spce061v004.h

本代码在凌阳单片机的编译环境下执行,主要实现的功能是双通道AD采样显示

	#define		C_SIO_RW_Dis			0x0020			//	Read /Write control bit applied disable
	#define		C_SIO_RW_ENB			0x0000			//	Read /Write control bit applied 
//B6
	#define		C_SIO_RD				0x0000			//	SIO Read 
	#define		C_SIO_WR				0x0040			//	SIO Write 
//B7
	#define		C_SIO_ENB				0x0080			//	Enable SIO Configuration 
	#define		C_SIO_Dis				0x0000			//	Disable SIO
//-----------------------------------------------------------------------------------//
extern void Set_SIO_Data(unsigned int);
extern unsigned int Get_SIO_Data(void);
//B7..B0	-->	Data
extern void Set_SIO_Address(unsigned long int);
extern unsigned long int Get_SIO_Address(void);
//B7..B0	-->	Address Low
//B15..B7	--> Address Mid
//B23..B16	-->	Address High
extern void Set_SIO_Addr_Low(unsigned int);
extern unsigned int Get_SIO_Addr_Low(void);
//B7..B0	-->	Data
extern void Set_SIO_Addr_Mid(unsigned int);
extern unsigned int Get_SIO_Addr_Mid(void);
//B7..B0	-->	Data
extern void Set_SIO_Addr_High(unsigned int);
extern unsigned int Get_SIO_Addr_High(void);
//B7..B0	-->	Data
extern void Set_SIO_Start(void);
	#define		C_SIOSTARTCMD			0x5555	 
extern unsigned int Get_SIO_Start(void);
//B7	-->	Busy
extern void Set_SIO_Stop(void);
	#define		C_SIOSTOPCMD			0x5555	 

//-----------------------------------------------------------------------------------//
//-----------------------------------------------------------------------------------//
extern void Set_UART_Command1(unsigned int);
//B2
	#define		C_UART_Parity_ENB			0x0004			//Enable UART	Parity Enable 
//B3
	#define		C_UART_Parity_Odd			0x0000			//Enable UART	Parity Odd 
	#define		C_UART_Parity_Even			0x0008			//Enable UART	Parity Even 
//B5
	#define		C_UART_Reset				0x0020			//UART	Internal Reset
//B6
	#define		C_UART_Tx_IRQ_ENB			0x0040			//UART	TX IRQ	Enable
//B7
	#define		C_UART_Rx_IRQ_ENB			0x0080			//UART	RX IRQ	Enable
//-----------------------------------------------------------------------------------//
extern void Set_UART_Command2(unsigned int);
//B6
	#define		C_UART_Tx_Pin_ENB			0x0040			//UART	TX Pin Enable
//B7
	#define		C_UART_Rx_Pin_ENB			0x0080			//UART	RX Pin Enable
extern unsigned int Get_UART_Command2(void);
//B3
	#define		C_UART_Parity_Error			0x0008			//UART	Parity Error 
//B4
	#define		C_UART_OverRun_Error		0x0010			//UART	Over Run Error 
//B5
	#define		C_UART_Frame_Error			0x0020			//UART	Frame Error
//B6
	#define		C_UART_Tx_RDY				0x0040			//UART	TX Ready
//B7
	#define		C_UART_Rx_RDY				0x0080			//UART	RX Ready
//-----------------------------------------------------------------------------------//
//B7..B0
extern void Set_UART_Data(unsigned int);
extern unsigned int Get_UART_Data(void);
//B15..B0
extern void Set_UART_BaudRate(unsigned int);
extern unsigned int Get_UART_BaudRate(void);
	#define		C_BaudRate_2400				0x1400			//UART	2400
	#define		C_BaudRate_4800				0x0A00			//UART	4800
	#define		C_BaudRate_9600				0x0500			//UART	9600
	#define		C_BaudRate_19200			0x0280			//UART	19200
	#define		C_BaudRate_38400			0x0140			//UART	38400
	#define		C_BaudRate_48000			0x0100			//UART	48000
//B7..B0
extern void Set_UART_BaudScalarLow(unsigned int);
extern unsigned int Get_UART_BaudScalarLow(void);
//B7..B0
extern void Set_UART_BaudScalarHigh(unsigned int);
extern unsigned int Get_UART_BaudScalarHigh(void);
//-----------------------------------------------------------------------------------//
//-----------------------------------------------------------------------------------//
extern void Mic_Input_Ctrl(unsigned int,unsigned int);
//	1:Set DAC trigger type
//		C_DA1_Direct				0x0000 			// DAC1 latch
//	 	C_DA1_LatchA				0x0080 			// 
//	 	C_DA1_LatchB				0x0100 			//
//	 	C_DA1_LatchAB				0x0180 			//
//------------------------------------------------------------
//		C_DA2_Direct				0x0000 			// DAC2 latch
//		C_DA2_LatchA				0x0020 			// 
//	 	C_DA2_LatchB				0x0040 			//
//	 	C_DA2_LatchAB				0x0060 			//
//-------------------------------------------------------------
//	 	C_AD_Direct					0x0000 			// A/D MIC_IN latch 
//	 	C_AD_LatchA					0x0008 			//
//		C_AD_LatchB					0x0010 			//
//	 	C_AD_LatchAB				0x0018 			//
//--------------------------------------------------------------
//	User can set 3 of above list, like 
//			C_DA1_LatchA+C_DA2_LatchB+C_AD_LatchA	or	
//			C_DA2_LatchAB+C_AD_LatchA
//
//	2:Select AGC enable/disable
// 		C_AGCE						0x0004 			//B3	//Have AGC
// 		C_AGCN						0x0000 			//B3	//No AGC
//-----------------------------------------------------------------------------------//
//-----------------------------------------------------------------------------------//
extern void Line_Input_Ctrl(unsigned int,unsigned int);
//	1:Set Line in channel 
//		C_ADC_CH1				0x0001 			//IOA0
//		C_ADC_CH2				0x0002 			//IOA1
//		C_ADC_CH3				0x0003 			//IOA2
//		C_ADC_CH4				0x0004 			//IOA3
//		C_ADC_CH5				0x0005 			//IOA4
//		C_ADC_CH6				0x0006 			//IOA5
//		C_ADC_CH7				0x0007 			//IOA6

//	2:Set Vextref enable/disable and V2 Ref enable/disable
//		C_VEXTREF_ENB			0x0080 			//B7	//Have Ext REF Voltage
//		C_VEXTREF_DIS			0x0000 			//B7	//No Ext REF Voltage
//		C_V2VREFB_DIS			0x0100 			//B8	//No 2V Voltage
//		C_V2VREFB_ENB			0x0000 			//B8	//Have 2V Voltage
//









//extern void	FIQ_ON();
//extern void	FIQ_OFF();
//extern void	IRQ_ON();
//extern void	IRQ_OFF();
//extern void	INT_FIQ();
//extern void	INT_IRQ();
//extern void	INT_FIQ_IRQ();
//extern void	INT_OFF();

extern void SIO_IO_Init(void);
// Set Serial IO(IB0,IB1) =(SCK,SIO) Status 
// Direct output
// Pull high
// Data low

#define	P_IOA_Data 				(volatile unsigned int *)0x7000   
#define P_IOA_Buffer 			(volatile unsigned int *)0x7001
#define P_IOA_Dir 				(volatile unsigned int *)0x7002
#define P_IOA_Attrib 			(volatile unsigned int *)0x7003
#define P_IOA_Latch 			(volatile unsigned int *)0x7004
//............................................
#define P_IOB_Data				(volatile unsigned int *)0x7005  
#define P_IOB_Buffer			(volatile unsigned int *)0x7006   
#define P_IOB_Dir				(volatile unsigned int *)0x7007   
#define P_IOB_Attrib			(volatile unsigned int *)0x7008   
//............................................
#define P_FeedBack				(volatile unsigned int *)0x7009   
#define P_TimerA_Data			(volatile unsigned int *)0x700A   
#define P_TimerA_Ctrl			(volatile unsigned int *)0x700B   
#define P_TimerB_Data			(volatile unsigned int *)0x700C   
#define P_TimerB_Ctrl			(volatile unsigned int *)0x700D   
#define P_TimeBase_Setup		(volatile unsigned int *)0x700E   
#define P_TimeBase_Clear		(volatile unsigned int *)0x700F 	
#define P_INT_Ctrl				(volatile unsigned int *)0x7010   
#define P_INT_Clear				(volatile unsigned int *)0x7011   
#define P_INT_Mask				(volatile unsigned int *)0x702D   
#define P_Watchdog_Clear		(volatile unsigned int *)0x7012   
#define P_SystemClock			(volatile unsigned int *)0x7013   
//... PA6442 New version MC52A (For EC-03)....
#define P_ADC					(volatile unsigned int *)0x7014   
#define P_ADC_Ctrl				(volatile unsigned int *)0x7015   
#define P_ADC_MUX_Ctrl			(volatile unsigned int *)0x702B   
#define P_ADC_LINEIN_Data		(volatile unsigned int *)0x702C   
#define P_DAC2					(volatile unsigned int *)0x7016   
#define P_DAC1					(volatile unsigned int *)0x7017   
#define P_DAC_Ctrl				(volatile unsigned int *)0x702A 	
//............................................
#define P_LVD_Ctrl				(volatile unsigned int *)0x7019   
//............................................
#define P_SIO_Data				(volatile unsigned int *)0x701A
#define P_SIO_Addr_Low			(volatile unsigned int *)0x701B
#define P_SIO_Addr_Mid			(volatile unsigned int *)0x701C
#define P_SIO_Addr_High			(volatile unsigned int *)0x701D
#define P_SIO_Ctrl				(volatile unsigned int *)0x701E
#define P_SIO_Start				(volatile unsigned int *)0x701F
#define P_SIO_Stop				(volatile unsigned int *)0x7020 	
//............................................
#define P_UART_Command1			(volatile unsigned int *)0x7021 	
#define P_UART_Command2			(volatile unsigned int *)0x7022 	
#define P_UART_Data				(volatile unsigned int *)0x7023  	
#define	P_UART_BaudScalarLow	(volatile unsigned int *)0x7024	
#define	P_UART_BaudScalarHigh	(volatile unsigned int *)0x7025 	

/*		
extern *P_IOA_Data;   	    	
extern *P_IOA_Buffer;       	
extern *P_IOA_Dir;           	
extern *P_IOA_Attrib;
extern *P_IOA_Latch;         	
//.....................................
extern *P_IOB_Data;         	
extern *P_IOB_Buffer;        	
extern *P_IOB_Dir;           	
extern *P_IOB_Attrib;        	
//......................................
extern *P_FeedBack;          	
extern *P_TimerA_Data;	
extern *P_TimerA_Ctrl;       	
extern *P_TimerB_Data;       	
extern *P_TimerB_Ctrl;       	
extern *P_TimeBase_Setup;  	
extern *P_TimeBase_Clear;	
extern *P_INT_Ctrl;          	
extern *P_INT_Clear;         	
extern *P_INT_Mask;          	
extern *P_Watchdog_Clear;    	
extern *P_SystemClock;       	
//.......................................
extern *P_ADC; 	        	
extern *P_ADC_Ctrl;          	
extern *P_ADC_MUX_Ctrl;      	
extern *P_ADC_LINEIN_Data;
extern *P_DAC2;              	
extern *P_DAC1;	        	
extern *P_DAC_Ctrl;
//......................................
extern *P_LVD_Ctrl;          	
//......................................
extern *P_SIO_Data;		
extern *P_SIO_Addr_Low;
extern *P_SIO_Addr_Mid;		
extern *P_SIO_Addr_High;	
extern *P_SIO_Ctrl;		
extern *P_SIO_Start;		
extern *P_SIO_Stop;		
//......................................
extern *P_UART_Command1;
extern *P_UART_Command2;	
extern *P_UART_Data;		
extern *P_UART_BaudScalarLow;
extern *P_UART_BaudScalarHigh; 	
*/			
#endif