📄 lcd.pin
字号:
-- Copyright (C) 1991-2006 Altera Corporation
-- Your use of Altera Corporation's design tools, logic functions
-- and other software and tools, and its AMPP partner logic
-- functions, and any output files any of the foregoing
-- (including device programming or simulation files), and any
-- associated documentation or information are expressly subject
-- to the terms and conditions of the Altera Program License
-- Subscription Agreement, Altera MegaCore Function License
-- Agreement, or other applicable license agreement, including,
-- without limitation, that your use is for the sole purpose of
-- programming logic devices manufactured by Altera and sold by
-- Altera or its authorized distributors. Please refer to the
-- applicable agreement for further details.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCCINT : Dedicated power pin, which MUST be connected to VCC (2.5V/3.3V).
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- Bank 1: 3.3V
-- Bank 2: 3.3V
-- Bank 3: 3.3V
-- Bank 4: 3.3V
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
-- RESERVED_INPUT_WITH_WEAK_PULLUP : Pin is tri-stated with internal weak pull-up resistor.
---------------------------------------------------------------------------------
Quartus II Version 5.1 Build 213 01/19/2006 Service Pack 1 SJ Web Edition
CHIP "lcd" ASSIGNED TO AN: EPM1270T144C5
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
empty[4] : 1 : input : LVTTL : : 1 : Y
empty[5] : 2 : input : LVTTL : : 1 : Y
empty[6] : 3 : input : LVTTL : : 1 : Y
empty[7] : 4 : input : LVTTL : : 1 : Y
empty[8] : 5 : input : LVTTL : : 1 : Y
empty[9] : 6 : input : LVTTL : : 1 : Y
empty[10] : 7 : input : LVTTL : : 1 : Y
empty[11] : 8 : input : LVTTL : : 1 : Y
VCCIO1 : 9 : power : : 3.3V : 1 :
GNDIO : 10 : gnd : : : :
empty[12] : 11 : input : LVTTL : : 1 : Y
empty[13] : 12 : input : LVTTL : : 1 : Y
empty[14] : 13 : input : LVTTL : : 1 : Y
empty[15] : 14 : input : LVTTL : : 1 : Y
xa[12] : 15 : input : LVTTL : : 1 : Y
xa[13] : 16 : input : LVTTL : : 1 : Y
GNDINT : 17 : gnd : : : :
clk : 18 : input : LVTTL : : 1 : Y
VCCINT : 19 : power : : 3.3V : :
empty[3] : 20 : input : LVTTL : : 1 : N
xa[14] : 21 : input : LVTTL : : 1 : Y
xa[15] : 22 : input : LVTTL : : 1 : Y
empty[16] : 23 : input : LVTTL : : 1 : Y
empty[17] : 24 : input : LVTTL : : 1 : Y
VCCIO1 : 25 : power : : 3.3V : 1 :
GNDIO : 26 : gnd : : : :
empty[18] : 27 : input : LVTTL : : 1 : Y
xd[0] : 28 : input : LVTTL : : 1 : Y
xd[1] : 29 : input : LVTTL : : 1 : Y
xd[2] : 30 : input : LVTTL : : 1 : Y
xd[3] : 31 : input : LVTTL : : 1 : Y
xd[4] : 32 : input : LVTTL : : 1 : Y
TMS : 33 : input : : : 1 :
TDI : 34 : input : : : 1 :
TCK : 35 : input : : : 1 :
TDO : 36 : output : : : 1 :
xd[5] : 37 : input : LVTTL : : 4 : Y
xd[6] : 38 : input : LVTTL : : 4 : Y
xd[7] : 39 : input : LVTTL : : 4 : Y
xd[8] : 40 : input : LVTTL : : 4 : Y
xd[9] : 41 : input : LVTTL : : 4 : Y
xd[10] : 42 : input : LVTTL : : 4 : Y
xd[11] : 43 : input : LVTTL : : 4 : Y
xd[12] : 44 : input : LVTTL : : 4 : Y
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -