ext3.txt

Linux Kernel 2.6.9 for OMAP1710

Ext3 Filesystem
===============

ext3 was originally released in September 1999. Written by Stephen Tweedie
for 2.2 branch, and ported to 2.4 kernels by Peter Braam, Andreas Dilger, 
Andrew Morton, Alexander Viro, Ted Ts'o and Stephen Tweedie.

ext3 is ext2 filesystem enhanced with journalling capabilities. 

Options
=======

When mounting an ext3 filesystem, the following option are accepted:
(*) == default

jounal=update		Update the ext3 file system's journal to the 
			current format.

journal=inum		When a journal already exists, this option is 
			ignored. Otherwise, it specifies the number of
			the inode which will represent the ext3 file
			system's journal file.

noload			Don't load the journal on mounting.

data=journal		All data are committed into the journal prior
			to being written into the main file system.

data=ordered	(*)	All data are forced directly out to the main file
			system prior to its metadata being committed to
			the journal.

data=writeback		Data ordering is not preserved, data may be
			written into the main file system after its
			metadata has been committed to the journal.

commit=nrsec	(*)	Ext3 can be told to sync all its data and metadata
			every 'nrsec' seconds. The default value is 5 seconds.
			This means that if you lose your power, you will lose,
			as much, the latest 5 seconds of work (your filesystem
			will not be damaged though, thanks to journaling). This
			default value (or any low value) will hurt performance,
			but it's good for data-safety. Setting it to 0 will
			have the same effect than leaving the default 5 sec.
			Setting it to very large values will improve
			performance.

barrier=1		This enables/disables barriers. barrier=0 disables it,
			barrier=1 enables it.

orlov		(*)	This enables the new Orlov block allocator. It's enabled
			by default.

oldalloc		This disables the Orlov block allocator and enables the
			old block allocator. Orlov should have better performance,
			we'd like to get some feedback if it's the contrary for
			you.

user_xattr	(*)	Enables POSIX Extended Attributes. It's enabled by
			default, however you need to confifure its support
			(CONFIG_EXT3_FS_XATTR). This is neccesary if you want
			to use POSIX Acces Control Lists support. You can visit
			http://acl.bestbits.at to know more about POSIX Extended
			attributes.

nouser_xattr		Disables POSIX Extended Attributes.

acl		(*)	Enables POSIX Access Control Lists support. This is
			enabled by default, however you need to configure
			its support (CONFIG_EXT3_FS_POSIX_ACL). If you want
			to know more about ACLs visit http://acl.bestbits.at

noacl			This option disables POSIX Access Control List support.

reservation

noreservation

resize=

bsddf 		(*)	Make 'df' act like BSD.
minixdf			Make 'df' act like Minix.

check=none		Don't do extra checking of bitmaps on mount.
nocheck		

debug			Extra debugging information is sent to syslog.

errors=remount-ro(*)	Remount the filesystem read-only on an error.
errors=continue		Keep going on a filesystem error.
errors=panic		Panic and halt the machine if an error occurs.

grpid			Give objects the same group ID as their creator.
bsdgroups		

nogrpid		(*)	New objects have the group ID of their creator.
sysvgroups

resgid=n		The group ID which may use the reserved blocks.

resuid=n		The user ID which may use the reserved blocks.

sb=n			Use alternate superblock at this location.

quota			Quota options are currently silently ignored.
noquota			(see fs/ext3/super.c, line 594)
grpquota
usrquota


Specification
=============
ext3 shares all disk implementation with ext2 filesystem, and add
transactions capabilities to ext2.  Journaling is done by the
Journaling block device layer.

Journaling Block Device layer
-----------------------------
The Journaling Block Device layer (JBD) isn't ext3 specific.  It was
design to add journaling capabilities on a block device.  The ext3
filesystem code will inform the JBD of modifications it is performing
(Call a transaction).  the journal support the transactions start and
stop, and in case of crash, the journal can replayed the transactions
to put the partition on a consistent state fastly.

handles represent a single atomic update to a filesystem.  JBD can
handle external journal on a block device.

Data Mode
---------
There's 3 different data modes:

* writeback mode
In data=writeback mode, ext3 does not journal data at all.  This mode
provides a similar level of journaling as XFS, JFS, and ReiserFS in its
default mode - metadata journaling.  A crash+recovery can cause
incorrect data to appear in files which were written shortly before the
crash.  This mode will typically provide the best ext3 performance.

* ordered mode
In data=ordered mode, ext3 only officially journals metadata, but it
logically groups metadata and data blocks into a single unit called a
transaction.  When it's time to write the new metadata out to disk, the
associated data blocks are written first.  In general, this mode
perform slightly slower than writeback but significantly faster than
journal mode.

* journal mode
data=journal mode provides full data and metadata journaling.  All new
data is written to the journal first, and then to its final location. 
In the event of a crash, the journal can be replayed, bringing both
data and metadata into a consistent state.  This mode is the slowest
except when data needs to be read from and written to disk at the same
time where it outperform all others mode.

Compatibility
-------------

Ext2 partitions can be easily convert to ext3, with `tune2fs -j <dev>`.
Ext3 is fully compatible with Ext2.  Ext3 partitions can easily be
mounted as Ext2.

External Tools
==============
see manual pages to know more.

tune2fs: 	create a ext3 journal on a ext2 partition with the -j flags
mke2fs: 	create a ext3 partition with the -j flags
debugfs: 	ext2 and ext3 file system debugger

References
==========

kernel source:	file:/usr/src/linux/fs/ext3
		file:/usr/src/linux/fs/jbd

programs: 	http://e2fsprogs.sourceforge.net

useful link:
		http://www.zip.com.au/~akpm/linux/ext3/ext3-usage.html
		http://www-106.ibm.com/developerworks/linux/library/l-fs7/
		http://www-106.ibm.com/developerworks/linux/library/l-fs8/