tms470r1b1m_i2c_03.c

TMS470的Ｉ２Ｃ总线源码

//******************************************************************************
// TMS470 Demo - I2C Sample Program I2C2
//
// This is a I2C2 Slave Interrupt configuration.
// Data is recieved from I2C2 and displayed on the LED array.
// Clock speed is 60 MHz. Data size is 8 bits. These signals are connected on
// the same board.
//
//
//                              TMS-FET470B1M
//                             _________________
//                            |                 |
//                         /|\|            OSCIN|-
//                          | |                 | 7.5MHz
//                          --|PLLDIS     OSCOUT|-
//                            |                 |
//                            |----- I2C2 ------|
//                            |             SCL |---
//                            |                 |
//                            |             SDA |---
//                            |_________________|
//
//
//
//
//  J. Mangino / A. Dannenberg
//  Texas Instruments, Inc
//  August 2005
//  Built with IAR Embedded Workbench Version: 4.30A
//******************************************************************************

#include <intrinsic.h>
#include "iotms470r1b1m.h"
#include "tms470r1b1m_bit_definitions.h"

unsigned int datp;

void TMS470LedSet(unsigned int mask)
{
  GIODOUTE = mask & 0xFF;
  HETDOUT = (mask & 0xFF00)>>8;
}

void I2C2_irq_handler()
{
  datp = I2C2DRR&0XFF;
  TMS470LedSet(datp);
}

//------------------------------------------------------------------------------
// TMS470R1B1M Standard Interrupt Handler
//------------------------------------------------------------------------------
__irq __arm void irq_handler(void)
{
  switch((0xff & IRQIVEC)-1)
  {
    case CIM_I2C2   : I2C2_irq_handler(); break;
  }
}

void main(void)
{
  // Set up peripheral registers.
  // First disable interrupts.
  __disable_interrupt();

  // Setup system.
  PCR = CLKDIV_2;                                      // ICLK = SYSCLK/2
  PCR |= PENABLE;                                      // enable peripherals
  GCR = ZPLL_CLK_DIV_PRE_1;                            // SYSCLK = 8 x fOSC
  REQMASK =  (1 << CIM_I2C2);                          // Enable I2C Interrupt mask


  HETDIR  = 0xff;                                       // Set HET as GIO outputs
  HETDOUT = 0xff;                                       // Output on
  HETDOUT = 0x00;                                       // Output off
  HETDOUT = 0xff;                                       // Output on
  GIODIRE = 0xff;                                       // Set GIO outputs
  GIODOUTE =0xff;                                       // Output on

  //I2C 2 Set up
  I2C2PSC = 2;                                          // Module clock frequency
                                                        // I2CCLK = ICLK / (PSC + 1)
                                                        // I2CCLK = 10 MHz
  I2C2CKL = 38;                                         // Low clock period
  I2C2CKH = 38;                                         // High clock period
  I2C2OAR = 0x48;                                       // Set address 0x48
  I2C2IMR = 0x08;                                       // Interrupts receive enabled
  I2C2CNT = 1;                                          // Set count = 1
  I2C2SAR = 0x56;                                       // Set address 0x56
  I2C2PFNC = 0;
  I2C2DIR = SDAFUNC+SCLFUNC;                            // Set I2C Functions
  I2C2MDR |= NIRS;                                      // Clear reset

  __enable_interrupt();                                // Enable Interrupts

  // Loop forever.
  while (1);
}