linux-2.6.12-rc4-mips-headers.patch

mips-nptl patches for crosstool-0.34

@@ -62,7 +62,7 @@
 
 /* The structure of a DMA Channel.
 */
-typedef struct au1xxx_dma_channel {
+typedef volatile struct au1xxx_dma_channel {
 	u32	ddma_cfg;	/* See below */
 	u32	ddma_desptr;	/* 32-byte aligned pointer to descriptor */
 	u32	ddma_statptr;	/* word aligned pointer to status word */
@@ -98,7 +98,7 @@
 /* "Standard" DDMA Descriptor.
  * Must be 32-byte aligned.
  */
-typedef struct au1xxx_ddma_desc {
+typedef volatile struct au1xxx_ddma_desc {
 	u32	dscr_cmd0;		/* See below */
 	u32	dscr_cmd1;		/* See below */
 	u32	dscr_source0;		/* source phys address */
@@ -107,6 +107,12 @@
 	u32	dscr_dest1;		/* See below */
 	u32	dscr_stat;		/* completion status */
 	u32	dscr_nxtptr;		/* Next descriptor pointer (mostly) */
+	/* First 32bytes are HW specific!!!
+	   Lets have some SW data following.. make sure its 32bytes
+	 */
+	u32	sw_status;
+	u32 	sw_context;
+	u32	sw_reserved[6];
 } au1x_ddma_desc_t;
 
 #define DSCR_CMD0_V		(1 << 31)	/* Descriptor valid */
@@ -125,8 +131,11 @@
 #define DSCR_CMD0_CV		(0x1 << 2)	/* Clear Valid when done */
 #define DSCR_CMD0_ST_MASK	(0x3 << 0)	/* Status instruction */
 
+#define SW_STATUS_INUSE		(1<<0)
+
 /* Command 0 device IDs.
 */
+#ifdef CONFIG_SOC_AU1550
 #define DSCR_CMD0_UART0_TX	0
 #define DSCR_CMD0_UART0_RX	1
 #define DSCR_CMD0_UART3_TX	2
@@ -155,9 +164,45 @@
 #define DSCR_CMD0_MAC0_TX	25
 #define DSCR_CMD0_MAC1_RX	26
 #define DSCR_CMD0_MAC1_TX	27
+#endif /* CONFIG_SOC_AU1550 */
+
+#ifdef CONFIG_SOC_AU1200
+#define DSCR_CMD0_UART0_TX	0
+#define DSCR_CMD0_UART0_RX	1
+#define DSCR_CMD0_UART1_TX	2
+#define DSCR_CMD0_UART1_RX	3
+#define DSCR_CMD0_DMA_REQ0	4
+#define DSCR_CMD0_DMA_REQ1	5
+#define DSCR_CMD0_MAE_BE	6
+#define DSCR_CMD0_MAE_FE	7
+#define DSCR_CMD0_SDMS_TX0	8
+#define DSCR_CMD0_SDMS_RX0	9
+#define DSCR_CMD0_SDMS_TX1	10
+#define DSCR_CMD0_SDMS_RX1	11
+#define DSCR_CMD0_AES_TX	13
+#define DSCR_CMD0_AES_RX	12
+#define DSCR_CMD0_PSC0_TX	14
+#define DSCR_CMD0_PSC0_RX	15
+#define DSCR_CMD0_PSC1_TX	16
+#define DSCR_CMD0_PSC1_RX	17
+#define DSCR_CMD0_CIM_RXA	18
+#define DSCR_CMD0_CIM_RXB	19
+#define DSCR_CMD0_CIM_RXC	20
+#define DSCR_CMD0_MAE_BOTH	21
+#define DSCR_CMD0_LCD		22
+#define DSCR_CMD0_NAND_FLASH	23
+#define DSCR_CMD0_PSC0_SYNC	24
+#define DSCR_CMD0_PSC1_SYNC	25
+#define DSCR_CMD0_CIM_SYNC	26
+#endif /* CONFIG_SOC_AU1200 */
+
 #define DSCR_CMD0_THROTTLE	30
 #define DSCR_CMD0_ALWAYS	31
 #define DSCR_NDEV_IDS		32
+/* THis macro is used to find/create custom device types */
+#define DSCR_DEV2CUSTOM_ID(x,d)	(((((x)&0xFFFF)<<8)|0x32000000)|((d)&0xFF))
+#define DSCR_CUSTOM2DEV_ID(x)	((x)&0xFF)
+
 
 #define DSCR_CMD0_SID(x)	(((x) & 0x1f) << 25)
 #define DSCR_CMD0_DID(x)	(((x) & 0x1f) << 20)
@@ -246,6 +291,43 @@
 */
 #define NUM_DBDMA_CHANS	16
 
+/*
+ * Ddma API definitions
+ * FIXME: may not fit to this header file
+ */
+typedef struct dbdma_device_table {
+	u32		dev_id;
+	u32		dev_flags;
+	u32		dev_tsize;
+	u32		dev_devwidth;
+	u32		dev_physaddr;		/* If FIFO */
+	u32		dev_intlevel;
+	u32		dev_intpolarity;
+} dbdev_tab_t;
+
+
+typedef struct dbdma_chan_config {
+	spinlock_t      lock;
+
+	u32			chan_flags;
+	u32			chan_index;
+	dbdev_tab_t		*chan_src;
+	dbdev_tab_t		*chan_dest;
+	au1x_dma_chan_t		*chan_ptr;
+	au1x_ddma_desc_t	*chan_desc_base;
+	au1x_ddma_desc_t	*get_ptr, *put_ptr, *cur_ptr;
+	void			*chan_callparam;
+	void (*chan_callback)(int, void *, struct pt_regs *);
+} chan_tab_t;
+
+#define DEV_FLAGS_INUSE		(1 << 0)
+#define DEV_FLAGS_ANYUSE	(1 << 1)
+#define DEV_FLAGS_OUT		(1 << 2)
+#define DEV_FLAGS_IN		(1 << 3)
+#define DEV_FLAGS_BURSTABLE (1 << 4)
+#define DEV_FLAGS_SYNC		(1 << 5)
+/* end Ddma API definitions */
+
 /* External functions for drivers to use.
 */
 /* Use this to allocate a dbdma channel.  The device ids are one of the
@@ -258,18 +340,6 @@
 
 #define DBDMA_MEM_CHAN	DSCR_CMD0_ALWAYS
 
-/* ACK!  These should be in a board specific description file.
-*/
-#ifdef CONFIG_MIPS_PB1550
-#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
-#endif
-#ifdef CONFIG_MIPS_DB1550
-#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
-#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
-#endif
-
-
 /* Set the device width of a in/out fifo.
 */
 u32 au1xxx_dbdma_set_devwidth(u32 chanid, int bits);
@@ -280,8 +350,8 @@
 
 /* Put buffers on source/destination descriptors.
 */
-u32 au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes);
-u32 au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes);
+u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags);
+u32 _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags);
 
 /* Get a buffer from the destination descriptor.
 */
@@ -295,5 +365,25 @@
 void au1xxx_dbdma_chan_free(u32 chanid);
 void au1xxx_dbdma_dump(u32 chanid);
 
+u32 au1xxx_dbdma_put_dscr(u32 chanid, au1x_ddma_desc_t *dscr );
+
+u32 au1xxx_ddma_add_device( dbdev_tab_t *dev );
+
+/*
+ 	Some compatibilty macros --
+		Needed to make changes to API without breaking existing drivers
+*/
+#define	au1xxx_dbdma_put_source(chanid,buf,nbytes)_au1xxx_dbdma_put_source(chanid, buf, nbytes, DDMA_FLAGS_IE)
+#define	au1xxx_dbdma_put_source_flags(chanid,buf,nbytes,flags) _au1xxx_dbdma_put_source(chanid, buf, nbytes, flags)
+
+#define au1xxx_dbdma_put_dest(chanid,buf,nbytes) _au1xxx_dbdma_put_dest(chanid, buf, nbytes, DDMA_FLAGS_IE)
+#define	au1xxx_dbdma_put_dest_flags(chanid,buf,nbytes,flags) _au1xxx_dbdma_put_dest(chanid, buf, nbytes, flags)
+
+/*
+ *	Flags for the put_source/put_dest functions.
+ */
+#define DDMA_FLAGS_IE	(1<<0)
+#define DDMA_FLAGS_NOIE (1<<1)
+
 #endif /* _LANGUAGE_ASSEMBLY */
 #endif /* _AU1000_DBDMA_H_ */
diff -urN -x CVS -x .cvsignore linux-2.6.12-rc4/include/asm-mips/mach-au1x00/au1xxx_psc.h /data/cvs-ext/linux-2.6-mips/linux/include/asm-mips/mach-au1x00/au1xxx_psc.h
--- linux-2.6.12-rc4/include/asm-mips/mach-au1x00/au1xxx_psc.h	2005-04-27 13:23:30.000000000 -0500
+++ /data/cvs-ext/linux-2.6-mips/linux/include/asm-mips/mach-au1x00/au1xxx_psc.h	2005-04-14 20:08:31.969760518 -0500
@@ -33,6 +33,8 @@
 #ifndef _AU1000_PSC_H_
 #define _AU1000_PSC_H_
 
+#include <linux/config.h>
+
 /* The PSC base addresses.  */
 #ifdef CONFIG_SOC_AU1550
 #define PSC0_BASE_ADDR		0xb1a00000
diff -urN -x CVS -x .cvsignore linux-2.6.12-rc4/include/asm-mips/mach-db1x00/db1200.h /data/cvs-ext/linux-2.6-mips/linux/include/asm-mips/mach-db1x00/db1200.h
--- linux-2.6.12-rc4/include/asm-mips/mach-db1x00/db1200.h	1969-12-31 18:00:00.000000000 -0600
+++ /data/cvs-ext/linux-2.6-mips/linux/include/asm-mips/mach-db1x00/db1200.h	2005-04-14 20:08:32.001755205 -0500
@@ -0,0 +1,214 @@
+/*
+ * AMD Alchemy DB1200 Referrence Board
+ * Board Registers defines.
+ *
+ * ########################################################################
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * ########################################################################
+ *
+ *
+ */
+#ifndef __ASM_DB1200_H
+#define __ASM_DB1200_H
+
+#include <linux/types.h>
+
+// This is defined in au1000.h with bogus value
+#undef AU1X00_EXTERNAL_INT
+
+#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX
+#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX
+#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC1_TX
+#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC1_RX
+
+/* SPI and SMB are muxed on the Pb1200 board.
+   Refer to board documentation.
+ */
+#define SPI_PSC_BASE        PSC0_BASE_ADDR
+#define SMBUS_PSC_BASE      PSC0_BASE_ADDR
+/* AC97 and I2S are muxed on the Pb1200 board.
+   Refer to board documentation.
+ */
+#define AC97_PSC_BASE       PSC1_BASE_ADDR
+#define I2S_PSC_BASE		PSC1_BASE_ADDR
+
+#define BCSR_KSEG1_ADDR 0xB9800000
+
+typedef volatile struct
+{
+	/*00*/	u16 whoami;
+		u16 reserved0;
+	/*04*/	u16 status;
+		u16 reserved1;
+	/*08*/	u16 switches;
+		u16 reserved2;
+	/*0C*/	u16 resets;
+		u16 reserved3;
+
+	/*10*/	u16 pcmcia;
+		u16 reserved4;
+	/*14*/	u16 board;
+		u16 reserved5;
+	/*18*/	u16 disk_leds;
+		u16 reserved6;
+	/*1C*/	u16 system;
+		u16 reserved7;
+
+	/*20*/	u16 intclr;
+		u16 reserved8;
+	/*24*/	u16 intset;
+		u16 reserved9;
+	/*28*/	u16 intclr_mask;
+		u16 reserved10;
+	/*2C*/	u16 intset_mask;
+		u16 reserved11;
+
+	/*30*/	u16 sig_status;
+		u16 reserved12;
+	/*34*/	u16 int_status;
+		u16 reserved13;
+	/*38*/	u16 reserved14;
+		u16 reserved15;
+	/*3C*/	u16 reserved16;
+		u16 reserved17;
+
+} BCSR;
+
+static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+/*
+ * Register bit definitions for the BCSRs
+ */
+#define BCSR_WHOAMI_DCID	0x000F
+#define BCSR_WHOAMI_CPLD	0x00F0
+#define BCSR_WHOAMI_BOARD	0x0F00
+
+#define BCSR_STATUS_PCMCIA0VS	0x0003
+#define BCSR_STATUS_PCMCIA1VS	0x000C
+#define BCSR_STATUS_SWAPBOOT	0x0040
+#define BCSR_STATUS_FLASHBUSY	0x0100
+#define BCSR_STATUS_IDECBLID	0x0200
+#define BCSR_STATUS_SD0WP		0x0400
+#define BCSR_STATUS_U0RXD		0x1000
+#define BCSR_STATUS_U1RXD		0x2000
+
+#define BCSR_SWITCHES_OCTAL	0x00FF
+#define BCSR_SWITCHES_DIP_1	0x0080
+#define BCSR_SWITCHES_DIP_2	0x0040
+#define BCSR_SWITCHES_DIP_3	0x0020
+#define BCSR_SWITCHES_DIP_4	0x0010
+#define BCSR_SWITCHES_DIP_5	0x0008
+#define BCSR_SWITCHES_DIP_6	0x0004
+#define BCSR_SWITCHES_DIP_7	0x0002
+#define BCSR_SWITCHES_DIP_8	0x0001
+#define BCSR_SWITCHES_ROTARY	0x0F00
+
+#define BCSR_RESETS_ETH		0x0001
+#define BCSR_RESETS_CAMERA	0x0002
+#define BCSR_RESETS_DC		0x0004
+#define BCSR_RESETS_IDE		0x0008
+#define BCSR_RESETS_TV		0x0010
+/* not resets but in the same register */
+#define BCSR_RESETS_PWMR1mUX 0x0800
+#define BCSR_RESETS_PCS0MUX	0x1000
+#define BCSR_RESETS_PCS1MUX	0x2000
+#define BCSR_RESETS_SPISEL	0x4000
+
+#define BCSR_PCMCIA_PC0VPP	0x0003
+#define BCSR_PCMCIA_PC0VCC	0x000C
+#define BCSR_PCMCIA_PC0DRVEN	0x0010
+#define BCSR_PCMCIA_PC0RST	0x0080
+#define BCSR_PCMCIA_PC1VPP	0x0300
+#define BCSR_PCMCIA_PC1VCC	0x0C00
+#define BCSR_PCMCIA_PC1DRVEN	0x1000
+#define BCSR_PCMCIA_PC1RST	0x8000
+
+#define BCSR_BOARD_LCDVEE	0x0001
+#define BCSR_BOARD_LCDVDD	0x0002
+#define BCSR_BOARD_LCDBL	0x0004
+#define BCSR_BOARD_CAMSNAP	0x0010
+#define BCSR_BOARD_CAMPWR	0x0020
+#define BCSR_BOARD_SD0PWR	0x0040
+
+#define BCSR_LEDS_DECIMALS	0x0003
+#define BCSR_LEDS_LED0		0x0100
+#define BCSR_LEDS_LED1		0x0200
+#define BCSR_LEDS_LED2		0x0400
+#define BCSR_LEDS_LED3		0x0800
+
+#define BCSR_SYSTEM_POWEROFF	0x4000
+#define BCSR_SYSTEM_RESET	0x8000
+
+/* Bit positions for the different interrupt sources */
+#define BCSR_INT_IDE		0x0001
+#define BCSR_INT_ETH		0x0002
+#define BCSR_INT_PC0		0x0004
+#define BCSR_INT_PC0STSCHG	0x0008
+#define BCSR_INT_PC1		0x0010
+#define BCSR_INT_PC1STSCHG	0x0020
+#define BCSR_INT_DC			0x0040
+#define BCSR_INT_FLASHBUSY	0x0080
+#define BCSR_INT_PC0INSERT	0x0100
+#define BCSR_INT_PC0EJECT	0x0200
+#define BCSR_INT_PC1INSERT	0x0400
+#define BCSR_INT_PC1EJECT	0x0800
+#define BCSR_INT_SD0INSERT	0x1000
+#define BCSR_INT_SD0EJECT	0x2000
+
+#define AU1XXX_SMC91111_PHYS_ADDR	(0x19000300)
+#define AU1XXX_SMC91111_IRQ			DB1200_ETH_INT
+
+#define AU1XXX_ATA_PHYS_ADDR		(0x18800000)
+#define AU1XXX_ATA_PHYS_LEN			(0x100)
+#define AU1XXX_ATA_REG_OFFSET	(5)
+#define AU1XXX_ATA_INT			DB1200_IDE_INT
+#define AU1XXX_ATA_DDMA_REQ		DSCR_CMD0_DMA_REQ1;
+#define AU1XXX_ATA_RQSIZE		128
+
+#define NAND_PHYS_ADDR   0x20000000
+
+/*
+ *	External Interrupts for Pb1200 as of 8/6/2004.
+ *   Bit positions in the CPLD registers can be calculated by taking
+ *   the interrupt define and subtracting the D