endpoint.c.bak

代码为Jennic的基于IEEE802.15.4协议栈星型网源代码

            {
                /* Try, try again */
                vStartAssociate();
            }
            break;

        case E_STATE_ASSOC_TO_SCAN:
            vStartScan();
            break;

        default:
            break;
        }
        break;

    case MAC_MLME_IND_BEACON_NOTIFY:
        /* Beacon has arrived. If in sync'ing mode, should only see this
           once synchronisation has been achieved. If running, use this
           to time reading of sensors. In other states, ignore it */
        switch (sDemoData.sSystem.eState)
        {
        case E_STATE_SYNCING:
            /* Can now associate */
            vStartAssociate();
            break;

        case E_STATE_RUNNING:
            /* Process received data in beacon payload */
            vProcessRxBeacon(psMlmeInd);
            break;

        default:
            break;
        }
        break;

    case MAC_MLME_IND_SYNC_LOSS:
        /* Lost sync with coordinator so try to find coordinator again */
        if (sDemoData.sSystem.eState != E_STATE_ASSOCIATING)
        {
            vStartScan();
        }
        else
        {
            sDemoData.sSystem.eState = E_STATE_ASSOC_TO_SCAN;
        }
        break;

    default:
        break;
    }
}

/****************************************************************************
 *
 * NAME: bProcessKeyPress
 *
 * DESCRIPTION:
 * Porcesses buttons, to turn on or off the remote switch or to detect a
 * reset request.
 *
 * RETURNS:
 * TRUE if reset combination detected.
 *
 ****************************************************************************/
PRIVATE bool_t bProcessKeyPress(void)
{
    uint8  u8KeysDown;

    /* Check for key press. We don't bother with a debouce
       algorithm as in all cases repeated presses have same effect
       anyway. We also don't bother to check that the hardware
       interrupt was caused by a key press */
    u8KeysDown = u8ButtonReadRfd();

    /* Keys control virtual switch value that is passed to the central
       controller */
    switch (u8KeysDown)
    {
    case E_KEY_0:
        sDemoData.sControls.u8Switch = 0;
        break;

    case E_KEY_1:
        sDemoData.sControls.u8Switch = 1;
        break;
    }

    /* Return TRUE if both keys are pressed at once, to indicate that a
       soft reset is required */
    return (u8KeysDown == E_KEYS_0_AND_1);
}

/****************************************************************************
 *
 * NAME: vProcessRead
 *
 * DESCRIPTION:
 * Gets the current readings from each sensor. If the light level causes the
 * low light alarm to be triggered, an LED is illuminated.
 *
 * RETURNS:
 * void
 *
 * NOTES:
 * This is not an efficient way to read the sensors as much time is wasted
 * waiting for the humidity and temperature sensor to complete. The sensor
 * pulls a DIO line low when it is ready, and this could be used to generate
 * an interrupt to indicate when data is ready to be read.
 *
 ****************************************************************************/
PRIVATE void vProcessRead(void)
{
    /* Read light level, adjust to range 0-6 in a slightly non-linear way */
    sDemoData.sSensors.u8AlsResult = u8FindMin((uint8)(u16ALSreadChannelResult() >> 9), 6);

    /* Set LED 1 based on light level */
    if ((sDemoData.sSensors.u8AlsResult <= sDemoData.sControls.u8LightAlarmLevel)
        && (sDemoData.sControls.u8LightAlarmLevel < 7))
    {
        vLedControl(1, TRUE);
    }
    else
    {
        vLedControl(1, FALSE);
    }

    /* Read temperature, 0-52 are acceptable. Polls until result received */
    vHTSstartReadTemp();
    sDemoData.sSensors.u8TempResult = u8FindMin((uint8)u16HTSreadTempResult(), 52);

    /* Read humidity, 0-104 are acceptable. Polls until result received */
    vHTSstartReadHumidity();
    sDemoData.sSensors.u8HtsResult = u8FindMin((uint8)u16HTSreadHumidityResult(), 104);
}

/****************************************************************************
 *
 * NAME: vProcessTxBlock
 *
 * DESCRIPTION:
 * Creates an MCPS request to transmit a frame and passes it to the 802.15.4
 * stack. The payload contains sensor information.
 *
 * RETURNS:
 * void
 *
 ****************************************************************************/
PRIVATE void vProcessTxBlock(void)
{
    MAC_McpsReqRsp_s  sMcpsReqRsp;
    MAC_McpsSyncCfm_s sMcpsSyncCfm;
    uint8 *pu8Payload;

    /* Create frame transmission request */
    sMcpsReqRsp.u8Type = MAC_MCPS_REQ_DATA;
    sMcpsReqRsp.u8ParamLength = sizeof(MAC_McpsReqData_s);
    /* Set handle so we can match confirmation to request */
    sMcpsReqRsp.uParam.sReqData.u8Handle = sDemoData.sTransceiver.u8CurrentTxHandle;
    /* Use short address for source */
    sMcpsReqRsp.uParam.sReqData.sFrame.sSrcAddr.u8AddrMode = 2;
    sMcpsReqRsp.uParam.sReqData.sFrame.sSrcAddr.u16PanId = DEMO_PAN_ID;
    sMcpsReqRsp.uParam.sReqData.sFrame.sSrcAddr.uAddr.u16Short = sDemoData.sSystem.u16ShortAddr;
    /* Use short address for destination */
    sMcpsReqRsp.uParam.sReqData.sFrame.sDstAddr.u8AddrMode = 2;
    sMcpsReqRsp.uParam.sReqData.sFrame.sDstAddr.u16PanId = DEMO_PAN_ID;
    sMcpsReqRsp.uParam.sReqData.sFrame.sDstAddr.uAddr.u16Short = DEMO_COORD_ADDR;
    /* Frame requires ack but not security, indirect transmit or GTS */
    sMcpsReqRsp.uParam.sReqData.sFrame.u8TxOptions = MAC_TX_OPTION_ACK;
    /* Payload is 8 bytes (room for expansion) and contains:
         ID byte so coordinator knows this is sensor information
         Previous beacon sequence number (for debug, can tell if beacon missed)
         Virtual switch value
         Sensor values: temp, humidity, light
    */
    sMcpsReqRsp.uParam.sReqData.sFrame.u8SduLength = 8;
    pu8Payload = sMcpsReqRsp.uParam.sReqData.sFrame.au8Sdu;
    pu8Payload[0] = DEMO_ENDPOINT_IDENTIFIER;
    pu8Payload[1] = sDemoData.sTransceiver.u8PrevRxBsn;
    pu8Payload[2] = sDemoData.sControls.u8Switch;
    pu8Payload[3] = sDemoData.sSensors.u8TempResult;
    pu8Payload[4] = sDemoData.sSensors.u8HtsResult;
    pu8Payload[5] = sDemoData.sSensors.u8AlsResult;

    /* Request transmit */
    vAppApiMcpsRequest(&sMcpsReqRsp, &sMcpsSyncCfm);
}

/****************************************************************************
 *
 * NAME: vProcessRxBeacon
 *
 * DESCRIPTION:
 * Processes the beacon payload received from the coordinator. Checks that
 * it is valid for the demo (8 bytes, with an identifier in the first byte)
 * then stores data passed from coordinator (light level alarm, remote switch
 * value). After processing reception, calls vProcessTxBlock to send a frame
 * back.
 *
 * PARAMETERS:      Name            RW  Usage
 *                  psMlmeInd       R   Pointer to MLME event structure
 *
 * RETURNS:
 * void
 *
 ****************************************************************************/
PRIVATE void vProcessRxBeacon(MAC_MlmeDcfmInd_s *psMlmeInd)
{
    uint8 *pu8Payload;
    uint8 u8RxVal;
    uint8 u8Bsn;

    /* There has been a beacon notify, so get configuration from beacon
       payload and re-synchronise timing */
    if ((psMlmeInd->uParam.sIndBeacon.u8SDUlength != 8)
        || (psMlmeInd->uParam.sIndBeacon.u8SDU[0] != DEMO_BEACON_IDENTIFIER))
    {
        /* Not the payload we were looking for */
        return;
    }

    pu8Payload = psMlmeInd->uParam.sIndBeacon.u8SDU;

    /* Store beacon sequence number */
    u8Bsn = psMlmeInd->uParam.sIndBeacon.u8BSN;

    /* Read local 'relay' control and light low alarm level, as specified by
       the user at the coordinator. Relay control is emulated by illuminating
       an LED on the board */
    u8RxVal = pu8Payload[1 + sDemoData.sSystem.u8ThisNode];
    vLedControl(0, (bool_t)(u8RxVal & 0x01));
    sDemoData.sControls.u8LightAlarmLevel = (u8RxVal >> 1) & 0x7;

    if (((uint8)(u8Bsn - sDemoData.sTransceiver.u8PrevRxBsn)) > 7)
    {
        sDemoData.sTransceiver.u8PrevRxBsn = u8Bsn;

        /* Respond to beacon by sending a frame and changing state to wait for
           it to complete */
        vProcessTxBlock();
        sDemoData.sSystem.eState = E_STATE_TX_DATA;
    }
}

/****************************************************************************
 *
 * NAME: u8FindMin
 *
 * DESCRIPTION:
 * Returns the smallest of two values.
 *
 * PARAMETERS:      Name    RW  Usage
 *                  u8Val1  R   First value to compare
 *                  u8Val2  R   Second value to compare
 *
 * RETURNS:
 * uint8, lowest of two input values
 *
 ****************************************************************************/
PRIVATE uint8 u8FindMin(uint8 u8Val1, uint8 u8Val2)
{
    if (u8Val1 < u8Val2)
    {
        return u8Val1;
    }
    return u8Val2;
}

/****************************************************************************
 *
 * NAME: vDisplayError
 *
 * DESCRIPTION:
 * Used to display fatal errors, by sending them to UART0 if this approach
 * has been enabled at compile time.
 *
 * Sits in an endless loop afterwards.
 *
 * PARAMETERS:      Name            RW  Usage
 *                  pcErrorMessage  R   Message to display
 *                  u32Data         R   Data to display
 *
 * RETURNS:
 * void, never returns
 *
 ****************************************************************************/
PRIVATE void vDisplayError(char *pcErrorMessage, uint32 u32Data)
{
#ifdef UART0_DEBUG
    vDebug(pcErrorMessage);
    vDisplayHex(u32Data, 8);
#endif

    /* Fatal error has occurred, so loop indefinitely */
    while (1);
}

/****************************************************************************
 *
 * NAME: vDebug
 *
 * DESCRIPTION:
 * Sends a string to UART0 using the hardware API.
 *
 * PARAMETERS:      Name            RW  Usage
 *                  pcMessage       R   Null-terminated message to send
 *
 * RETURNS:
 * void
 *
 ****************************************************************************/
#ifdef UART0_DEBUG
PRIVATE void vDebug(char *pcMessage)
{
    while (*pcMessage)
    {
        while ((u8AHI_UartReadLineStatus(0) & 0x20) == 0);
        vAHI_UartWriteData(0, *pcMessage);
        pcMessage++;
    }
}

PRIVATE void vDisplayHex(uint32 u32Data, int iSize)
{
    char acValue[9];
    char *pcString = acValue;
    uint8 u8Nybble;
    int i, j;

    j = 0;
    for (i = (iSize << 2) - 4; i >= 0; i -= 4)
    {
        u8Nybble = (uint8)((u32Data >> i) & 0x0f);
        u8Nybble += 0x30;
        if (u8Nybble > 0x39)
            u8Nybble += 7;

        *pcString = u8Nybble;
        pcString++;
    }
    *pcString = '\0';

    vDebug(acValue);
}
#endif

/****************************************************************************/
/***        END OF FILE                                                   ***/
/****************************************************************************/