l3c6l3c6.lst

造纸自动化生产线的s7300程序

"V01.00.000"
"$_Languages"
"11(1) Finnish";"9(2) English (United Kingdom)"
"$_Timestamp"
"28.05.2004  15:13:32";"28.05.2004  15:13:32"
"$_Typ(LineComment)"
" Positive edge of 100ms clock pulse";" Positive edge of 100ms clock pulse"
" Positive edge of 200ms clock pulse";" Positive edge of 200ms clock pulse"
" Positive edge of 500ms clock pulse";" Positive edge of 500ms clock pulse"
" Positive edge of 1s clock pulse";" Positive edge of 1s clock pulse"
" Steps 0..15 active?";" Steps 0..15 active?"
" Steps 16..31 active?";" Steps 16..31 active?"
" Steps 32..47 active?";" Steps 32..47 active?"
" Steps 48..63 active?";" Steps 48..63 active?"
" Steps 64..77 active?";" Steps 64..77 active?"
" Stepping pulse and permit are blocked out";" Stepping pulse and permit are blocked out"
" Set active step to -1 if no active steps";" Set active step to -1 if no active steps"
" Pallet number > 8";" Pallet number > 8"
" -> not accepted";" -> not accepted"
" Pallet number < 0";" Pallet number < 0"
" Pallets diameters start from DW";" Pallets diameters start from DW"
" Diameter of selected head";" Diameter of selected head"
" Pallets types start from DW";" Pallets types start from DW"
" Type of selected head";" Type of selected head"
" Add two to priority pointer";" Add two to priority pointer"
" INT -> DINT";" INT -> DINT"
" Mask bit address";" Mask bit address"
" Load backstand or headshelf number";" Load backstand or headshelf number"
" If backstand or headshelf number is over 14";" If backstand or headshelf number is over 14"
" -> failure in priority list";" -> failure in priority list"
" If backstand or headshelf number is 0";" If backstand or headshelf number is 0"
" -> checking is done";" -> checking is done"
" OFFSET ";" OFFSET "
" Wrapper or head size";" Wrapper or head size"
" Wrapper or head type";" Wrapper or head type"
" Type";" Type"
" Requested type";" Requested type"
" Type is ok";" Type is ok"
" Size";" Size"
" Requested minimum size";" Requested minimum size"
" Requested maximum size";" Requested maximum size"
" Size is ok";" Size is ok"
" Type and size are ok";" Type and size are ok"
" Save first found size and backstand (or headshelf)";" Save first found size and backstand (or headshelf)"
" Save minimum found size and backstand (or headshelf)";" Save minimum found size and backstand (or headshelf)"
" Save maximum found size and backstand (or headshelf)";" Save maximum found size and backstand (or headshelf)"
" Back to start and check next in priority list";" Back to start and check next in priority list"
" If wrapper or head was found ";" If wrapper or head was found "
" -> jump over";" -> jump over"
" Load backstand or headshelf sizes start address";" Load backstand or headshelf sizes start address"
" Load first wrapper or head size";" Load first wrapper or head size"
" First wrapper or head size";" First wrapper or head size"
" Bytes 0 .. 3";" Bytes 0 .. 3"
" Bytes 4 .. 7";" Bytes 4 .. 7"
" DB13.DBW[#DRIVEtensionPOINT]";" DB13.DBW[#DRIVEtensionPOINT]"
" DB13.DBW[STOPbrMINpressurePOINT_D]";" DB13.DBW[STOPbrMINpressurePOINT_D]"
" DB13.DBW[STOPbrMAXpressurePOINT_D]";" DB13.DBW[STOPbrMAXpressurePOINT_D]"
"DB FOR DATA";"DB FOR DATA"
"LABELING ROLLDATA-DB";"LABELING ROLLDATA-DB"
" 1 ST. BEFORE LABELING ROLLDATA-DB";" 1 ST. BEFORE LABELING ROLLDATA-DB"
" 2 ST. BEFORE LABELING ST. ROLLDATA-DB";" 2 ST. BEFORE LABELING ST. ROLLDATA-DB"
" 3 ST. BEFORE LABELING ST. ROLLDATA-DB";" 3 ST. BEFORE LABELING ST. ROLLDATA-DB"
"LABEL REQUEST IS ON";"LABEL REQUEST IS ON"
"MILLCOMPUTER STARTED LABELPRINTING";"MILLCOMPUTER STARTED LABELPRINTING"
"LABEL PRINTED FOR LABELING-ROLL";"LABEL PRINTED FOR LABELING-ROLL"
"LABEL PRINTED PREVIOUS ST.";"LABEL PRINTED PREVIOUS ST."
"LABEL PRINTED FOR LABELING -2 ST";"LABEL PRINTED FOR LABELING -2 ST"
"LABEL PRINTED FOR LABELING -3 ST.";"LABEL PRINTED FOR LABELING -3 ST."
"EXTRA-LABEL PRINTED FOR LABELING";"EXTRA-LABEL PRINTED FOR LABELING"
"EXTRA-LABEL PRINTED FOR LABELING -1";"EXTRA-LABEL PRINTED FOR LABELING -1"
"LOGO-CUTTING";"LOGO-CUTTING"
" ALARM: REQUESTED LABEL >< PRINTED LABEL";" ALARM: REQUESTED LABEL >< PRINTED LABEL"
"  Positioning";"  Positioning"
"  Drive & crawling bits";"  Drive & crawling bits"
"  Positioning, control bits";"  Positioning, control bits"
"  Absolute encoder, error bits";"  Absolute encoder, error bits"
"  Positioning, tolerances & predefined places";"  Positioning, tolerances & predefined places"
"  Speedblocks";"  Speedblocks"
"  Kiihdytyksen miniminopeus = nopeus, jolla liike l鋒tee liikkeelle";"  Kiihdytyksen miniminopeus = nopeus, jolla liike l鋒tee liikkeelle"
"  Kiihdytyksen alapy鰎istys = kiihdytyksen aloituspy鰎istys";"  Kiihdytyksen alapy鰎istys = kiihdytyksen aloituspy鰎istys"
"  Kiihdytyksen skaalain = kiihdytyskerroin";"  Kiihdytyksen skaalain = kiihdytyskerroin"
"  Hidastuksen miniminopeus = loppunopeus; asetetaan nollaksi, jos halutaan ajaa kohteeseen ilman loppury鰉ityst