u_u_used_reg.h

U盘原代码,包括FAT16和USB的所有东东都是开放的,请认真看呀.

//加密字节
encrypt_byte_a			==	0X00//93//00//0xaa//00
encrypt_byte_b			==	0X00//93//00//0x11//00
encrypt_byte_c			==	0X00//93//00//0x55//00

BULK_STATE				== 	0X31
CONFIG		   	  	== 0X00
PACKET_SIZE_END   	== 0X01
OUT_USB_FIFO_FULL 	== 0X02
IN_USB_FIFO_FULL  	== 0X03		
MCU_512B_FULL	  	== 0X04
BEGIN_PUT_EP1_DATA	== 0X05
IMAGE_END	 	  	== 0X06
DataDownLoadSTART	  == 0X07
IMAGE_RESTART	  == 0X07

//U-DISK用
BULK_COUNT				==	0x32		;bulk最大传输64个字节计数
PAGE_COUNT				==	0x33		;一个BLOCK内的PAGE计数
TOTAL_COUNT1			==	0x34		;HOST要求传输的的总BLOCK数
TOTAL_COUNT2			==	0X35		
/*
TEMP0					==	0x36
TEMP1					== 	0X37
TEMP2					==	0X38
TEMP3					==	0x39
TEMP4					==	0x3A
*/
READY_COUNT				==	0x38

a2000_to_xp_flag		==	0x39
	in_the_TEST_UNIT_READY	==	1
	READY_FLAG				==	2

fast_skip				==	0x39
	skip_end		==	3
	skip_begin		==	4
	make_vol_to_zero	==5
	
X_POD_E_POD				==	0X39
	X_E_POD_change	==	6				;0->x-pod;1->e-pod	
	
MIX_COUNT_1				==	0x3a

TEMP5					==	0x3B
TEMP6					==	0x3C
//U-DISK用
ADD_BUF_COUNT			==	0x3D

////U-DISK用,读写次数寄存
;Parameter_List3_keep	==	0x3E
Parameter_List2_keep	==	0x3E//0X43
R0				==	0X40//0x44

R1				==	0X41//0x45
R2				==	0X42//0x46

R3				==	0X43//0x47
////U-DISK用,源地址寄存
SOURCE_ADD_1	==	0X44//0X48
SOURCE_ADD_2	==	0X45//0X49
SOURCE_ADD_3	==	0X46//0X4A
////U-DISK用,目标地址寄存
OBJECT_ADD_1	==	0X47//0X4B
OBJECT_ADD_2	==	0X48//0X4C
OBJECT_ADD_3	==	0X49//0X4D
//读写次数寄存
;Parameter_List1_keep	==	0x4E
;Parameter_List0_keep	==	0x4F

//U-DISK用,把一块分成ADD_X,ADD_Y,ADD_Z三部份
ADD_X			==	0X4A//0X58
ADD_Y			==	0X4B//0X59
ADD_Z			==	0X4C//0X5A
//U-DISK用,扇区地址寄存
ADD_TEMP1		==	0X4D//0X5B
ADD_TEMP2		==	0X4E//0X5C
ADD_TEMP3		==	0X4F//0X5D
//U-DISK用,缓冲区地址寄存
ADD_BUF1		==	0X55//0X5E
ADD_BUF2		==	0X56//0X5F
ADD_BUF3		==	0X57//0X60
ERASE_COUNT		==	0X5B
//BANK 5
/*
OLED_FONT_TEMP	==	0X80		// 32 BYTE THE FONT 80~9F
READ_COUNT		==	0x4E		
FONT_ADD		==	0X4F		
*/
//FLASH用
FlashWriteStatus	EQU		0X3F//0X3E
FlashRowAdd3        EQU     0x50    ;FLASH_ROM