skgehw.h

适合KS8695X

	/* 0x0e19:	reserved */
#define GMAC_TI_ST_TST	0x0e1a	/*  8 bit	Time Stamp Timer Test Reg */
	/* 0x0e1b - 0x0e7f:	reserved */

/*
 *	Bank 29
 */
	/* 0x0e80 - 0x0efc:	reserved */

/*
 *	Bank 30
 */
/* GMAC and GPHY Control Registers (YUKON only) */
#define GMAC_CTRL		0x0f00	/* 32 bit	GMAC Control Reg */
#define GPHY_CTRL		0x0f04	/* 32 bit	GPHY Control Reg */
#define GMAC_IRQ_SRC	0x0f08	/*  8 bit	GMAC Interrupt Source Reg */
	/* 0x0f09 - 0x0f0b:	reserved */
#define GMAC_IRQ_MSK	0x0f0c	/*  8 bit	GMAC Interrupt Mask Reg */
	/* 0x0f0d - 0x0f0f:	reserved */
#define GMAC_LINK_CTRL	0x0f10	/* 16 bit	Link Control Reg */
	/* 0x0f14 - 0x0f1f:	reserved */

/* Wake-up Frame Pattern Match Control Registers (YUKON only) */

#define WOL_REG_OFFS	0x20	/* HW-Bug: Address is + 0x20 against spec. */

#define WOL_CTRL_STAT	0x0f20	/* 16 bit	WOL Control/Status Reg */
#define WOL_MATCH_CTL	0x0f22	/*  8 bit	WOL Match Control Reg */
#define WOL_MATCH_RES	0x0f23	/*  8 bit	WOL Match Result Reg */
#define WOL_MAC_ADDR_LO	0x0f24	/* 32 bit	WOL MAC Address Low */
#define WOL_MAC_ADDR_HI	0x0f28	/* 16 bit	WOL MAC Address High */
#define WOL_PATT_RPTR	0x0f2c	/*  8 bit	WOL Pattern Read Ptr */

/* use this macro to access above registers */
#define WOL_REG(Reg)	((Reg) + (pAC->GIni.GIWolOffs))


/* WOL Pattern Length Registers (YUKON only) */

#define WOL_PATT_LEN_LO	0x0f30		/* 32 bit	WOL Pattern Length 3..0 */
#define WOL_PATT_LEN_HI	0x0f34		/* 24 bit	WOL Pattern Length 6..4 */

/* WOL Pattern Counter Registers (YUKON only) */

#define WOL_PATT_CNT_0	0x0f38		/* 32 bit	WOL Pattern Counter 3..0 */
#define WOL_PATT_CNT_4	0x0f3c		/* 24 bit	WOL Pattern Counter 6..4 */
	/* 0x0f40 - 0x0f7f:	reserved */

/*
 *	Bank 31
 */
/* 0x0f80 - 0x0fff:	reserved */

/*
 *	Bank 32	- 33
 */
#define WOL_PATT_RAM_1	0x1000	/*  WOL Pattern RAM Link 1 */

/*
 *	Bank 0x22 - 0x3f
 */
/* 0x1100 - 0x1fff:	reserved */

/*
 *	Bank 0x40 - 0x4f
 */
#define BASE_XMAC_1		0x2000	/* XMAC 1 registers */

/*
 *	Bank 0x50 - 0x5f
 */

#define BASE_GMAC_1		0x2800	/* GMAC 1 registers */

/*
 *	Bank 0x60 - 0x6f
 */
#define BASE_XMAC_2		0x3000	/* XMAC 2 registers */

/*
 *	Bank 0x70 - 0x7f
 */
#define BASE_GMAC_2		0x3800	/* GMAC 2 registers */

/*
 *	Control Register Bit Definitions:
 */
/*	B0_RAP		8 bit	Register Address Port */
								/* Bit 7:	reserved */
#define RAP_RAP			0x3f	/* Bit 6..0:	0 = block 0,..,6f = block 6f */

/*	B0_CTST		16 bit	Control/Status register */
								/* Bit 15..14:	reserved */
#define CS_CLK_RUN_HOT	BIT_13S		/* CLK_RUN hot m. (YUKON-Lite only) */
#define CS_CLK_RUN_RST	BIT_12S		/* CLK_RUN reset  (YUKON-Lite only) */
#define CS_CLK_RUN_ENA	BIT_11S		/* CLK_RUN enable (YUKON-Lite only) */
#define CS_VAUX_AVAIL	BIT_10S		/* VAUX available (YUKON only) */
#define CS_BUS_CLOCK	BIT_9S		/* Bus Clock 0/1 = 33/66 MHz */
#define CS_BUS_SLOT_SZ	BIT_8S		/* Slot Size 0/1 = 32/64 bit slot */
#define CS_ST_SW_IRQ	BIT_7S		/* Set IRQ SW Request */
#define CS_CL_SW_IRQ	BIT_6S		/* Clear IRQ SW Request */
#define CS_STOP_DONE	BIT_5S		/* Stop Master is finished */
#define CS_STOP_MAST	BIT_4S		/* Command Bit to stop the master */
#define CS_MRST_CLR		BIT_3S		/* Clear Master reset	*/
#define CS_MRST_SET		BIT_2S		/* Set Master reset	*/
#define CS_RST_CLR		BIT_1S		/* Clear Software reset	*/
#define CS_RST_SET		BIT_0S		/* Set   Software reset	*/

/*	B0_LED		 8 Bit	LED register */
								/* Bit  7.. 2:	reserved */
#define LED_STAT_ON		BIT_1S		/* Status LED on	*/
#define LED_STAT_OFF	BIT_0S		/* Status LED off	*/

/*	B0_POWER_CTRL	 8 Bit	Power Control reg (YUKON only) */
#define PC_VAUX_ENA		BIT_7		/* Switch VAUX Enable  */
#define PC_VAUX_DIS		BIT_6       /* Switch VAUX Disable */
#define PC_VCC_ENA		BIT_5       /* Switch VCC Enable  */
#define PC_VCC_DIS		BIT_4       /* Switch VCC Disable */
#define PC_VAUX_ON		BIT_3       /* Switch VAUX On  */
#define PC_VAUX_OFF		BIT_2       /* Switch VAUX Off */
#define PC_VCC_ON		BIT_1       /* Switch VCC On  */
#define PC_VCC_OFF		BIT_0       /* Switch VCC Off */

/*	B0_ISRC		32 bit	Interrupt Source Register */
/*	B0_IMSK		32 bit	Interrupt Mask Register */
/*	B0_SP_ISRC	32 bit	Special Interrupt Source Reg */
/*	B2_IRQM_MSK 	32 bit	IRQ Moderation Mask */
#define IS_ALL_MSK		0xbfffffffL	/* 		All Interrupt bits */
#define IS_HW_ERR		BIT_31		/* Interrupt HW Error */
								/* Bit 30:	reserved */
#define IS_PA_TO_RX1	BIT_29		/* Packet Arb Timeout Rx1 */
#define IS_PA_TO_RX2	BIT_28		/* Packet Arb Timeout Rx2 */
#define IS_PA_TO_TX1	BIT_27		/* Packet Arb Timeout Tx1 */
#define IS_PA_TO_TX2	BIT_26		/* Packet Arb Timeout Tx2 */
#define IS_I2C_READY	BIT_25		/* IRQ on end of I2C Tx */
#define IS_IRQ_SW		BIT_24		/* SW forced IRQ	*/
#define IS_EXT_REG		BIT_23		/* IRQ from LM80 or PHY (GENESIS only) */
									/* IRQ from PHY (YUKON only) */
#define IS_TIMINT		BIT_22		/* IRQ from Timer	*/
#define IS_MAC1			BIT_21		/* IRQ from MAC 1	*/
#define IS_LNK_SYNC_M1	BIT_20		/* Link Sync Cnt wrap MAC 1 */
#define IS_MAC2			BIT_19		/* IRQ from MAC 2	*/
#define IS_LNK_SYNC_M2	BIT_18		/* Link Sync Cnt wrap MAC 2 */
/* Receive Queue 1 */
#define IS_R1_B			BIT_17		/* Q_R1 End of Buffer */
#define IS_R1_F			BIT_16		/* Q_R1 End of Frame */
#define IS_R1_C			BIT_15		/* Q_R1 Encoding Error */
/* Receive Queue 2 */
#define IS_R2_B			BIT_14		/* Q_R2 End of Buffer */
#define IS_R2_F			BIT_13		/* Q_R2 End of Frame */
#define IS_R2_C			BIT_12		/* Q_R2 Encoding Error */
/* Synchronous Transmit Queue 1 */
#define IS_XS1_B		BIT_11		/* Q_XS1 End of Buffer */
#define IS_XS1_F		BIT_10		/* Q_XS1 End of Frame */
#define IS_XS1_C		BIT_9		/* Q_XS1 Encoding Error */
/* Asynchronous Transmit Queue 1 */
#define IS_XA1_B		BIT_8		/* Q_XA1 End of Buffer */
#define IS_XA1_F		BIT_7		/* Q_XA1 End of Frame */
#define IS_XA1_C		BIT_6		/* Q_XA1 Encoding Error */
/* Synchronous Transmit Queue 2 */
#define IS_XS2_B		BIT_5		/* Q_XS2 End of Buffer */
#define IS_XS2_F		BIT_4		/* Q_XS2 End of Frame */
#define IS_XS2_C		BIT_3		/* Q_XS2 Encoding Error */
/* Asynchronous Transmit Queue 2 */
#define IS_XA2_B		BIT_2		/* Q_XA2 End of Buffer */
#define IS_XA2_F		BIT_1		/* Q_XA2 End of Frame */
#define IS_XA2_C		BIT_0		/* Q_XA2 Encoding Error */


/*	B0_HWE_ISRC	32 bit	HW Error Interrupt Src Reg */
/*	B0_HWE_IMSK	32 bit	HW Error Interrupt Mask Reg */
/*	B2_IRQM_HWE_MSK 32 bit	IRQ Moderation HW Error Mask */
#define IS_ERR_MSK		0x00000fffL	/* 		All Error bits */
								/* Bit 31..14:	reserved */
#define IS_IRQ_TIST_OV	BIT_13	/* Time Stamp Timer Overflow (YUKON only) */
#define IS_IRQ_SENSOR	BIT_12	/* IRQ from Sensor (YUKON only) */
#define IS_IRQ_MST_ERR	BIT_11	/* IRQ master error detected */
#define IS_IRQ_STAT		BIT_10	/* IRQ status exception */
#define IS_NO_STAT_M1	BIT_9	/* No Rx Status from MAC 1 */
#define IS_NO_STAT_M2	BIT_8	/* No Rx Status from MAC 2 */
#define IS_NO_TIST_M1	BIT_7	/* No Time Stamp from MAC 1 */
#define IS_NO_TIST_M2	BIT_6	/* No Time Stamp from MAC 2 */
#define IS_RAM_RD_PAR	BIT_5	/* RAM Read  Parity Error */
#define IS_RAM_WR_PAR	BIT_4	/* RAM Write Parity Error */
#define IS_M1_PAR_ERR	BIT_3	/* MAC 1 Parity Error */
#define IS_M2_PAR_ERR	BIT_2	/* MAC 2 Parity Error */
#define IS_R1_PAR_ERR	BIT_1	/* Queue R1 Parity Error */
#define IS_R2_PAR_ERR	BIT_0	/* Queue R2 Parity Error */

/*	B2_CONN_TYP	 8 bit	Connector type */
/*	B2_PMD_TYP	 8 bit	PMD type */
/*	Values of connector and PMD type comply to SysKonnect internal std */

/*	B2_MAC_CFG	 8 bit	MAC Configuration / Chip Revision */
#define CFG_CHIP_R_MSK	(0xf<<4)	/* Bit 7.. 4: Chip Revision */
									/* Bit 3.. 2:	reserved */
#define CFG_DIS_M2_CLK	BIT_1S		/* Disable Clock for 2nd MAC */
#define CFG_SNG_MAC		BIT_0S		/* MAC Config: 0=2 MACs / 1=1 MAC*/

/*	B2_CHIP_ID	 8 bit 	Chip Identification Number */
#define CHIP_ID_GENESIS	0x0a		/* Chip ID for GENESIS */
#define CHIP_ID_YUKON	0xb0		/* Chip ID for YUKON */

/*	B2_FAR		32 bit	Flash-Prom Addr Reg/Cnt */
#define FAR_ADDR		0x1ffffL	/* Bit 16.. 0:	FPROM Address mask */

/*	B2_LD_CRTL	 8 bit	EPROM loader control register */
/*	Bits are currently reserved */

/*	B2_LD_TEST	 8 bit	EPROM loader test register */
								/* Bit 7.. 4:	reserved */
#define LD_T_ON			BIT_3S	/* Loader Test mode on */
#define LD_T_OFF		BIT_2S	/* Loader Test mode off */
#define LD_T_STEP		BIT_1S	/* Decrement FPROM addr. Counter */
#define LD_START		BIT_0S	/* Start loading FPROM */

/*
 *	Timer Section
 */
/*	B2_TI_CRTL	 8 bit	Timer control */
/*	B2_IRQM_CTRL	 8 bit	IRQ Moderation Timer Control */
								/* Bit 7.. 3:	reserved */
#define TIM_START		BIT_2S	/* Start Timer */
#define TIM_STOP		BIT_1S	/* Stop  Timer */
#define TIM_CLR_IRQ		BIT_0S	/* Clear Timer IRQ (!IRQM) */

/*	B2_TI_TEST	 8 Bit	Timer Test */
/*	B2_IRQM_TEST	 8 bit	IRQ Moderation Timer Test */
/*	B28_DPT_TST	 8 bit	Descriptor Poll Timer Test Reg */
								/* Bit 7.. 3:	reserved */
#define TIM_T_ON		BIT_2S	/* Test mode on */
#define TIM_T_OFF		BIT_1S	/* Test mode off */
#define TIM_T_STEP		BIT_0S	/* Test step */

/*	B28_DPT_INI	32 bit	Descriptor Poll Timer Init Val */
/*	B28_DPT_VAL	32 bit	Descriptor Poll Timer Curr Val */
								/* Bit 31..24:	reserved */
#define DPT_MSK		0x00ffffffL	/* Bit 23.. 0:	Desc Poll Timer Bits */

/*	B28_DPT_CTRL	 8 bit	Descriptor Poll Timer Ctrl Reg */
								/* Bit  7.. 2:	reserved */
#define DPT_START		BIT_1S	/* Start Descriptor Poll Timer */
#define DPT_STOP		BIT_0S	/* Stop  Descriptor Poll Timer */

/*	B2_E_3			 8 bit 	lower 4 bits used for HW self test result */
#define B2_E3_RES_MASK	0x0f

/*	B2_TST_CTRL1	 8 bit	Test Control Register 1 */
#define TST_FRC_DPERR_MR	BIT_7S	/* force DATAPERR on MST RD */
#define TST_FRC_DPERR_MW	BIT_6S	/* force DATAPERR on MST WR */
#define TST_FRC_DPERR_TR	BIT_5S	/* force DATAPERR on TRG RD */
#define TST_FRC_DPERR_TW	BIT_4S	/* force DATAPERR on TRG WR */
#define TST_FRC_APERR_M		BIT_3S	/* force ADDRPERR on MST */
#define TST_FRC_APERR_T		BIT_2S	/* force ADDRPERR on TRG */
#define TST_CFG_WRITE_ON	BIT_1S	/* Enable  Config Reg WR */
#define TST_CFG_WRITE_OFF	BIT_0S	/* Disable Config Reg WR */

/*	B2_TST_CTRL2	 8 bit	Test Control Register 2 */
									/* Bit 7.. 4:	reserved */
			/* force the following error on the next master read/write	*/
#define TST_FRC_DPERR_MR64	BIT_3S	/* DataPERR RD 64	*/
#define TST_FRC_DPERR_MW64	BIT_2S	/* DataPERR WR 64	*/
#define TST_FRC_APERR_1M64	BIT_1S	/* AddrPERR on 1. phase */
#define TST_FRC_APERR_2M64	BIT_0S	/* AddrPERR on 2. phase */

/*	B2_GP_IO	32 bit	General Purpose I/O Register */
							/* Bit 31..26:	reserved */
#define GP_DIR_9	BIT_25	/* IO_9 direct, 0=I/1=O */
#define GP_DIR_8	BIT_24	/* IO_8 direct, 0=I/1=O */
#define GP_DIR_7	BIT_23	/* IO_7 direct, 0=I/1=O */
#define GP_DIR_6	BIT_22	/* IO_6 direct, 0=I/1=O */
#define GP_DIR_5	BIT_21	/* IO_5 direct, 0=I/1=O */
#define GP_DIR_4	BIT_20	/* IO_4 direct, 0=I/1=O */
#define GP_DIR_3	BIT_19	/* IO_3 direct, 0=I/1=O */
#define GP_DIR_2	BIT_18	/* IO_2 direct, 0=I/1=O */
#define GP_DIR_1	BIT_17	/* IO_1 direct, 0=I/1=O */
#define GP_DIR_0	BIT_16	/* IO_0 direct, 0=I/1=O */
						/* Bit 15..10:	reserved */
#define GP_IO_9		BIT_9	/* IO_9 pin */
#define GP_IO_8		BIT_8	/* IO_8 pin */
#define GP_IO_7		BIT_7	/* IO_7 pin */
#define GP_IO_6		BIT_6	/* IO_6 pin */
#define GP_IO_5		BIT_5	/* IO_5 pin */
#define GP_IO_4		BIT_4	/* IO_4 pin */
#define GP_IO_3		BIT_3	/* IO_3 pin */
#define GP_IO_2		BIT_2	/* IO_2 pin */
#define GP_IO_1		BIT_1	/* IO_1 pin */
#define GP_IO_0		BIT_0	/* IO_0 pin */

/*	B2_I2C_CTRL	32 bit	I2C HW Control Register */
#define I2C_FLAG		BIT_31		/* Start read/write if WR */
#define I2C_ADDR		(0x7fffL<<16)	/* Bit 30..16:	Addr to be RD/WR */
#define I2C_DEV_SEL		(0x7fL<<9)		/* Bit 15.. 9:	I2C Device Select */
								/* Bit	8.. 5:	reserved	*/
#define I2C_BURST_LEN	BIT_4		/* Burst Len, 1/4 bytes */
#define I2C_DEV_SIZE	(7L<<1)		/* Bit	3.. 1:	I2C Device Size	*/
#define I2C_025K_DEV	(0L<<1)		/*		0: 256 Bytes or smal. */
#define I2C_05K_DEV		(1L<<1)		/* 		1: 512	Bytes	*/
#define I2C_1K_DEV		(2L<<1)		/*		2: 1024 Bytes	*/
#define I2C_2K_DEV		(3L<<1)		/*		3: 2048	Bytes	*/
#define I2C_4K_DEV		(4L<<1)		/*		4: 4096 Bytes	*/
#define I2C_8K_DEV		(5L<<1)		/*		5: 8192 Bytes	*/
#define I2C_16K_DEV		(6L<<1)		/*		6: 16384 Bytes	*/
#define I2C_32K_DEV		(7L<<1)		/*		7: 32768 Bytes	*/
#define I2C_STOP		BIT_0		/* Interrupt I2C transfer */