coordinate */
int gy; /* Y group coordinate */
short counit; /* coordinate units code:
for previous four entries
1 = length (meters or feet)
2 = seconds of arc (in this case, the
X values are longitude and the Y values
are latitude, a positive value designates
the number of seconds east of Greenwich
or north of the equator */
short wevel; /* weathering velocity */
short swevel; /* subweathering velocity */
short sut; /* uphole time at source */
short gut; /* uphole time at receiver group */
short sstat; /* source static correction */
short gstat; /* group static correction */
short tstat; /* total static applied */
short laga; /* lag time A, time in ms between end of 240-
byte trace identification header and time
break, positive if time break occurs after
end of header, time break is defined as
the initiation pulse which maybe recorded
on an auxiliary trace or as otherwise
specified by the recording system */
short lagb; /* lag time B, time in ms between the time break
and the initiation time of the energy source,
may be positive or negative */
short delrt; /* delay recording time, time in ms between
initiation time of energy source and time
when recording of data samples begins
(for deep water work if recording does not
start at zero time) */
short muts; /* mute time--start */
short mute; /* mute time--end */
unsigned short ns; /* number of samples in this trace */
unsigned short dt; /* sample interval; in micro-seconds */
short gain; /* gain type of field instruments code:
1 = fixed
2 = binary
3 = floating point
4 ---- N = optional use */
short igc; /* instrument gain constant */
short igi; /* instrument early or initial gain */
short corr; /* correlated:
1 = no
2 = yes */
short sfs; /* sweep frequency at start */
short sfe; /* sweep frequency at end */
short slen; /* sweep length in ms */
short styp; /* sweep type code:
1 = linear
2 = cos-squared
3 = other */
short stas; /* sweep trace length at start in ms */
short stae; /* sweep trace length at end in ms */
short tatyp; /* taper type: 1=linear, 2=cos^2, 3=other */
short afilf; /* alias filter frequency if used */
short afils; /* alias filter slope */
short nofilf; /* notch filter frequency if used */
short nofils; /* notch filter slope */
short lcf; /* low cut frequency if used */
short hcf; /* high cut frequncy if used */
short lcs; /* low cut slope */
short hcs; /* high cut slope */
short year; /* year data recorded */
short day; /* day of year */
short hour; /* hour of day (24 hour clock) */
short minute; /* minute of hour */
short sec; /* second of minute */
short timbas; /* time basis code:
1 = local
2 = GMT
3 = other */
short trwf; /* trace weighting factor, defined as 1/2^N
volts for the least sigificant bit */
short grnors; /* geophone group number of roll switch
position one */
short grnofr; /* geophone group number of trace one within
original field record */
short grnlof; /* geophone group number of last trace within
original field record */
short gaps; /* gap size (total number of groups dropped) */
short otrav; /* overtravel taper code:
1 = down (or behind)
2 = up (or ahead) */
/* local assignments */
float d1; /* sample spacing for non-seismic data */
float f1; /* first sample location for non-seismic data */
float d2; /* sample spacing between traces */
float f2; /* first trace location */
float ungpow; /* negative of power used for dynamic
range compression */
float unscale; /* reciprocal of scaling factor to normalize
range */
int ntr; /* number of traces */
short mark; /* mark selected traces */
short unass[15]; /* unassigned--NOTE: last entry causes
a break in the word alignment, if we REALLY
want to maintain 240 bytes, the following
entry should be an odd number of short/UINT2
OR do the insertion above the "mark" keyword
entry */
} segy;
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -