fet140_uart01_0115k_2.s43

基于IAR Workbench for MSP430 的汇编语言例程

;******************************************************************************
;   MSP-FET430P140 Demo - USART0 UART 115200 Echo ISR, XT2 HF XTAL SMCLK 
;
;   Description; This program will echo a received character, RX interrupt 
;   service used. XT2 oscillator used in this example.
;   ACLK = MCLK = SMCLK = UCLK0 = XT2 = 8MHz
;   Baud rate divider with 8Mhz XTAL @115200 = 8MHz/115200 = 69.44(0045 2C)
;   //*An external 8MHz XTAL on X2IN X2OUT is required for ACLK*//	  
;
;                MSP430F149
;             -----------------
;         /|\|             X2IN|-  
;          | |                 | 8Mhz  
;          --|RST         X2OUT|-
;            |                 |
;            |             P3.4|------------>
;            |                 | 115200 - 8N1 
;            |             P3.5|<------------
;
;   M.Buccini
;   Texas Instruments, Inc
;   January 2004
;******************************************************************************
#include  "msp430x14x.h"
;------------------------------------------------------------------------------ 
            ORG     01100h                  ; Progam Start 
;------------------------------------------------------------------------------ 
RESET       mov.w   #0A00h,SP               ; Initialize 'F1x9 stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop WDT
SetupP3     bis.b   #030h,&P3SEL            ; P3.4,5 = USART0 TXD/RXD
SetupBC     bic.b   #XT2OFF,&BCSCTL1        ; XT2on
SetupOsc    bic.b   #OFIFG,&IFG1            ; Clear OSC fault flag 
            mov.w   #0FFh,R15               ; R15 = Delay 
SetupOsc1   dec.w   R15                     ; Additional delay to ensure start 
            jnz     SetupOsc1               ;
            bit.b   #OFIFG,&IFG1            ; OSC fault flag set? 
            jnz     SetupOsc                ; OSC Fault, clear flag again 
            bis.b   #SELM_2+SELS,BCSCTL2    ; MCLK = SMCLK = XT2
                                            ;
SetupUART0  bis.b   #UTXE0+URXE0,&ME1       ; Enable USART0 TXD/RXD
            bis.b   #CHAR,&UCTL0            ; 8-bit characters
            mov.b   #SSEL1,&UTCTL0          ; UCLK = SMCLK
            mov.b   #045h,&UBR00            ; 8Mhz/115200 - 69.44
            mov.b   #000h,&UBR10            ; 
            mov.b   #02Ch,&UMCTL0           ; Modulation
            bic.b   #SWRST,&UCTL0           ; **Initialize USART state machine**
            bis.b   #URXIE0,&IE1            ; Enable USART0 RX interrupt
                                            ;   
Mainloop    bis.b   #CPUOFF+GIE,SR          ; Enter LPM0, interrupts enabled
            nop                             ; Needed only for debugger
                                            ;
;------------------------------------------------------------------------------ 
USART0RX_ISR;  Echo back RXed character, confirm TX buffer is ready first
;------------------------------------------------------------------------------ 
TX1         bit.b   #UTXIFG0,&IFG1          ; USART1 TX buffer ready?
            jz      TX1                     ; Jump is TX buffer not ready
            mov.b   &RXBUF0,&TXBUF0         ; TX -> RXed character
            reti                            ; 
                                            ;
;------------------------------------------------------------------------------ 
;           Interrupt Vectors Used MSP430x13x/14x/15x/16x        
;------------------------------------------------------------------------------ 
            ORG     0FFFEh                  ; 
            DW      RESET                   ; POR, ext. Reset, Watchdog
            ORG     0FFF2h                  ; 
            DW      USART0RX_ISR            ; USART0 receive
            end