yellowstone.c

来自「适合KS8695X」· C语言 代码 · 共 423 行 · 第 1/2 页

		if ((k & 1023) == 0) {
			printf("%3d MB\r", k / 1024);
		}

		memset(mem, 0xaaaaaaaa, 1024);
		for (n = 0; n < kend; ++n) {
			if (mem[n] != 0xaaaaaaaa) {
				printf("SDRAM test fails at: %08x\n",
				       (uint) & mem[n]);
				return 1;
			}
		}

		memset(mem, 0x55555555, 1024);
		for (n = 0; n < kend; ++n) {
			if (mem[n] != 0x55555555) {
				printf("SDRAM test fails at: %08x\n",
				       (uint) & mem[n]);
				return 1;
			}
		}
	}
	printf("SDRAM test passes\n");
	return 0;
}
#endif

/*************************************************************************
 *  pci_pre_init
 *
 *  This routine is called just prior to registering the hose and gives
 *  the board the opportunity to check things. Returning a value of zero
 *  indicates that things are bad & PCI initialization should be aborted.
 *
 *	Different boards may wish to customize the pci controller structure
 *	(add regions, override default access routines, etc) or perform
 *	certain pre-initialization actions.
 *
 ************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
int pci_pre_init(struct pci_controller *hose)
{
	unsigned long strap;
	unsigned long addr;

	/*--------------------------------------------------------------------------+
     *	Bamboo is always configured as the host & requires the
     *	PCI arbiter to be enabled.
	 *--------------------------------------------------------------------------*/
	mfsdr(sdr_sdstp1, strap);
	if ((strap & SDR0_SDSTP1_PAE_MASK) == 0) {
		printf("PCI: SDR0_STRP1[PAE] not set.\n");
		printf("PCI: Configuration aborted.\n");
		return 0;
	}

    /*-------------------------------------------------------------------------+
    | Set priority for all PLB3 devices to 0.
    | Set PLB3 arbiter to fair mode.
    +-------------------------------------------------------------------------*/
	mfsdr(sdr_amp1, addr);
	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
	addr = mfdcr(plb3_acr);
	mtdcr(plb3_acr, addr | 0x80000000);

    /*-------------------------------------------------------------------------+
    | Set priority for all PLB4 devices to 0.
    +-------------------------------------------------------------------------*/
	mfsdr(sdr_amp0, addr);
	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
	mtdcr(plb4_acr, addr);

    /*-------------------------------------------------------------------------+
    | Set Nebula PLB4 arbiter to fair mode.
    +-------------------------------------------------------------------------*/
	/*  Segment0 */
	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
	mtdcr(plb0_acr, addr);

	/* Segment1 */
	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
	mtdcr(plb1_acr, addr);

	return 1;
}
#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */

/*************************************************************************
 *  pci_target_init
 *
 *	The bootstrap configuration provides default settings for the pci
 *	inbound map (PIM). But the bootstrap config choices are limited and
 *	may not be sufficient for a given board.
 *
 ************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
	/*--------------------------------------------------------------------------+
	 * Set up Direct MMIO registers
	 *--------------------------------------------------------------------------*/
   /*--------------------------------------------------------------------------+
   | PowerPC440 EP PCI Master configuration.
   | Map one 1Gig range of PLB/processor addresses to PCI memory space.
   |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
   |   Use byte reversed out routines to handle endianess.
   | Make this region non-prefetchable.
   +--------------------------------------------------------------------------*/
	out32r(PCIX0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
	out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE);	/* PMM0 PCI Low Address */
	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
	out32r(PCIX0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */

	out32r(PCIX0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
	out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2);	/* PMM0 Local Address */
	out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
	out32r(PCIX0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */

	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
	out32r(PCIX0_PTM1LA, 0);	/* Local Addr. Reg */
	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */

	/*--------------------------------------------------------------------------+
	 * Set up Configuration registers
	 *--------------------------------------------------------------------------*/

	/* Program the board's subsystem id/vendor id */
	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
			      CFG_PCI_SUBSYS_VENDORID);
	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);

	/* Configure command register as bus master */
	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);

	/* 240nS PCI clock */
	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);

	/* No error reporting */
	pci_write_config_word(0, PCI_ERREN, 0);

	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);

}
#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */

/*************************************************************************
 *  pci_master_init
 *
 ************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
	unsigned short temp_short;

   /*--------------------------------------------------------------------------+
   | Write the PowerPC440 EP PCI Configuration regs.
   |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
   |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
   +--------------------------------------------------------------------------*/
	pci_read_config_word(0, PCI_COMMAND, &temp_short);
	pci_write_config_word(0, PCI_COMMAND,
			      temp_short | PCI_COMMAND_MASTER |
			      PCI_COMMAND_MEMORY);
}
#endif				/* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */

/*************************************************************************
 *  is_pci_host
 *
 *	This routine is called to determine if a pci scan should be
 *	performed. With various hardware environments (especially cPCI and
 *	PPMC) it's insufficient to depend on the state of the arbiter enable
 *	bit in the strap register, or generic host/adapter assumptions.
 *
 *	Rather than hard-code a bad assumption in the general 440 code, the
 *	440 pci code requires the board to decide at runtime.
 *
 *	Return 0 for adapter mode, non-zero for host (monarch) mode.
 *
 *
 ************************************************************************/
#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
	/* Bamboo is always configured as host. */
	return (1);
}
#endif				/* defined(CONFIG_PCI) */

/*************************************************************************
 *  hw_watchdog_reset
 *
 *	This routine is called to reset (keep alive) the watchdog timer
 *
 ************************************************************************/
#if defined(CONFIG_HW_WATCHDOG)
void hw_watchdog_reset(void)
{
}
#endif