emi_bw_rx.uc

开发Inetl IXP2400平台所必须的硬件诊断和测试程序。该软件包支持的功能包括CPU基本功能检测

/* emi_bw_rx.uc
 *
 * Brief:
 *
 *
 *---------------------------------------------------------------------------
 *                                                                      
 *                  I N T E L   P R O P R I E T A R Y                   
 *                                                                      
 *     COPYRIGHT (c)  2002 BY  INTEL  CORPORATION.  ALL RIGHTS          
 *     RESERVED.   NO  PART  OF THIS PROGRAM  OR  PUBLICATION  MAY      
 *     BE  REPRODUCED,   TRANSMITTED,   TRANSCRIBED,   STORED  IN  A    
 *     RETRIEVAL SYSTEM, OR TRANSLATED INTO ANY LANGUAGE OR COMPUTER    
 *     LANGUAGE IN ANY FORM OR BY ANY MEANS, ELECTRONIC, MECHANICAL,    
 *     MAGNETIC,  OPTICAL,  CHEMICAL, MANUAL, OR OTHERWISE,  WITHOUT    
 *     THE PRIOR WRITTEN PERMISSION OF :                                
 *                                                                      
 *                        INTEL  CORPORATION                            
 *                                                                     
 *                     2200 MISSION COLLEGE BLVD                        
 *                                                                      
 *               SANTA  CLARA,  CALIFORNIA  95052-8119                  
 *                                                                      
 *---------------------------------------------------------------------------
 *
 *
 *  system: IXDP2400
 *  subsystem: DIAG
 *  author: dalsraja, 30 October, 2002
 *  revisions: 
 * 
 * 
 * --------------------------------------------------------------------------
 */

#include "common_uc.h"

#define RX_SINGLE_PHY					MSF_SINGLE_PHY
#define RX_WIDTH						MSF_WIDTH_4x8
#define RX_ENABLE_MASK					0xF
#define RX_MODE							MSF_POS_UTOPIA
#define RX_ELEMENTSIZE					MSF_ELEMENTSIZE_128
#define RBUF_ELEM_COUNT					(1 << (7 - RX_ELEMENTSIZE))
#define RBUF_ADDR_SHF					(6 + RX_ELEMENTSIZE)
#define RX_ELEMENT_SIZE_BYTE			(1 << RBUF_ADDR_SHF)

#define RX_TRANSFER_THREAD				&$TransferReg00
#define RX_SIGNAL_THREAD				&rx_sig_thd

#define MESSAGING_ADDR					0x1000
#define DRAM_PCKT_BASE					0x1000000

#define INTER_ME_SIG_NUM				15
#define SIG_THD_NUM						0

#define ME_0							0
#define ME_1							1
#define ME_2							2
#define ME_3							3

.reg cur_me
.reg $TransferReg00 $TransferReg01
.reg RxThreadList bytecnt elem error expected_sequence mask
.reg RxConfigData $RxConfigData0 RxConfigData0
.reg rbuf
.reg MsfAddress Thd_Freelist_Addr Rbuf_Elem_Done
.reg dramPacketBase 
.reg $rbuf_data0 $rbuf_data1
.reg $failure_type $scratch_data
.sig msf_sig sig_dram_xfer1
.sig rx_sig_thd inter_me_sig
.xfer_order $TransferReg00 $TransferReg01
.xfer_order $rbuf_data0 $rbuf_data1
.xfer_order $failure_type $scratch_data

.addr inter_me_sig INTER_ME_SIG_NUM

.set $TransferReg00
.set_sig inter_me_sig

br=ctx[0, Init_Value#]
ctx_arb[kill]

Init_Value#:
.begin
	.reg temp
	local_csr_rd[ACTIVE_CTX_STS]
	immed[temp, 0]
	alu[cur_me, 0x1F, AND, temp, >>3]	// Extract the current ME number
.end

.if (cur_me == 0)
	immed[Thd_Freelist_Addr, RX_THREAD_FREELIST_0]
.elif (cur_me == 1)
	immed[Thd_Freelist_Addr, RX_THREAD_FREELIST_1]
.elif (cur_me == 2)
	immed[Thd_Freelist_Addr, RX_THREAD_FREELIST_2]
.else
	immed[Thd_Freelist_Addr, RX_THREAD_FREELIST_3]
.endif

	immed[Rbuf_Elem_Done, RBUF_ELEMENT_DONE]
	immed[rbuf, RBUF_TBUF]
	immed[RxThreadList, ((RX_SIGNAL_THREAD << 12) | (0 << 4))]
	alu[RxThreadList, RxThreadList, OR, cur_me, <<7]
	alu[RxConfigData, RxThreadList, OR, RX_TRANSFER_THREAD]
	alu[RxConfigData, --,  B, RxConfigData, <<16]
	immed[expected_sequence, 0]
	immed[mask, MASK_4BIT]
	
	alu[--, cur_me, -, 0]
	beq[init_msf#]
	ctx_arb[inter_me_sig]
	br[ReceivePacket#]


init_msf#:
//****************************************************
// Configure RX/TX Control
//****************************************************
	immed[RxConfigData0, ((0<<9) | (RX_ELEMENTSIZE << 2))]
	immed_w1[RxConfigData0, ((RX_MODE << 6) | (RX_WIDTH << 4) | (RX_SINGLE_PHY << 3) | (0<<1)|(0<<0))]
	alu[$RxConfigData0, --, B, RxConfigData0]
	immed[MsfAddress, MSF_RX_CONTROL]
	msf[write, $RxConfigData0, MsfAddress, 0, 1], ctx_swap[msf_sig]


//******************************************************
// Initialize RBUF Freelist to add elements to the list
//******************************************************
.begin
	.reg temp_reg temp

	immed[temp_reg, 0]

init_RBUF#:
	alu[temp, --, B, temp_reg, <<16]
	msf[fast_wr, --, temp, RBUF_ELEMENT_DONE]
	alu[temp_reg, temp_reg, +, 1]
	alu[--, RBUF_ELEM_COUNT, -, temp_reg]
	bne[init_RBUF#]
.end


//******************************************************
// Configure RX UP Control CSRs 
//******************************************************
.begin
	.reg RxUPControl0

	immed[RxUPControl0, (UP_CTRL_PP_MODE | UP_CTRL_CP_MODE | UP_CTRL_PARITY | UP_CTRL_CELLSIZE | UP_CTRL_DRTIME)]
	alu[$RxConfigData0, --, B, RxUPControl0]
	immed[MsfAddress, RX_UP_CONTROL_0]
	msf[write, $RxConfigData0, MsfAddress, 0, 1], ctx_swap[msf_sig]
	immed[MsfAddress, RX_UP_CONTROL_1]
	msf[write, $RxConfigData0, MsfAddress, 0, 1], ctx_swap[msf_sig]
	immed[MsfAddress, RX_UP_CONTROL_2]
	msf[write, $RxConfigData0, MsfAddress, 0, 1], ctx_swap[msf_sig]
	immed[MsfAddress, RX_UP_CONTROL_3]
	msf[write, $RxConfigData0, MsfAddress, 0, 1], ctx_swap[msf_sig]
.end


//****************************************************
// Configure RX/TX Control
//****************************************************
	immed[RxConfigData0, ((0<<9) | (RX_ELEMENTSIZE << 2))]
	immed_w1[RxConfigData0, ((RX_ENABLE_MASK << 12) | (RX_MODE << 6) | (RX_WIDTH << 4) | (RX_SINGLE_PHY << 3) | (0<<1)|(0<<0))]
	alu[$RxConfigData0, --, B, RxConfigData0]
	immed[MsfAddress, MSF_RX_CONTROL]
	msf[write, $RxConfigData0, MsfAddress, 0, 1], ctx_swap[msf_sig]


.begin
	.reg temp
	immed[temp, ((ME_1 << 7) | (SIG_THD_NUM << 4) | (INTER_ME_SIG_NUM << 0))]
	alu[--, --, B, temp]
	cap[fast_wr, ALU, interthread_sig]
	immed[temp, ((ME_2 << 7) | (SIG_THD_NUM << 4) | (INTER_ME_SIG_NUM << 0))]
	alu[--, --, B, temp]
	cap[fast_wr, ALU, interthread_sig]
	immed[temp, ((ME_3 << 7) | (SIG_THD_NUM << 4) | (INTER_ME_SIG_NUM << 0))]
	alu[--, --, B, temp]
	cap[fast_wr, ALU, interthread_sig]
.end


//********************************************************
// Start of Test	
//********************************************************
ReceivePacket#:
	.set_sig rx_sig_thd
	msf[fast_wr, --, Thd_Freelist_Addr, RxConfigData] // add thread to freelist
	ctx_arb[rx_sig_thd]
	

// RSW should be in xfer register
// Transfer RBUF data to sram_in transfer registers
//***************************************
// Extract RSW
//****************************************
RSW#:
	alu[elem, --, B, $TransferReg00, >>24]	// Get element number
	alu[bytecnt, 0xFF, AND, $TransferReg00, >>16]	// Extract byte count
	alu[error, 0xF, AND, $TransferReg00, >>10]	// Extract error information
	.if (error > 0)
		immed[$failure_type, RECEIVE_ERROR]
		alu[$scratch_data, --, B, $TransferReg00]
		br[rbuf_to_dram#]
	.endif
	

//*************************************
// Transfer from RBUF to xfer register
//*************************************
no_error#:
.begin
	.reg rbuf_addr

	alu[rbuf_addr, rbuf, OR, elem, <<7]
	msf[read, $rbuf_data0, rbuf_addr, 0, 1], ctx_swap[msf_sig]
.end

.begin
	.reg cur_sequence temp
	alu[cur_sequence, --, B, $rbuf_data0, >>24]
	alu[--, expected_sequence, -, cur_sequence]
	beq[sequence_good#]
	immed[$failure_type, SEQUENCE_ERROR]
	alu[$scratch_data, expected_sequence, OR, cur_sequence, <<16]
//	alu[$scratch_data, --, B, $rbuf_data0]
.end


rbuf_to_dram#:
//*********************************
// Transfer from RBUF to DRAM
//*********************************	
.begin
	.reg pkt_buff_addr rel refcnt temp dramPacketBase

	immed[dramPacketBase, (DRAM_PCKT_BASE & MASK_16BIT)]
	immed_w1[dramPacketBase, ((DRAM_PCKT_BASE >> 16) & MASK_16BIT)]

	alu[refcnt, --, B, bytecnt, >>3]
	alu[--, bytecnt, AND, 0x7]
	beq[cont1#]
	alu[refcnt, refcnt, +, 1]
	alu[refcnt, refcnt, OR, 1, <<4]		// Set the overwrite bit for refcnt

cont1#:
	alu[temp, rbuf, OR, elem, <<7]		// 128B
	alu[temp, 16, OR, temp, <<5]		// shift rbuf addr and set the overwrite bit
	alu[temp, temp, OR, refcnt, <<21]	// shift refcnt and add for indirect ref

	dram[rbuf_rd, --, dramPacketBase, 0, 8], indirect_ref, sig_done[sig_dram_xfer1]

	ctx_arb[sig_dram_xfer1]
.end

	br[error_handling#]


//**************************************************************
//  Free up Element by writing to RBUF_Element_Done
//**************************************************************
sequence_good#:
.begin
	.reg temp
	alu[temp, --, B, elem, <<16]
	msf[fast_wr, --, temp, RBUF_ELEMENT_DONE]
.end

	alu[expected_sequence, expected_sequence, +, 1]
	alu[expected_sequence, mask, AND, expected_sequence]

	br[ReceivePacket#]


//**************************************************************
//  If an error occurs, write to XScale to indicate failure
//**************************************************************
error_handling#:
.begin
	.reg scratch_addr
	.sig scratch_sig

	immed[scratch_addr, MESSAGING_ADDR]
	scratch[write, $failure_type, scratch_addr, 0, 2], ctx_swap[scratch_sig]
.end

	ctx_arb[kill]