low_pwr.c

SHARP_ARM720T_LH79524/5软件开发包_支持TFT_LCD_NAND_FLASH_ETH_USB

/**********************************************************************
 * Copyright (c) 2002 Sharp Microelectronics of the Americas
 *
 *        All rights reserved
 *      
 * $Workfile:   low_pwr.c  $
 * $Revision:   1.0  $
 * $Author:   ZhangJ  $
 * $Date:   Oct 20 2004 09:21:58  $
 *
 * SHARP MICROELECTRONICS OF THE AMERICAS MAKES NO REPRESENTATION
 * OR WARRANTIES WITH RESPECT TO THE PERFORMANCE OF THIS SOFTWARE,
 * AND SPECIFICALLY DISCLAIMS ANY RESPONSIBILITY FOR ANY DAMAGES, 
 * SPECIAL OR CONSEQUENTIAL, CONNECTED WITH THE USE OF THIS SOFTWARE.
 *
 * SHARP MICROELECTRONICS OF THE AMERICAS PROVIDES THIS SOFTWARE SOLELY 
 * FOR THE PURPOSE OF SOFTWARE DEVELOPMENT INCORPORATING THE USE OF A 
 * SHARP MICROCONTROLLER OR SYSTEM-ON-CHIP PRODUCT. USE OF THIS SOURCE
 * FILE IMPLIES ACCEPTANCE OF THESE CONDITIONS.
 *
 * Project: LH79520 EVB Example Code
 *
 * Description:
 *    This example shows how to use uart driver in interrupt mode
 *
 * Notes:
 *  
 * Revision History:
 * $Log:   //smaicnt2/pvcs/VM/sharpmcu/archives/sharpmcu/software/csps/lh79524/bsps/sdk79524/examples/low_pwr/low_pwr.c-arc  $
 * 
 *    Rev 1.0   Oct 20 2004 09:21:58   ZhangJ
 * Initial revision.
 * 
 *    Rev 1.0   Oct 31 2003 17:27:06   LiJ
 * Initial revision.
 * 
 *    Rev 1.0   Jul 09 2003 09:15:50   LiJ
 * Initial revision.
 * 
 * 
 *********************************************************************/
 
#include <string.h>
#include "lh79524_int_driver.h"
#include "lh79524_uart_driver.h"
#include "lh79524_gpio_driver.h"

#define RCPCBASE    0xFFFE2000
#define RCPC_CTRL   (RCPCBASE+0x0)

 
/* Board specific definition */

#define SDK79524_XTAL_IN    11289600 

/* Local defines for testing */

#define ESC_KEY     27
#define STR_SIZE    80
static  CHAR * greeting =   "You can key in something now! \r\n";
static  CHAR * end_string = "Example for polling mode done! \r\n";
static  CHAR output[STR_SIZE];
static  CHAR buffer[8];


void ext0_isr(void)
{
            *(volatile UNS_32 *)RCPC_CTRL |= 0x00;   /* take us from Active to Stop2 Mode */
}

/**********************************************************************
*
* Function: c_entry
*
* Purpose:
*   Function entry point from the startup code.
*  
* Processing:
*   
*
* Parameters:
*   None
*
* Outputs:
*   None
*
* Returns:
*   Nothing
*
* Notes:
*   None
*
**********************************************************************/
#define STR_SIZE    80
INT_32 c_entry (void)
{

    INT_32 dev_irq;
    INT_32 dev_uart;    /* UART handle */
    INT_32 index;       /* tmp variable */
    
    if ((dev_uart = uart_open(UART0_BASE, SDK79524_XTAL_IN)) == 0x0)
    {
        /* Error */
        return 1;
    }
    
    /* Operation mode configuration */
    uart_ioctl(dev_uart, UART_ENABLE_FIFO, 0);
    uart_ioctl(dev_uart, UART_ENABLE_RX, 0);
    uart_ioctl(dev_uart, UART_ENABLE_TX, 0);
    uart_ioctl(dev_uart, UART_START, 0);
    uart_ioctl(dev_uart, UART_SET_POLL_MODE, 0);        


    /* Output a string */
    uart_write(dev_uart, greeting, strlen(greeting));

    /* Set variables to accept new input chars */
    index = 0;
    output[0] = '\0';

/*
    // Open IRQ 
    if ((dev_irq = irq_open(0,0)) == 0x0)
    {
        //* Error opening the device 
        return 0;
    }
    
    // External interrupt trigger
    gpio_ext_int_init(EXT_INT0,0);	//low level trigger

    // Enable IRQ source 
    irq_ioctl(dev_irq, IRQ_ENABLE_SOURCE, VIC_EXINT0);
    
  	irq_ioctl(dev_irq, IRQ_SET_PRIORITY, 3);
    
   	// Set up interruption handler 
   	irq_ioctl(dev_irq, IRQ_SET_HANDLER, (INT_32)ext0_isr);

    // Enable global IRQ bit 
    irq_ioctl(dev_irq, IRQ_GLOBAL_ENABLE, 1);
*/

*(volatile UNS_32 *)RCPC_CTRL |= 0x8;   // take us from Active to Stop2 Mode 

    /* 
     * If the ESC key is pressed, exit from the while() loop.
     * If the ENTER key is pressed, or the number of input chars 
     * are more than the predefined string length, Echo back the string.
     */
    while (1)
    {
        /* Read in one char */
        while(uart_read(dev_uart, buffer, 1) == 0);
            
        buffer[1] = '\0';
        
        if(buffer[0] == ESC_KEY)
        {
            /* ESC key, exit */
            break;
        }
        else if((buffer[0] == '\r') || (index >= STR_SIZE))
        {
            /* Send string out */
            uart_write(dev_uart,"\r\n",2);
            uart_write(dev_uart, "You entered - ", 15);
            uart_write(dev_uart, output, strlen(output));
            uart_write(dev_uart,"\r\n",2);
            uart_write(dev_uart,"\r\n",2);
            /* Send out a greeting string. Set variables to accept a new string. */
            uart_write(dev_uart, greeting, strlen(greeting));
            output[0] = '\0';
            index = 0;
        }
        else
        {
            /* Received something */
            strcat(output, buffer);
            /* Echo the input */
            uart_write(dev_uart, buffer, 1);
        }
        index++;
    }

    /* Send out the prompt string before exit */
    uart_write(dev_uart, end_string, strlen(end_string));
    
    /* Close device */
    uart_close(dev_uart);
    
    return 0;
}


#ifdef __iar

void main(void)
{
	c_entry();
	while(1);
}

#endif