ser1cli.c

TDK 6521 SOC 芯片 DEMO程序

    len = cchRx;
    irq_enable ();    // critical section- find the buffer size in use

    return (len);
}
#pragma restore
#endif

#if PORT == 0
uint16_t Serial0_CRx (uint8x_t *buffer, uint16_t rxlen)
#elif PORT == 1
uint16_t Serial1_CRx (uint8x_t *buffer, uint16_t rxlen)
#else
#error unhandled port selection
#endif
{                                       // Here we assume (head = tail) => EMPTY
   if (rxlen > 0)
   {
        uint16_t len;

        irq_disable ();   // critical section- find the buffer size available
        len = (uint16_t) cchRx;
        irq_enable ();    // critical section- find the buffer size available

        rxlen = len = min (rxlen, len); // figure the size to be used

        while (len--)  // copy the data out
        {
            ichOutRx &= mbuf;
            *buffer++ = achRx[ ichOutRx++ ];
        }

        if (rxlen > 0)
        {
            irq_disable ();   // critical section- consume the buffer
            cchRx -= rxlen;

            if (xon_xoff_s && !rxs_flow)
            {                                // Maybe turn flow back ON.
                if (cchRx < sbf / 4) 
                    rxs_flow_on ();
            }
            irq_enable ();    // critical section- consume the buffer
        }
    }

    return rxlen;
}

#pragma save
#pragma NOAREGS
static void rxs_flow_on (void) small reentrant 
{
    rxs_flow = ON;                  // Turn flow ON.  
    txs = XON;                      // Send XON.

    if (S_EMPTY == txs_status)
    {
        txs_status = S_PENDING;
        stm_stop (free_cnt);
        free_cnt = NULL;
        ser_enable_xmit_rdy();
    }
}

static void rxs_flow_off (void) small reentrant 
{
    rxs_flow = OFF;                 // Turn flow OFF.   
    txs = XOFF;                     // Send XOFF.

    if (S_EMPTY == txs_status)
    {
        txs_status = S_PENDING;
        stm_stop (free_cnt);
        free_cnt = NULL;
        ser_enable_xmit_rdy();
    }
}

static void free_timer (void) small reentrant
{
    free_cnt = NULL;
    ser_xmit_free();  // free the transmitter for other uses
}
#pragma restore

#if ROM == 1
#if PORT == 0
void Serial0_RxFlowOn (void)
#elif PORT == 1
void Serial1_RxFlowOn (void)
#else
#error unhandled port selection
#endif
{
    irq_disable ();                     // Begin critical section.
    rxs_flow_on ();
    irq_enable ();                      // End critical section.
}
#endif

#if ROM == 1
#if PORT == 0
void Serial0_RxFlowOff (void)
#elif PORT == 1
void Serial1_RxFlowOff (void)
#else
#error unhandled port selection
#endif
{
    irq_disable ();                     // Begin critical section.
    rxs_flow_off ();
    irq_enable ();                      // End critical section.
}
#endif

#pragma save
#pragma NOAREGS
#if PORT == 0
void cli0_in (void) small reentrant
#elif PORT == 1
void cli1_in (void) small reentrant
#else
#error unhandled port selection
#endif
{
    static uint8_t data rx;

    rxs = ser_rcv();
    rx = rxs & 0x7F;

    if (xon_xoff_s && (XON == rx || XOFF == rx))
    {               
        switch (rx)
        {
            case XON:
                if (!txs_flow && (S_PENDING == txs_status))
                {                           // Restart XMT'r.
                    stm_stop (free_cnt);
                    free_cnt = NULL;
                    ser_enable_xmit_rdy();  
                }

                txs_flow = TRUE;
                break;

            case XOFF:
                txs_flow = FALSE;
                break;
        }
    }
    else if (cchRx < sbf)
    {
        ichInRx &= mbuf;
        achRx[ ichInRx++ ] = rxs;
        cchRx++;

        if (xon_xoff_s && ((rxs_flow && (sbf / 2 < cchRx)) || (cchRx > sbf - 4)))
            rxs_flow_off ();        // Turn flow off.
    }
}
#pragma restore
#pragma save

#pragma NOAREGS
#if PORT == 0
void cli0_out (void) small reentrant
#elif PORT == 1
void cli1_out (void) small reentrant
#else
#error unhandled port selection
#endif
{
    if (txs != '\0')
    {
        ser_xmit (txs);                   
        txs = '\0';     // Allows insertion of single flow control byte later.
    }
    else if (0 == cchTx)
    {
        txs_status = S_EMPTY;
        ser_disable_xmit_rdy();
        free_cnt = stm_start (milliseconds(7000), 0, free_timer);
    }
    else if (txs_flow)
    {
        ichOutTx &= mbuf;
        ser_xmit (achTx[ ichOutTx++ ]);
        cchTx--;
    }
    else
    {                                       // TX flow turned off..  
        ser_disable_xmit_rdy();             // ..probably via XOFF.
        free_cnt = stm_start (milliseconds(7000), 0, free_timer);
    }
}
#pragma restore

/***************************************************************************
 * $Log: ser1cli.c,v $
 * Revision 1.24  2006/09/27 00:54:24  tvander
 * Initialize low level driver after high level buffering is set up.
 *
 * Revision 1.23  2006/09/09 01:08:40  gmikef
 * *** empty log message ***
 *
 * Revision 1.22  2006/06/29 00:54:06  tvander
 * Minor fix to comments
 *
 * Revision 1.21  2006/06/23 20:46:05  tvander
 * Removed wait-for-io; it slowed response in brownout mode, and caused
 * hangs. The cure was definitely worse than the disease: a few clobbered characters after certain commands.
 *
 * Revision 1.20  2006/06/15 19:56:04  tvander
 * Fixed misc. serial errors.
 *
 * Revision 1.19  2006/06/06 03:53:52  tvander
 * Added calibration count to access.c
 * Added to help files, at least, they compile for a 6513.
 * io.c support the calibration loader.
 * ser0cli.c and ser1cli.c were allocating too many timers.  Fixed.
 *
 * Revision 1.18  2006/05/25 03:25:59  tvander
 * Some untested adjustments for calibration loader.
 * Added automatic enabling of UART2 and switching to pulse output on DIO2
 *
 * Revision 1.17  2006/04/28 22:24:05  tvander
 * Reverse ported defects fixed when these files were ported to the 3.05 code.
 *
 * Revision 1.16  2006/03/07 23:57:09  tvander
 * Revised help system for accuracy.
 * Revised help system for compile flags.
 * Clean build
 *
 * Revision 1.15  2006/03/06 03:29:14  Michael T. Fischer
 * More 6530 prep.
 *
 * Revision 1.14  2006/01/16 20:11:21  tvander
 * Clean Keil build, all versions
 *
 * Revision 1.13  2006/01/10 03:55:53  gmikef
 * Added PDATA support for CE Outputs.
 *
 * Revision 1.11  2005/12/07 01:36:53  tvander
 * Added conditionals to make Xoff/Xon flow controls present in ROM.
 *
 * Revision 1.10  2005/11/15 05:12:28  gmikef
 * Added Serial_RxFlowOn/Off publics.
 *
 * Revision 1.9  2005/11/09 01:39:58  tvander
 * Added fix for XON/XOFF, from ser0cli.c
 *
 * Revision 1.8  2005/11/04 03:16:52  gmikef
 * Enhanced XOFF (send out extra XOFF if necessary).
 * Enhanced help and download info.
 *
 * Revision 1.7  2005/11/03 19:18:32  tvander
 * Same logic, but ser1cli.c and ser0cli.c are the same code.
 *
 * Revision 1.7  2005/11/02 03:07:28  gmikef
 * Xon/Xoff flow control working.
 *
 * Revision 1.6  2005/10/18 02:17:08  tvander
 * Access CLI in brownout by pressing reset.
 * Debugged serial 1 usage from CLI.
 * Implemented scrolling display as M17
 *
 * Revision 1.5  2005/10/08 04:41:18  tvander
 * Fixed priority inversion.
 * Rewrote watchdog to work in brownout, but of course it doesn't work.
 * Watchdog can now be defeated by clearing watchdog option to 0.
 * Reorganized watt hour modules (at last!).
 * Disabled reading of STATUS in 6521_cli because the CE's status is always SAG.
 * Tested with 6521_CLI; measurements seem to work.
 * Fixed other builds.
 *
 * Revision 1.4  2005/09/12 07:47:28  tvander
 * Power measurement is stable, with no creep.
 * VARh measurement is stable, with no creep.
 * Pulse sources work.
 * Full access to MPU variables.
 * Rolled date.
 * Clock software works.
 *
 * Revision 1.3  2005/09/08 00:31:40  tvander
 * Fixed: Lost data due to overwrite of Ithrshld, xfer busy never runs,
 * unavailable second phase, cosmetic issues with status.  Updated
 * date.
 *
 * Revision 1.2  2005/08/31 05:52:45  gmikef
 * First version w/ LAPIE interface.
 *
 * Revision 1.1  2005/08/28 02:25:41  gmikef
 * *** empty log message ***
 *
 * Revision 1.2  2005/08/20 01:32:45  gmikef
 * *** empty log message ***
 *
 * Revision 1.1  2005/08/19 01:06:52  gmikef
 * *** empty log message ***
 *
 * 2005 August 18; First Version. 
 * 
 * Copyright (C) 2005 Teridian Semiconductor Corp. All Rights Reserved.     *
 * this program is fully protected by the United States copyright          *
 * laws and is the property of Teridian Semiconductor Corporation.         *
 ***************************************************************************/
#endif /* SER0CLI.c */