jpeg2000.txt

把一个图象转换为灰度图,把一个图象转换为灰度图

The following is from the JasPer Software Reference Manual (Version 1.600.0)
  Michael D. Adams
  Assistant Professor
  Dept. of Electrical and Computer Engineering
  University of Victoria
  Victoria, BC, Canada
  http://www.ece.uvic.ca/~mdadams/jasper/

imgareatlx=x
  Set the x-coordinate of the top-left corner of the image area to x.
imgareatly=y
  Set the y-coordinate of the top-left corner of the image area to y.
tilegrdtlx=x
  Set the x-coordinate of the top-left corner of the tiling grid to x.
tilegrdtly=y
  Set the y-coordinate of the top-left corner of the tiling grid to y.
tilewidth=w
  Set the nominal tile width to w.
tileheight=h
  Set the nominal tile height to h.
prcwidth=w
  Set the precinct width to w. The argument w must be an integer power of two. The default
  value is 32768.
prcheight=h
  Set the precinct height to h. The argument h must be an integer power of two. The default
  value is 32768.
cblkwidth=w
  Set the nominal code block width to w. The argument w must be an integer power of two.
  The default value is 64.
cblkheight=h
  Set the nominal code block height to h. The argument h must be an integer power of two. 
  The default value is 64.
mode=m
  Set the coding mode to m. The argument m must have one of the following values:
    int  : integer mode
    real : real mode    
  If lossless coding is desired, the integer mode must be used. By default, the integer mode
  is employed. The choice of mode also determines which multicomponent and wavelet transforms
  (if any) are employed.  
rate=r
  Specify the target rate. The argument r is a positive real number. Since a rate of one 
  corresponds to no compression, one should never need to explicitly specify a rate greater 
  than one. By default, the target rate is considered to be infinite.
ilyrrates=r0[,r1,. . . ,rN  
  Specify the rates for any intermediate layers. The argument to this option is a comma 
  separated list of N rates. Each rate is a positive real number. The rates must increase 
  monotonically. The last rate in the list should be less than or equal to the overall rate 
  (as specified with the rate option).
prg=p
  Set the progression order to p. The argument p must have one of the following values:
    lrcp : layer-resolution-component-position (LRCP) progressive (i.e., rate scalable)
    rlcp : resolution-layer-component-position (RLCP) progressive (i.e., resolution scalable)
    rpcl : resolution-position-component-layer (RPCL) progressive
    pcrl : position-component-resolution-layer (PCRL) progressive
    cprl : component-position-resolution-layer (CPRL) progressive
  By default, LRCP progressive ordering is employed. Note that the RPCL and PCRL 
  progressions are not valid for all possible image geometries. (See [4] for more details.)
nomct
  Disallow the use of any multicomponent transform.
numrlvls=n
  Set the number of resolution levels to n. The argument n must be an integer that is 
  greater than or equal to one. The default value is 6.
sop
  Generate SOP marker segments.
eph
  Generate EPH marker segments.
lazy
  Enable lazy coding mode (a.k.a. arithmetic coding bypass).
termall
  Terminate all coding passes.
segsym
  Use segmentation symbols.
vcausal
  Use vertically stripe causal contexts.
pterm
  Use predictable termination.
resetprob
  Reset the probability models after each coding pass.
numgbits=n
  Set the number of guard bits to n.