hal_diag.c

基于ecos的redboot

/*=============================================================================
//
//      hal_diag.c
//
//      HAL diagnostic output code
//
//=============================================================================
//####COPYRIGHTBEGIN####
//                                                                          
// -------------------------------------------                              
// The contents of this file are subject to the Red Hat eCos Public License 
// Version 1.1 (the "License"); you may not use this file except in         
// compliance with the License.  You may obtain a copy of the License at    
// http://www.redhat.com/                                                   
//                                                                          
// Software distributed under the License is distributed on an "AS IS"      
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the 
// License for the specific language governing rights and limitations under 
// the License.                                                             
//                                                                          
// The Original Code is eCos - Embedded Configurable Operating System,      
// released September 30, 1998.                                             
//                                                                          
// The Initial Developer of the Original Code is Red Hat.                   
// Portions created by Red Hat are                                          
// Copyright (C) 1998, 1999, 2000 Red Hat, Inc.                             
// All Rights Reserved.                                                     
// -------------------------------------------                              
//                                                                          
//####COPYRIGHTEND####
//=============================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):   lagarwal
// Contributors:
// Date:        2002-04-03
// Purpose:     HAL diagnostic output
// Description: Implementations of HAL diagnostic output support.
//
//####DESCRIPTIONEND####
//
//===========================================================================*/

#include <pkgconf/hal.h>
#include <pkgconf/system.h>
#include CYGBLD_HAL_PLATFORM_H

#include <cyg/infra/cyg_type.h>         // base types
#include <cyg/infra/cyg_trac.h>         // tracing macros
#include <cyg/infra/cyg_ass.h>          // assertion macros

#include <cyg/hal/hal_arch.h>           // basic machine info
#include <cyg/hal/hal_intr.h>           // interrupt macros
#include <cyg/hal/hal_io.h>             // IO macros
#include <cyg/hal/hal_if.h>             // calling interface API
#include <cyg/hal/hal_misc.h>           // helper functions
#include <cyg/hal/hal_diag.h>
#include <cyg/hal/hal_ixdp2400.h>        // Hardware definitions
#include <cyg/hal/drv_api.h>            // cyg_drv_interrupt_acknowledge

externC cyg_uint32 ext_osc_freq;

static void cyg_hal_plf_serial_init(void);

void
cyg_hal_plf_comms_init(void)
{
    static int initialized = 0;

    if (initialized)
        return;

    initialized = 1;

    cyg_hal_plf_serial_init();
//    cyg_hal_plf_lcd_init();
}

//=============================================================================
// Serial driver
//=============================================================================

//-----------------------------------------------------------------------------
// There is one serial port
#define CYG_DEV_SERIAL_BASE_A    0xC0030000 // port A

//-----------------------------------------------------------------------------
// Define the serial registers.
#define CYG_DEV_SERIAL_RBR   0x00  // receiver buffer register, read, dlab = 0
#define CYG_DEV_SERIAL_THR   0x00 // transmitter holding register, write, dlab = 0
#define CYG_DEV_SERIAL_DLL   0x00 // divisor latch (LS), read/write, dlab = 1
#define CYG_DEV_SERIAL_IER   0x04 // interrupt enable register, read/write, dlab = 0
#define CYG_DEV_SERIAL_DLM   0x04 // divisor latch (MS), read/write, dlab = 1
#define CYG_DEV_SERIAL_IIR   0x08 // interrupt identification register, read, dlab = 0
#define CYG_DEV_SERIAL_FCR   0x08 // fifo control register, write, dlab = 0
#define CYG_DEV_SERIAL_LCR   0x0C // line control register, write
#define CYG_DEV_SERIAL_LSR   0x14 // line status register, read
#define CYG_DEV_SERIAL_SCR   0x1C // scratch pad register

// The interrupt enable register bits.
#define SIO_IER_ERDAI   0x01            // enable received data available irq
#define SIO_IER_ETHREI  0x02            // enable THR empty interrupt
#define SIO_IER_ELSI    0x04            // enable receiver line status irq
#define SIO_IER_RTOIE	0x10			// enable receive timeout int.
#define SIO_IER_UUE		0x40			// enable uart unit

// The interrupt identification register bits.
#define SIO_IIR_IP      0x01            // 0 if interrupt pending
#define SIO_IIR_ID_MASK 0x0e            // mask for interrupt ID bits
#define ISR_Tx  0x02
#define ISR_Rx  0x04

// The line status register bits.
#define SIO_LSR_DR      0x01            // data ready
#define SIO_LSR_OE      0x02            // overrun error
#define SIO_LSR_PE      0x04            // parity error
#define SIO_LSR_FE      0x08            // framing error
#define SIO_LSR_BI      0x10            // break interrupt
#define SIO_LSR_THRE    0x20            // transmitter holding register empty
#define SIO_LSR_TEMT    0x40            // transmitter register empty
#define SIO_LSR_ERR     0x80            // any error condition

// The line control register bits.
#define SIO_LCR_WLS0   0x01             // word length select bit 0
#define SIO_LCR_WLS1   0x02             // word length select bit 1
#define SIO_LCR_STB    0x04             // number of stop bits
#define SIO_LCR_PEN    0x08             // parity enable
#define SIO_LCR_EPS    0x10             // even parity select
#define SIO_LCR_SP     0x20             // stick parity
#define SIO_LCR_SB     0x40             // set break
#define SIO_LCR_DLAB   0x80             // divisor latch access bit

// The FIFO control register
#define SIO_FCR_FCR0   0x01             // enable xmit and rcvr fifos
#define SIO_FCR_FCR1   0x02             // clear RCVR FIFO
#define SIO_FCR_FCR2   0x04             // clear XMIT FIFO


//-----------------------------------------------------------------------------
typedef struct {
    cyg_uint8* base;
    cyg_int32 msec_timeout;
    int isr_vector;
} channel_data_t;

//-----------------------------------------------------------------------------
static void
init_serial_channel(const channel_data_t* __ch_data)
{
    cyg_uint8* base = __ch_data->base;
    cyg_uint8 lcr;
	unsigned int baudrate, divisor;

	baudrate = DEFAULT_BAUD;

	// calculate the divisor based on ext. osc. clock
	divisor = (ext_osc_freq / 2) / (16 * baudrate);

    // 8-1-no parity.
    lcr = SIO_LCR_WLS0 | SIO_LCR_WLS1;

    lcr |= SIO_LCR_DLAB;
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_LCR, lcr);
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_DLL, divisor);
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_DLM, divisor >> 8);
    lcr &= ~SIO_LCR_DLAB;
	HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_LCR, lcr);
	HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_IER, 0x40);
    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_FCR, 0x07);  // Enable & clear FIFO
}

static cyg_bool
cyg_hal_plf_serial_getc_nonblock(void* __ch_data, cyg_uint8* ch)
{
    cyg_uint8* base = ((channel_data_t*)__ch_data)->base;
    cyg_uint8 lsr;

    HAL_READ_UINT8(base+CYG_DEV_SERIAL_LSR, lsr);
    if ((lsr & SIO_LSR_DR) == 0)
        return false;

    HAL_READ_UINT8(base+CYG_DEV_SERIAL_RBR, *ch);

    return true;
}


cyg_uint8
cyg_hal_plf_serial_getc(void* __ch_data)
{
    cyg_uint8 ch;
    CYGARC_HAL_SAVE_GP();

    while(!cyg_hal_plf_serial_getc_nonblock(__ch_data, &ch));

    CYGARC_HAL_RESTORE_GP();
    return ch;
}

void
cyg_hal_plf_serial_putc(void* __ch_data, cyg_uint8 c)
{
    cyg_uint8* base = ((channel_data_t*)__ch_data)->base;
    cyg_uint8 lsr;
    CYGARC_HAL_SAVE_GP();

    do {
        HAL_READ_UINT8(base+CYG_DEV_SERIAL_LSR, lsr);
    } while ((lsr & SIO_LSR_THRE) == 0);

    HAL_WRITE_UINT8(base+CYG_DEV_SERIAL_THR, c);

    CYGARC_HAL_RESTORE_GP();
}

static const channel_data_t channels[1] = {
    { (cyg_uint8*)CYG_DEV_SERIAL_BASE_A, 1000, CYGNUM_HAL_INTERRUPT_SERIAL},
};

static void
cyg_hal_plf_serial_write(void* __ch_data, const cyg_uint8* __buf, 
                         cyg_uint32 __len)
{
    CYGARC_HAL_SAVE_GP();

    while(__len-- > 0)
        cyg_hal_plf_serial_putc(__ch_data, *__buf++);

    CYGARC_HAL_RESTORE_GP();
}

static void
cyg_hal_plf_serial_read(void* __ch_data, cyg_uint8* __buf, cyg_uint32 __len)
{
    CYGARC_HAL_SAVE_GP();

    while(__len-- > 0)
        *__buf++ = cyg_hal_plf_serial_getc(__ch_data);

    CYGARC_HAL_RESTORE_GP();
}

cyg_bool
cyg_hal_plf_serial_getc_timeout(void* __ch_data, cyg_uint8* ch)
{
    int delay_count;
    channel_data_t* chan = (channel_data_t*)__ch_data;
    cyg_bool res;
    CYGARC_HAL_SAVE_GP();

    delay_count = chan->msec_timeout * 10; // delay in .1 ms steps
    for(;;) {
        res = cyg_hal_plf_serial_getc_nonblock(__ch_data, ch);
        if (res || 0 == delay_count--)
            break;
        
        CYGACC_CALL_IF_DELAY_US(100);
    }

    CYGARC_HAL_RESTORE_GP();
    return res;
}

static int
cyg_hal_plf_serial_control(void *__ch_data, __comm_control_cmd_t __func, ...)
{
    static int irq_state = 0;
    channel_data_t* chan = (channel_data_t*)__ch_data;
    cyg_uint8 ier;
    int ret = 0;
    CYGARC_HAL_SAVE_GP();

    switch (__func) {
    case __COMMCTL_IRQ_ENABLE:
        HAL_INTERRUPT_UNMASK(chan->isr_vector);
        HAL_INTERRUPT_SET_LEVEL(chan->isr_vector, 1);
        HAL_READ_UINT8(chan->base+CYG_DEV_SERIAL_IER, ier);
        ier |= SIO_IER_ERDAI;
        HAL_WRITE_UINT8(chan->base+CYG_DEV_SERIAL_IER, ier);
        irq_state = 1;
        break;
    case __COMMCTL_IRQ_DISABLE:
        ret = irq_state;
        irq_state = 0;
        HAL_INTERRUPT_MASK(chan->isr_vector);